• 대한기계학회논문집B
• /
• 제29권9호
• /
• pp.1065-1073
• /
• 2005

The thermal conductivity of water- and ethylene glycol-based nanofluids containing alumina $(Al_2O_3)$, zinc oxide (ZnO) and titanium dioxide $(TiO_2)$ nanoparticles is measured by varying the particle diameter and volume fraction. The transient hot-wire method using an anodized tantalum wire for electrical insulation is employed for the measurement. The experimental results show that nanofluids have substantially higher thermal conductivities than those of the base fluid and the ratio of thermal conductivity enhancement increases linearly with the volume fraction. It has been found that the ratio of thermal conductivity enhancement increases with decreasing particle size but no empirical or theoretical correlation can explain the particle-size dependence of the thermal conductivity. This work provides, for the first time to our knowledge, a set of consistent experimental data over a wide range of nanofluid conditions and can therefore serve as a basis for developing theoretical models to predict thermal conduction phenomena in nanofluids.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.120-120
• /
• 2003

The metallic oxide nanomaterials including ZnO, Ga$_2$O$_3$, TiO$_2$, and SnO$_2$ have been synthesized by a number of methods including laser ablation, arc discharge, thermal annealing procedure, catalytic growth processes, and vapor transport. We have been interested in preparing the nanomaterials of Ga$_2$O$_3$, which is a wide band gap semiconductor (E$_{g}$ =4.9 eV) and used as insulating oxide layer for all gallium-based semiconductor. Ga$_2$O$_3$ is stable at high temperature and a transparent oxide, which has potential application in optoelectronic devices. The Ga$_2$O$_3$ nanoparticles and nanobelts were produced using GaN single crystals, which were grown by flux method inside SUS$^{TM}$ cell using a Na flux and exhibit plate-like morphologies with 4 ~ 5 mm in size. In these experiments, the conventional electric furnace was used. GaN single crystals were pulverized in form of powder for the growth of Ga$_2$O$_3$ nanomaterials. The structure, morphology and composition of the products were studied mainly by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM).).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.12-12
• /
• 2010

Time dependence of the shift of the threshold voltage of amorphous hafnium-indium-zinc oxide (a-HIZO) has been reported under on-current stress condition. a-HIZO thin films were deposited on $SiO_2$/Si (100) by rf magnetron sputtering. XPS measurement indicates that the Hf metal cations in a-HIZO system after annealing process reduce oxygen vacancies by binding oxygen. It was found that the Hf metal cation can be effectively incorporated in the IZO thin films as a suppressor against both the oxygen deficiencies and the carrier generation in the ZnO-based system.

• 한국전기전자재료학회논문지
• /
• 제19권5호
• /
• pp.442-449
• /
• 2006

Electrical, optical, and structural properties of indium zinc oxide (IZO) films grown by a box cathode sputtering (BCS) were investigated as a function of oxygen flow ratio. A sheet resistance of $42.6{\Omega}/{\Box}$, average transmittance above 88% in visible range, and root mean spare roughness of $2.7{\AA}$ were obtained even in the IZO layers grown at room temperature. In addition, it is shown that electrical characteristics of the top-emitting organic light emitting diodes (TOLEDs) with the BCS grown-IZO top cathode layer is better than that of TOLEDs with DC sputter grown IZO top cathode, due to absence of plasma damage effect. Furthermore the effects of oxygen flow ratio in IZO films are investigated, based on x-ray photoelectron spectroscopy (XPS), ultra violet/visible (UV/VIS) spectro-meter, scanning electron microscopy (SEM), and atomic force microscopy (AFM) analysis results.

• 한국전기전자재료학회논문지
• /
• 제32권5호
• /
• pp.382-386
• /
• 2019

The alignment characteristics of liquid crystal (LC) molecules on a solution-derived lanthanum zinc oxide (LZO) film under ion-beam irradiation were demonstrated. Using the solution process, an LZO film was fabricated on the glass substrate and cured at $100^{\circ}C$. Afterwards, ion-beam irradiation was performed following the LC alignment method. Using this film, an LC cell was fabricated and the characteristics of the LC alignment were verified. Cross polarizing microscopy and the crystal rotation method were used to investigate the alignment state of the LC molecules on the LZO films. Furthermore, field emission scanning electron microscopy and X-ray photoelectron spectroscopy were used to explore the effect of the ion-beam irradiation on the LZO film. Through these, it was confirmed that the ion-beam irradiation induced surface modification, which demonstrated anisotropic physical and chemical surface characteristics. Due to this, uniform LC alignment was achieved. Finally, the residual DC and anchoring energy of the LC cell based on the LZO films were measured using a capacitance-voltage curve.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.249.2-249.2
• /
• 2015

Connecting two or more sub-cells is a simple and effective way of improving power conversion efficiency (PCE) of solar cells, and the theoretical efficiency of this tandem cell is known to reach 85~88% of the sum of the sub-cell's efficiencies. There are two ways of connecting sub-cells in the tandem structure, i.e. parallel and series connection. The parallel connection can increase the short circuit current (Jsc) and the series connection can increase the open circuit voltage (Voc). Although various tandem structures have been studied, the full use of incident light and optimization of cell efficiency is still limited. In this work, we designed series tandem solar cells consisting of lead sulfide (PbS) quantum dots/zinc oxide-based QDSC and zinc phthalocyanine (ZnPc)/C60-based small molecule OSCs. It is expected that the loss of the incident light is minimized because the absorption range of the PbS quantum dots and ZnPc is significantly different, and the Voc increases according to the Kirchhoff's law.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.351.1-351.1
• /
• 2014

In this study, we prepared the solution-based In-Ga-Zn oxide thin film transistors (IGZO TFTs) of multistacked active layer and characterized the gate bias instability by measuring the change in threshold voltage caused by stacking. The solutions for IGZO active layer were prepared by In:Zn=1:1 mole ratio and the ratio of Ga was changed from 20% to 30%. The TFTs with multistacked active layer was fabricated by stacking single, double and triple layers from the prepared solutions. As the number of active layer increases, the saturation mobility shows the value of 1.2, 0.8 and 0.6 (). The electrical properties have the tendency such as decreasing. However when gate bias VG=10 V is forced to gate electrode for 3000 s, the threshold voltage shift was decreased from 4.74 V to 1.27 V. Because the interface is formed between the each layers and this affected the current path to reduce the electrical performances. But the uniformity of active layer was improved by stacking active layer with filling the hole formed during pre-baking so the stability of device was improved. These results suggest that the deposition of multistacked active layer improve the stability of the device.

• 한국정보통신학회논문지
• /
• 제25권5호
• /
• pp.719-730
• /
• 2021

본 논문에서는 산화아연/탄소 테이프/산화아연의 대칭 구조를 갖는 ZCZ-NG라는 샌드위치형 산화아연(ZnO) 압전 에너지 하베스팅 소자를 제시한다. 고품질의 ZCZ-NG 소자를 제작하기 위해 전도성 양면 접착 탄소 테이프를 활용하였으며, 이는 매우 높은 피크 투 피크 전압(V_pp)을 발생시키는 ZCZ-NG 소자의 개발로 이어졌다. ZCZ-NG 소자의 크기, 산화아연 층의 두께 그리고 벤딩 변형률 변화에 따른 ZCZ-NG 소자의 출력 성능 변화를 측정, 분석하였다. 또한 제작된 ZCZ-NG 소자의 실효성 및 응용 가능성을 검증하기 위한 실험적인 센서 네트워크 테스트베드를 구축하였다. 상용 아두이노를 기반으로 한 송신, 수신 노드들로 이루어진 테스트베드에서 노드들은 각 노드에서 감지한 정보들을 무선으로 송수신한다. 본 연구에서 사용된 대칭 구조의 샌드위치형 ZCZ-NG 소자 제작 기술과 센서 네트워크와의 융합 연구가 앞으로 더 발전되어 사물인터넷 구현을 위한 자가발전 센서 네트워크 연구에 도움이 되길 바란다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.200-200
• /
• 2010

In recent times, metal oxide semiconductors thin films transistor (TFT), such as zinc and indium based oxide TFTs, have attracted considerable attention because of their several advantageous electrical and optical properties. There are many deposition methods for fabrication of ZnO-based materials such as chemical vapor deposition, RF/DC sputtering and pulsed laser deposition. However, these vacuum process require expensive equipment and result in high manufacturing costs. Also, the methods is difficult to fabricate various multicomponent oxide semiconductor. Recently, several groups report solution processed metal oxide TFTs for low cost and non vacuum process. In this study, we have newly developed solution-processed TFTs based on Ti-related multi-component transparent oxide, i. e., InTiO as the active layer. We propose new multicomponent oxide, Titanium indium oxide(TiInO), to fabricate the high performance TFT through the sol-gel method. We investigated the influence of relative compositions of Ti on the electrical properties. Indium nitrate hydrate [$In(NO^3).xH_2O$] and Titanium isobutoxide [$C_{16}H_{36}O_4Ti$] were dissolved in acetylacetone. Then monoethanolamine (MEA) and acetic acid ($CH_3COOH$) were added to the solution. The molar concentration of indium was kept as 0.1 mol concentration and the amount of Ti was varied according to weighting percent (0, 5, 10%). The complex solutions become clear and homogeneous after stirring for 24 hours. Heavily boron (p+) doped Si wafer with 100nm thermally grown $SiO_2$ serve as the gate and gate dielectric of the TFT, respectively. TiInO thin films were deposited using the sol-gel solution by the spin-coating method. After coating, the films annealed in a tube furnace at $500^{\circ}C$ for 1hour under oxygen ambient. The 5% Ti-doped InO TFT had a field-effect mobility $1.15cm^2/V{\cdot}S$, a threshold voltage of 4.73 V, an on/off current ratio grater than $10^7$, and a subthreshold slop of 0.49 V/dec. The 10% Ti-doped InO TFT had a field-effect mobility $1.03\;cm^2/V{\cdot}S$, a threshold voltage of 1.87 V, an on/off current ration grater than $10^7$, and a subthreshold slop of 0.67 V/dec.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.429-429
• /
• 2016

Organolead halide perovskite have attracted much attention over the past three years as the third generation photovoltaic due to simple fabrication process via solution process and their great photovoltaic properties. Many structures such as mesoporous scaffold, planar heterojunction or 1-D TiO2 or ZnO nanorod array structures have been studied to enhance performances. And the photovoltaic performances and carrier transport properties were studied depending on the cell structures and shape of perovskite film. For example, the perovskite cell based on TiO2/ZnO nanorod electron transport materials showed higher electron mobility than the mesoporous structured semiconductor layer due to 1-D direct pathway for electron transport. However, the reason for enhanced performance was not fully understood whether either the shape of perovskite or the structure of TiO2/ZnO nanorod scaffold play a dominant role. In this regard, for a clear understanding of the shape/structure of perovskite layer, we applied anodized aluminum oxide material which is good candidate as the inactive scaffold that does not influence the charge transport. We fabricated vertical one dimensional (1-D) nanostructured methylammonium lead mixed halide perovskite (CH3NH3PbI3-xClx) solar cell by infiltrating perovskite in the pore of anodized aluminum oxide (AAO). AAO template, one of the common nanostructured materials with one dimensional pore and controllable pore diameters, was successfully fabricated by anodizing and widening of the thermally evaporated Al film on the compact TiO2 layer. Using AAO as a scaffold for perovskite, we obtained 1-D shaped perovskite absorber, and over 15% photo conversion efficiency was obtained. I-V measurement, photoluminescence, impedance, and time-limited current collection were performed to determine vertically arrayed 1-D perovskite solar cells shaped in comparison with planar heterojunction and mesoporous alumina structured solar cells. Our findings lead to reveal the influence of the shape of perovskite layer on photoelectrical properties.