• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.365-365
• /
• 2013

본 실험에서는 RF magnetron sputter장비와 evaporator장비를 이용하여 다층박막 IGZO/Ag/IGZO를 제작하였다. 소결된 타겟은 In:Ga:ZnO 1:1:1mol%로 조성된 타겟을 사용하였으며, Ag는 99.999%의 순도를 가진다.다층박막 OMO구조의 Oxide layer는sputter장비를 이용 IGZO막을 제작하였으며, Metal layer는 evaporator 장비를 이용 Ag막을 제작하였다. 변수로는 Metal layer 두께에 따른 구조적, 광학적 특성 변화를 연구하였다. Oxide layer의 RF sputter 공정 조건으로는 초기압력 $3.0{\times}10^{-6}$ Torr 이하로 하였으며, 증착압력 $2.0{\times}10^{-2}$ Torr, RF power 30 W, Ar 50 sccm으로 고정시켰으며, Metal layer의 evaporator 공정조건으로는 $5.0{\times}10^{-6}$ 이하, 전압은 0.3V, 기판 회전속도는 2RPM 두께는 Thickness moniter로 3. 5. 7. 9. 11. 13. 15 nm를 확인하며 증착하였다. 분석결과로는 AFM측정결과 거칠기는 2 nm이하의 거칠기를 확인했으며, XRD측정결과 Bragg's 법칙($2\;dsin{\Theta}=n{\lambda}$)를 만족하는 피크를 찾을 수 없어 비정질 구조임을 확인할 수 있었다. 투과도 측정결과 가시광 영역에서 최대 80% 이상의 투과율을 보여주었으며, IR영역에서는 30% 이하의 투과율을 보여주었다. 에너지 밴드갬 계산결과 4.5~4.6 eV를 갖는 것을 확인하였으며, Low-e 분야에 사용가능함을 보여주었다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2006.06a
• /
• pp.23-24
• /
• 2006

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.351-351
• /
• 2013

한국 전체 에너지 사용량 중약 24%의 에너지가 건축물 부분에 소비되고 있다. 건축물의 벽체나 유리창 등을 통해서 에너지 손실이 이루어지는데 유리창은 벽체에 비해 약 10배 이상 낮은 단열 특성을 가지고 있기 때문에 유리창을 통한 열손실량은 더 크다. 이러한 유리창 부분의 열손실 문제를 해결할 수 있는 방안으로 좋은 단열 특성 및 낮은 방사율을 가지고 있는 Low-e coating 방법을 사용하였다. 본 실험에서는 XG glass 기판 위에 IGZO/Ag/IGZO OMO 구조의 다층 박막을 증착하였다. RF magnetron sputtering방법을 이용하여 OMO 구조의 상부와 하부의 Oxide layer로 IGZO 박막을 증착하였다. 사용된 IGZO 타겟은 $In_2O_3$ (99.99%), $Ga_2O_3$ (99.99%), ZnO (99.99%)의 분말을 각각 1:1:1 mol% 조성비로 혼합하여 소결하여 제작하였다. Thermal Evaporator 장비를 이용하여 OMO 구조의 Metal layer로 Ag (99.999%)를 증착하였다. 실험 기판은 크기 $30{\times}30mm$의 0.7T XG glass를 사용하였다. OMO 구조의 산화층 IGZO 박막은 상/하층 동일 조건으로 기판 온도는 실온으로 고정하였으며, 초기 압력 $3.0{\times}10^{-6}$ Torr, 증착 압력 $3.0{\times}10^{-2}$ Torr, RF 파워 50W, Ar 유량 50 sccm로 고정시키고 증착 시간이 변화하면서 박막을 증착하였다. OMO 구조의 Metal layer로 Ag 증착 조건은 초기 진공도가 약 $6.0{\times}10^{-6}$ Torr 이하로 유지하고 기판을 2 Rpm의 속도로 회전시켰다. 이후 0.3 V로 Ag를 10분간 가열하여 충분히 녹인 후 Film Thickness Monitor로 두께를 확인하였다. OMO 다층 박막의 산화물층 변화에 따라 로이다층 박막의 구조적, 광학적 및 전기적 특성을 분석하였다. XRD 분석결과에 의하여 Bragg's 법칙을 만족하는 피크가 나타나지 않는 비정질 구조임을 확인할 수 있으며, AFM 분석결과에 통해서 최소 1.3 nm의 Roughness를 나타내었다. UV-Visible-NIR 분광광도계를 이용하여 다층 박막은 가시광선 영역에서 평균 80%의 광 투과성을 보여 IR 영역에서 평균 30% 투과하고 좋은 차단 특성을 나왔다. Low-e 특성을 갖는 유리창을 통해서 에너지 절약을 이룰 수 있는 것을 확인할 수 있었다.

• Environmental Analysis Health and Toxicology
• /
• v.25 no.1
• /
• pp.19-26
• /
• 2010

Discharged materials from the point or non-point source are released into the sea, and as the results, marine environment is directly affected. We must estimate the impacts of contaminants to marine pollution rapidly and accurately. Therefore, it is needed on early warning system for appreciating marine environmental impacts, and required a bioassay to evaluate abnormal changes. A bioassay test was developed to examine the effects of heavy metal contaminants on the early life stages of the marine annimals. We have studied the effects of metals on early development of a sea urchin species, Strongylocentrotus intermedius. S. intermedius embryos were tested with six metals (Cu, Ag, Zn, Cd, Cr, Ni) and showed the highest sensitivity to Cu as well as the lowest sensitivity to Cd. The order of biological impact for metals was Cu>Ag>Ni>Zn>Cr>Cd. In accordance with the results, sea urchins embryos can provide biological criteria for seawater quality assessment. The sensitivity of developmental bioassay whith S. intermedius is at intermediate level among marine organisms commonly used in aquatic bioassays. And this sea urchin can be routinely employed as a test organism for ecotoxicity assays.

• Nuclear Engineering and Technology
• /
• v.54 no.3
• /
• pp.1030-1036
• /
• 2022

A high detection efficiency thermal neutron detector based on the ⁶LiF/ZnS(Ag) scintillation screens, wavelength-shifting fibers (WLSF) and Silicon photomultiplier (SiPM) readout is under development at China Spallation Neutron Source (CSNS) for the Engineering Material Diffractometer (EMD).A prototype with a sensitive volume of 180mm×192mm has been built. Signals from SiPMs are processed by the self-design Application Specific Integrated Circuit (ASIC). The performances of this detector prototype are as follows: neutron detection efficiency could reach 50.5% at 1 Å, position resolution of 3, the dark count rate <0.1Hz, the maximum count rate >200KHz. Such detector prototype could be an elementary unit for applications in the EMD detector arrays.

• Analytical Science and Technology
• /
• v.10 no.3
• /
• pp.187-195
• /
• 1997

Chemically modified electrodes(CMEs) for Ag(I) were constructed by incoporating 1,5,9,13-tetrathiacyclohexadecane([16]-ane-$S_4$) with a conventional carbon-paste mixture composed of graphite powder and nujol oil. Ag(I) ion was chemically deposited onto the surface of the modified electrode with [16]-ane-$S_4$ by immersion of the electrode in the acetate buffer solution(pH=4.5) containing $5.0{\times}10^{-4}M$ Ag(I) ion. And then the electrode deposited with Ag(I) was reduced at -0.3V vs. S.C.E. Well-defined stripping voltammetric peaks could be obtained by scanning the potential to the positive direction. The CME surface was regenerated with exposure to 0.1M $HNO_3$ solution and was reused for the determination of Ag(I) ion. When deposition/measurement/regeneration cycles were 10 times, the response could be reproduced with relative standard deviation of 6.08%. In case of differential pulse stripping voltammetry, the calibration curve for Ag(I) was linear over the range of $5.0{\times}10^{-7}{\sim}1.5{\times}10^{-6}M$. And the detection limit was $2.0{\times}10^{-7}M$. Various ions such as Cd(II), Ni(II), Pb(II), Zn(II), Mn(II), Mg(II), EDTA, and oxalate(II) did not influence the determination of Ag(I) ion, except Cu(II) ion.

• Korean Journal of Materials Research
• /
• v.32 no.2
• /
• pp.94-97
• /
• 2022

We fabricated 3 types of ETL, mp TiO₂, ZnO, and ZnO coated on mp TiO₂(ZMT) to compare the photoelectric conversion efficiency (PCE) and fill factor (FF) of Perovskite solar cells. The structure of the cells was FTO/ETL/Perovskite (CH₃NH₃PbI₃)/spiro-MeOTAD/Ag. SEM morphology assessment of the ETLs showed that mp TiO₂ was porous, ZnO was flat, and the ZMT porous surface was filled with a thin layer. Via XRD measurements, the crystal structures of mp TiO₂ and ZnO ETL were found to be anatase and wurtzite, respectively. The XPS patterns showing energy bonding of mp TiO₂, ZnO, and ZMT O 1s confirmed these materials to be metal oxides such as ETL. The electrical characteristics of the Perovskite solar cells were measured using a solar simulator. Perovskite solar cells with ZMT ETL showed showed PCE of 10.29 % than that of conventional mp TiO₂ ETL devices. This was considered a result of preventing Perovskite from seeping into the ETL and preventing recombination of electrons and holes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.105-106
• /
• 2013

Surface plasmon resonance (SPR) is classified into the propagating surface plasmon (PSP) excited on flat metal surfaces and the local surface plasmon (LSP) excited by metalnanoparticles. It is known that fluorescence signals are enhanced by these two SPR-fields.On the other hand, fluorescence is quenched by the energy transfer to metal (FRET). Bothphenomena are controlled by the distance between dyes and metals, and the degree offluorescence enhancement is determined by the correlation. In this study, we determined thecondition to achieve the maximum fluorescence enhancement by adjusting the distance of ametal nanoparticle 2D sheet and a quantum dots 2D sheet by the use of $SiO_2$ spacer layers. The 2D sheets consisting of myristate-capped Ag nanoparticles (AgMy nanosheets) wereprepared at the air-water interface and transferred onto hydrophobized gold thin films basedon the Langmuir-Schaefer (LS) method [1]. The $SiO_2$ sputtered films with different thickness (0~100 nm) were deposited on the AgMy nanosheet as an insulator. TOPO-cappedCdSe/CdZnS/ZnS quantum dots (QDs, ${\lambda}Ex=638nm$) [2] were also transferred onto the $SiO_2$ films by the LS method. The layered structure is schematically shown in Fig. 1. The result of fluorescence measurement is shown in Fig. 2. Without the $SiO_2$ layer, the fluorescence intensity of the layered QD film was lower than that of the original QDs layer, i.e., the quenching by FRET was predominant. When the $SiO_2$ thickness was increased, the fluorescence intensity of the layered QD film was higher than that of the original QDs layer, i.e., the SPR enhancement was predominant. The fluorescence intensity was maximal at the $SiO_2$ thickness of 20 nm, particularly when the LSPR absorption wavelength (${\lambda}=480nm$) was utilized for the excitation. This plasmonic nanosheet can be integrated intogreen or bio-devices as the creation point ofenhanced LSPR field.

• Korean Journal of Environmental Biology
• /
• v.22 no.3
• /
• pp.394-399
• /
• 2004

A BOD sensor was prepared with S. marcescens LSY4 and was applied for measurement of BOD values of a solution containing the standard organic pollutants. The sensor sensitivity was nearly independent of the culture time in the range of 9-16 hours. It was also affected little by the cell mass in the range of 0.22-0.75 mg $cm^{-2}$. A cyclic change in the solution pH in the range of 4-9 was accompanied by a reversible variation in the sensor sensitivity. However, the reversibility was lost when the solution pH became more acidic or more basic. Heavy metal ions lowered the sensor sensitivity, which took place more precipitously in the presence of $Cu^{2+}$ and $Ag^+$ rather than in the presence of $Zn^{2+}$ and $Cd^{2+}$. The reduction of the sensor sensitivity was significantly attenuated by loading heavy metal ion tolerance induced strain. The $Cu^{2+}$tolerance induced strain was more efficient for the attenuation than $Zn^{2+}$ and $Cd^{2+}$ tolerance induced strain.

• Korean Journal of Food Science and Technology
• /
• v.12 no.1
• /
• pp.1-5
• /
• 1980

Crude invertase was obtained from the water extracts of Korean ginseng, Panax ginseng C. A. Meyer, by fractionation with $0.8{\sim}1.0$ saturation of ammonium sulfate. The properties of the crude invertase were as follows: Crude invertase was stable in the pH range between 5 and 9, and at the temperature below $35^{\circ}C$. Crude invertase showed the optimum pH at 5.0 and the optimum temperature at $50^{\circ}C$. The activity of the crude invertase was inhibited by $Ag^{+}\;Mn^{+}\;Hg^{+}\;Zn^{+},\;and\;Rb^{+}$, while $Ca^{+}\;Cu^{+},\;and\;Fe^{3+}$ demonstrated remarkable increasing effects on the enzyme activity.