• 공업화학
• /
• 제33권4호
• /
• pp.402-407
• /
• 2022

실험계획법을 이용하여 MOF-5 합성공정의 최적화에 대한 연구를 수행하였다. 먼저 전구체의 농도를 최적화 하기 위하여 혼합물 설계법을 이용하였다. 합성에 사용되는 세 가지 전구체인 terephthalic acid, zinc acetate dihydrate, N,N-dimethylformamide의 농도비를 extreme vertices design methods로 최적화 하였다. MOF-5 합성을 위한 최적의 농도는 1 mol : 2.7 mol : 40 mol로 예측되었다. 이후, 온도, 시간 및 교반 속도와 같은 합성 반응 조건이 합성에 미치는 영향을 분석하기 위해 다단계 요인 설계법을 사용하였다. 수행된 통계 분석에 따라 교반 속도는 후속 연구에서 제외되었다. 합성시간과 온도를 고려한 합성 공정 최적화는 중앙 조성 설계법을 이용하였다. 13번의 합성 실험을 통해 도출된 2차 모델 방정식을 이용하여 결과를 추정하였다. 설계에 사용된 모델에 의하면 119 ℃ 및 10.4 h 조건에서 합성된 MOF-5가 최대의 결정화도를 가지는 것으로 예측되었다.

• Advances in nano research
• /
• 제3권3호
• /
• pp.123-131
• /
• 2015

The unintentionally doped and bismuth (Bi) doped zinc oxide (ZnO) films were prepared by spray pyrolysis at $450^{\circ}C$ with zinc acetate and bismuth nitrate precursor. The n-type conduction with concentration $6.13{\times}10^{16}cm^{-3}$ can be observed for the unintentionally doped ZnO. With the increasing of bismuth nitrate concentration in precursor, the p-type conduction can be observed. The p-type concentration $4.44{\times}10^{17}cm^{-3}$ can be achieved for the film with the Bi/Zn atomic ratio 5% in the precursor. The photoluminescence spectroscopy with HeCd laser light source was studied for films with different Bi doping. The photocatalytic activity for the unintentionally doped and Bi-doped ZnO films was studied through the photodegradation of Congo red under UV light illumination. The effects of different Bi contents on photocatalytic activity are studied and discussed. Results show that appropriate Bi doping in ZnO can increase photocatalytic activity.

• 한국산업보건학회지
• /
• 제9권1호
• /
• pp.156-172
• /
• 1999

Potential chemical hazards encountered in painting operation of four shipyards and a ship-repair shop were investigated through the material safety data sheets (MSDS). Material safety data sheets (MSDS) for 307 paints, 50 thinners and 34 binders were collected and reviewed. It was shown that various organic solvents such as aromatic hydrocarbons, aliphatic hydrocarbons, ketones, alcohols, glycols, glycol ether acetates and esters were contained in painting materials. Of these solvents, xylene was found in the largest number of painting materials. sixty percent of the thinners contained xylene in the contents of 20-100%. Other most frequently found solvents were 1-methoxypropanol, 1-methoxypropyl acetate, n-butanol, methyl isobutyl ketone, toluene, isopropanol, and n-butyl acetate, etc. Glycol ethers such as 2-methoxyethanol (2-ME), 2-methoxyethyl acetate (2-MEA), 2-ethoxyethanol (2-EE), 2-ethoxyethyl acetate (2-EEA) and 2-butoxyethanol (2-BA) were regarded as having the potential to cause adverse reproductive effects, embryotoxic effect and hematotoxic effects, and were found in some epoxy panting materials. Coal tar pitch was included in some paints(13%) where polynuclear aromatic hydrocarbons (PAHs) could be contaminated. Inorganic pigments such as lead chromate and zinc potassium chromate were found in some paints (8%). The epoxy resin based paints, which may contain isocyanates such as toluene diisocyanates and hexamethylene diisocyanates causing potential sensitization and asthma to upper respiratory organ, were mostly used in the shipyards. The constituents in the MSDS were significantly different from the results analyzed using gas chromatography/mass detector: minor constituents or impurities were omitted in many MSDS. In conclusion, xylene was the most frequent organic solvent in painting materials, and glycol ethers, including 2-ME, 2-MEA, 2-EE, 2-EEA and 2-BA, were found some products. Also, painting workers may be exposed to PAHs, lead, chromate, isocyanates, organic tin and other various chemicals. The compositions of chemicals in painting materials were variable significantly, and the hazards were changed. These facts should be considered in environmental monitoring and control of the hazards.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.167-167
• /
• 2012

Aluminium-zinc-tin oxide (AZTO) 박막 트랜지스터는 Spin-coating 방법으로 제작되었다. AZTO용액의 용매는 2-Methoxyethanol, 용질은 각각 Aluminium nitride, Zinc acetate dihydrate, Tin chloride가 사용되어 제작되었다. 용액의 안정성을 위해서 미량의 Mono ethyl amine이 첨가되었다. 용액의 Zn:Sn의 몰 비율은 1 : 1로 고정 되었으며 Al의 mole비를 다양하게 늘리면서 실험을 진행하였다. 이렇게 만들어진 AZTO용액은 3,000 rpm으로 30초간 Spin-coating하였으며 이후 Furnace system을 통하여 $500^{\circ}C$의 온도로 1시간 동안 후열처리 공정을 진행하였다. AZTO박막을 활성층으로 제작된 박막 트랜지스터는 Al의 비율이 늘어남에 따라 처음엔 이동도가 증가하였으나 이후 이동도가 낮아지며 소자특성이 나빠지는 것을 보였다. 이러한 현상의 원인을 알아보고자 물리적, 전기적, 광학적 분석을 통해서 Al양의 변화가 박막트랜지스터 구동에 미치는 영향을 해석하였다. 먼저 AZTO용액은 열중량측정/시차열분석법(Thermo Gravimetry/Differential Thermal Analysis)을 이용하여 spin-coating 이후 후 열처리 온도 결정 및 박막의 변화를 관찰하였으며, X-선 분광(X-ray photoelectron spectroscopy)을 이용하여 박막의 조성 및 전자구조의 변화를, 타원분광해석법(Spectroscopic Ellipsometry)분석을 통하여 밴드 갭과 전도대 이하 밴드 갭 내에 존재하는 결함상태변화를 관찰하였다. AZTO 박막 내의 Al양을 조절하는 것은 박막내의 에너지 준위의 변화를 야기하고 그로인해 박막트랜지스터의 특성을 변화킨다는 결과를 도출하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.374.1-374.1
• /
• 2016

Copper and zinc are well known elements with antibacterial effect. So in this research, Cu and Zn (CZ) nanofibers (NFs) were fabricated by electrospinning method using polyvinylpyrrolidone (PVP) for adjusting viscosity. The CZ/PVP precursor solutions were prepared with copper sulfate pentahydrate, and zinc acetate dihydrate. Distilled water was used for solvent and PVP was used to regulate the viscosity of precursor solution. The CZ/PVP NF composites were obtained by electrospinning method using the precursor solution. The average diameter of obtained CZ/PVP NFs was determined by optical microscopy using Motic image plus 2.0 program and was found to be 490 nm. The chemical environment of the obtained CZ/PVP NF composites was investigated with X-ray photoelectron spectroscopy (XPS). After heating the obtained CZ/PVP NF composites at 353 K, the solvent was removed. The characteristic C 1s, Cu 2p, and Zn 2p core level XPS peaks were observed. After calcination the CZ/PVP NF composites at 873 K in Ar environment for 5 hrs, PVP was decomposed at this temperature and CZ NF was obtained. This was confirmed by decreasing the intensity of C 1s.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.236.2-236.2
• /
• 2015

The copper-zinc(Cu-Zn) nanofiber was prepared by electrospinning method. The Cu/PVP (polyvinylpyrrolidone) and Zn/PVP precursor solutions were prepared by dissolution of copper sulfate and zinc acetate in methanol, respectively. The PVP was used to control the viscosity of the precursor solutions. The optimized ratio for the Cu/PVP and Zn/PVP nanofibers was determined separately. Then the suitable ratio of the precursor solutions was applied for fabrication of Cu/Zn/PVP nanofiber. For the electrospinning method, the precursor solutions were filled in a syringe. The distance between metallic needle on the syringe and collector was fixed at 16 cm and the voltage was applied on the tip was 13.0 kV. And the as-spun nanofiber was heated at 353K for removal of residual solvent. Then the heated nanofibers were calcined at 973K to decompose PVP. The obtained Cu, Zn, and Cu-Zn nanofibers were investigated with X-ray photoelectron spectroscopy (XPS) for the chemical properties, scanning electron microscopy (SEM) for the morphologies, and X-ray diffraction (XRD) to characterize the crystallinity and phase of nanofibers.

• 한국결정성장학회지
• /
• 제14권5호
• /
• pp.187-192
• /
• 2004

We try to use isopropanol which has low boiling point to prepare ZnO thin films at low temperature. ZnO thin films were prepared by sol-gel spin-coating method using zinc acetate dehydrate-isopropanol-monoethanolamine (MEA) solution. The c-axis preferred orientation and optical properties of ZnO films with preheating temperature have been investigated. ZnO thin films were preheated at 200 to $300^{\circ}C$ with an interval of $25^{\circ}C$ and post-heated at $650^{\circ}C$. The ZnO film preheated at $275^{\circ}C$ and post-heated at $650^{\circ}C$ was highly oriented along c-axis (002) plane, and the surface with homogeneous and dense microstructures was formed having nano-sized grains. The optical transmittance was above 90 % in the visible range and exhibited absorption edges at 368 nm wavelength.

• 한국전기전자재료학회논문지
• /
• 제19권5호
• /
• pp.457-460
• /
• 2006

Y doped zinc oxide (YZO) thin films were deposited on F doped $SnO_2$ (FTO) glass substrate by sol-gel method using the spin-coating system. A homogeneous and stable solution was prepared by dissolving acetate in the solution added diethanolamine as sol-gel stabilizer. YZO films were obtained after preheated on the hot-plate for 5minute before each coating; the number of coating was 3 times. After the coating of last step, annealing of YZO films performed at $450^{\circ}C$ for 30 minute. In order to confirming of a ultraviolet ray interruption and down-conversion effects, optical properties of YZO films, transmission spectrum and fluorescent spectrum were used. Also, for understanding the obtained results by experiment, the elestronic state of YZO was calculated using the density functional theory The results obtained by experiment were compared with calculated structure. The detail of electronic structure was obtained by the discrete variational Xa (DV-Xa) method, which is a sort of molecular orbital full potential method. The density of state and energy levels of dopant element were shown and discussed in association with optical properties.

• 한국세라믹학회지
• /
• 제41권2호
• /
• pp.136-142
• /
• 2004

출발물질로 zinc acetate dihydrate(Zn($CH_3$COO)$_2$$.$2$H_2O$)를 사용하였고, 이 물질을 isopropanol(($CH_3$)$_2$CHOH)-monoethanolamine(MEA:H$_2$NCH$_2$C$H_2O$H) 용액에 용해하여 균일하고 안정한 sol을 만들었다. Sol-gel spin-coating 법에 의해 ZnO 박막을 제조시 예열 온도에 따른 박막의 c-축 배향성과 그 물리적 특성을 조사하였다. c-축으로의 성장은 예열 온도의 변화에 따라 차이를 보였으며. 275$^{\circ}C$에서 예열 후 $650^{\circ}C$에서 최종 열처리한 ZnO 박막은 XRD 측정결과 기판에 수직한 (002) 방향으로 강한 배향성을 나타내었다 200∼30$0^{\circ}C$에서 예열 후, $650^{\circ}C$에서 최종 열처리한 ZnO 박막은 UV-vis측정결과 가시광선 영역에서 온도에 따른 투과도의 변화를 보이지만 평균 85% 이상의 높은 투과도를 보였다. 또한 370nm 부근에서 흡수단을 나타내었으며, 광학적 밴드갭은 약 3.22 eV로 나타났다. 발광방출(PL) 측정결과, 황색(620nm, 2.0 eV)발광이 관찰되어, 무기발광 소자로의 응용 가능성을 나타내었다.

• 한국결정성장학회지
• /
• 제18권1호
• /
• pp.50-55
• /
• 2008

졸-겔 공정을 이용하여 유리기판 위에 Al-doped ZnO(AZO) 박막을 제조하였고, AZO 박막의 특성에 대하여 Al 전구체 종류 및 post-annealing 온도가 미치는 영향에 대하여 고찰하였다. AZO 박막 제조용 졸은 zinc acetate, EtOH, MEA 등을 사용하여 제조하였고, Al doping 을 위한 전구체로는 aluminum nitrate 와 aluminum chloride 를 사용하였다. Sol 내의 Zn 농도는 0.5 mol/l 로 하였고, Al doping 양은 Zn 대비 1 at%로 고정하였다. 유리기판 위에 졸을 spin-coating 한 후 $550^{\circ}C$에서 2 시간 동안 열처리한 후, $N_2$와 $H_2$의 비가 9 : 1인 환원 분위기 내에서 $300^{\circ}C,\;400^{\circ}C,\;500^{\circ}C$인 온도에서 2시간 동안 post-annealing을 진행하였다. 제조된 AZO 박막의 구조적, 전기적, 광학적 특성은 XRD, FE-SEM, AFM, Hall effect measurement system 및 UV-Visible spectroscopy를 이용하여 분석하였다. Al 전구체로서 aluminum nitrate 를 사용한 경우가 aluminum chloride 를 사용하여 제조한 AZO 박막보다 우수한 광학적, 전기적 특성을 나타내었으며, post-annealing 온도가 증가함에 따라 비저항과 투과율은 감소하였다. $500^{\circ}C$에서 post-annealing한 AZO 박막의 전기비저항 값은 $2{\times}10^{-3}{\Omega}{\cdot}cm$이었고, 투과율은 $300^{\circ}C$에서 91%로 가장 높게 나타났다.