• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11b
• /
• pp.13-14
• /
• 2004

Using Se as a photoconductive element and ZnS as a luminescent element, a Se/ZnS thin film device for light amplifier applications was fabricated and its characteristics were investigated At various conditions of substrate temperatures, heat treatment times, and heat treatment temperatures, Se thin films and ZnS thin films were separately deposited by an EBE(Electron Beam Evaporation) method of an high accuracy in deposition rates and the optimum fabrication conditions for the Se thin film and the ZnS thin film with a hexagonal structure were obtained The Se/ZnS thin film light amplifier was fabricated by evaporating the ZnS thin film on an ITO(Indium Tin Oxide) glass and the Se thin film on the ZnS thin film in sequence.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.307-310
• /
• 1999

Using Se as a photoconductive element and ZnS as a luminescent element, a Se/ZnS thin film device for light amplifier applications was fabricated and its characteristics were investigated. The Se/ZnS thin film light amplifier was fabricated by evaporating the ZnS thin film on an ITO(Indium Tin Oxide) glass and the Se thin film on the ZnS thin film in sequence. The results of the characteristics investigation are summarized as follows: (1) When the frequency of an excitation voltage was increased, both the brightness response and the brightness saturation of the Se/ZnS thin film light amplifier began to start at a higher light input. (2) The gain of the Se/ZnS thin film light amplifier was dependent upon the amplitude and the frequency of the excitation voltage as well as an external light input. (3) When the Se/ZnS thin film light amplifier was excited by a direct current of a constant voltage, the frequency of the output brightness was\\`equal to the frequency of the input light applied. When the light amplifier was excited by a sinusoidal voltage of 60 Hz, the frequency of the output brightness was 120 Hz.

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.54-62
• /
• 2007

In this paper, we report the research highlight on the preparation and characterization of Indium-free $Cu_2ZnSnSe_4$ and Indium-reduced $CulnZnSe_2$ thin films in order to seek the viability of these absorber materials to be applied in thin film solar cells. The films of $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ were prepared using mixed binary chalcogenides powders. It was observed that Cu concentration was a function of substrate temperature as well as CuSe mole ratio in the target. Under an optimized condition, $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ thin films grew with strong [112]. [220/204] and [312/116] reflections. Both $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ films were found to exhibit a high absorption coefficient of $104^4cm^{-1}\;Cu_2ZnSnSe_4$ film showed a band gap of 1.5eV which closes to the optimum band gap of an ideal solar absorber for a solar cell. On the other side, an increase of optical band gap from 1.0 to 1.25eV was found to be proportional with an increase of Zn concentration in the $CulnZnSe_2$ film. All films in this study revealed a p-type semiconductor characteristic.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.4
• /
• pp.19-22
• /
• 2008

Thin film has been an increasing important subject of intensive research, owing to the fact that these films possess desirable optical, electrical and electrochemical properties for uses in many semi-conducting nano-crystal applications, such as light-emitting diodes, lasers and solar cell applications. Here, ZnSe thin films were deposited by electrochemical method for the applications of light emitting diode. Electrochemical deposition of ZnSe thin film is not easy, because of the high difference of reduction potential between zinc ion and selenium acid. In order to handle the band gap of ZnSe crystal thin films easily, electrochemical methods are promising to manufacture these films economically. Therefore we have investigated the present study to characterize zinc selenide thin films deposited on ITO glass plates electrochemically. The luminescent properties of ZnSe films have been evaluated by UV-Vis spectrometer and luminescence spectrometer. And the morphology of the film surface has been discussed qualitatively from SEM images.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.86.2-86.2
• /
• 2015

Cu2ZnSn(S,Se)4 thin film solar cells have been fabricated using sputtered Cu/Sn/Zn metallic precursors on Mo coated sodalime glass substrate without using a toxic H2Se and H2S atmosphere. Cu/Sn/Zn metallic precursors with various thicknesses were prepared using DC magnetron sputtering process at room temperature. As-deposited metallic precursors were sulfo-selenized inside a graphite box containing S and Se pellets using rapid thermal processing furnace at various sulfur to selenium (S/Se) compositional ratio. Thin film solar cells were fabricated after sulfo-selenization process using a 65 nm CdS buffer, a 40 nm intrinsic ZnO, a 400 nm Al doped ZnO, and Al/Ni top metal contact. Effects of sulfur to selenium (S/Se) compositional ratio on the microstructure, crystallinity, electrical properties, and cell efficiencies have been studied using X-ray diffraction, Raman spectroscopy, field emission scanning electron microscope, I-V measurement system, solar simulator, quantum efficiency measurement system, and time resolved photoluminescence spectrometer. Our fabricated Cu2ZnSn(S,Se)4 thin film solar cell shows the best conversion efficiency of 9.24 % (Voc : 454.6 mV, Jsc : 32.14 mA/cm2, FF : 63.29 %, and active area : 0.433 cm2), which is the highest efficiency among Cu2ZnSn(S,Se)4 thin film solar cells prepared using sputter deposited metallic precursors and without using a toxic H2Se gas. Details about other experimental results will be discussed during the presentation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.270-273
• /
• 2007

In this report, Indium-free and Indium-reduced thin film materials for solar absorber were studied in order to search alternative materials for thin film solar cell. The films of $Cu_2ZnSnSe_4$ and $Cu_2ZnSnSe_2$ were deposited using mixed binary chalcogenides powders. From the film bulk analysis result, it is observed that Cu concentration is a function of substrate temperature as well as CuSe mole ratio in the target. Under optimized conditions, $Cu_2ZnSnSe_4$ and $Cu_2ZnSnSe_2$ thin films grow with strong (112), (220/204) and (312/116) reflections. Films are found to exhibit a high absorption coefficient of $10^4$ $cm^{-1}$. $Cu_2ZnSnSe_4$ film shows a 1.5 eV band gap. On the other side, an increasing of optical band gap from 1.0 eV to 1.25 eV ($CuInSnSe_2$) is found to be proportional with an increasing of Zn concentration. All films have a p-type semiconductor characteristic with a carrier concentration in the order of $10^{14}$ $cm^{-3}$, a mobility about $10^1$ $cm^{2{\cdot}-1.}S^{-1}$ and a resistivity at the range of $10^2-10^6$ ${\Omega}{\cdot}m$.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.714-721
• /
• 2013

A stoichiometric mixture of evaporating materials for $ZnAl_2Se_4$ single-crystal thin films was prepared in a horizontal electric furnace. These $ZnAl_2Se_4$ polycrystals had a defect chalcopyrite structure, and its lattice constants were $a_0=5.5563{\AA}$ and $c_0=10.8897{\AA}$.To obtain a single-crystal thin film, mixed $ZnAl_2Se_4$ crystal was deposited on the thoroughly etched semi-insulating GaAs(100) substrate by a hot wall epitaxy (HWE) system. The source and the substrate temperatures were $620^{\circ}C$ and $400^{\circ}C$, respectively. The crystalline structure of the single-crystal thin film was investigated by using a double crystal X-ray rocking curve and X-ray diffraction ${\omega}-2{\theta}$ scans. The carrier density and mobility of the $ZnAl_2Se_4$ single-crystal thin film were $8.23{\times}10^{16}cm^{-3}$ and $287m^2/vs$ at 293 K, respectively. To identify the band gap energy, the optical absorption spectra of the $ZnAl_2Se_4$ single-crystal thin film was investigated in the temperature region of 10-293 K. The temperature dependence of the direct optical energy gap is well presented by Varshni's relation: $E_g(T)=E_g(0)-({\alpha}T^2/T+{\beta})$. The constants of Varshni's equation had the values of $E_g(0)=3.5269eV$, ${\alpha}=2.03{\times}10^{-3}eV/K$ and ${\beta}=501.9K$ for the $ZnAl_2Se_4$ single-crystal thin film. The crystal field and the spin-orbit splitting energies for the valence band of the $ZnAl_2Se_4$ were estimated to be 109.5 meV and 124.6 meV, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}_5$ states of the valence band of the $ZnAl_2Se_4/GaAs$ epilayer. The three photocurrent peaks observed at 10 K are ascribed to the $A_1$-, $B_1$-exciton for n = 1 and $C_{21}$-exciton peaks for n = 21.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.13-16
• /
• 2003

Mn-doped $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin film phosphors have been grown using a pulsed laser deposition technique under various growth conditions. The structural characterization carr~ed out on a series of $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) films grown on MgO(l00) substrates usmg Zn-rich ceramic targets. Oxygen pressure was varied from 50 to 200 mTorr and Zn/Ga ratio was the function of oxygen pressure. XRD patterns showed that the lattice constants of the $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin film decrease with the substitution of sulfur and selenium for the oxygen in the $ZnGa_2O_4$. Measurements of photoluminescence (PL) properties of $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin films have indicated that MgO(100) is one of the most promised substrates for the growth of high quality $ZnGa_2O_{4-x}M_{x}$:$Mn^{2+}$ (M=S, Se) thin films. In particular, the incorporation of Sulfur or Selenium into $ZnGa_2O_4$ lattice could induce a remarkable increase in the intensity of PL. The increasing of green emission intensity was observed with $ZnGa_2O_{3.925}Se_{0.075}:$Mn^{2+}$ and $ZnGa_2O_{3.925}S_{0.05}$:$Mn^{2+}$ films, whose brightness was increased by a factor of 3.1 and 1.4 in comparison with that of $ZnGa_{2}O_{4}$:$Mn^{2+}$ films, respectively. These phosphors may promise for application to the flat panel displays.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.211.1-211.1
• /
• 2013

We fabricate the conductive zinc oxide(ZnO) thin film using UV-enhanced atomic layer deposition. ZnO is semiconductor with a wide band gap(3.37eV) and transparent in the visible region. ZnO can be deposited with various method, such as metal organic chemical vapour deposition, magnetron sputtering and pulsed laser ablation deposition. In this experiment, ZnO thin films was deposited by atomic layer deposition using diethylzinc (DEZ) and D.I water as precursors with UV irradiation during water dosing. As a function of UV exposure time, the resistivity of ZnO thin films decreased dramatically. We were able to confirm that UV irradiation is one of the effective way to improve conductivity of ZnO thin film. The resistivity was investigated by 4 point probe. Additionally, we confirm the thin film composition is ZnO by X-ray photoelectron spectroscopy. We anticipate that this UV-enhanced ZnO thin film can be applied to electronics or photonic devices as transparent electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.120-121
• /
• 2009

Single crystalline $ZnIn_2Se_4$ layers were grown on thoroughly etched semi-insulating GaAs(100) substrate at $400^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating, $ZnIn_2Se_4$ source at $630^{\circ}C$. After the as-grown $ZnIn_2Se_4$ single crystalline thin films was annealed in Zn-, Se-, and In-atmospheres, the origin of point defects of $ZnIn_2Se_4$single crystalline thin films has been investigated by the photoluminescence(PL) at 10 K The native defects of $V_{Zn}$, $V_{Se}$, $Zn_{int}$ and $Se_{int}$ obtained by PL measurements were classified as a donors or acceptors type. And we concluded that the heat-treatment in the Se-atmosphere converted $ZnIn_2Se_4$ single crystalline thin films to an optical p-type. Also, we confirmed that In in $ZnIn_2Se_4$/GaAs did not form the native defects because In in $ZnIn_2Se_4$ single crystalline thin films existed in the form of stable bonds.