• 동력기계공학회지
• /
• 제18권4호
• /
• pp.43-51
• /
• 2014

In this paper, transient temperature and vibration characteristics of a brushless DC (BLD(c) motor are studied for external load (165W~495W) and rotational speed (2000 rpm~4000 rpm). For experiment, a simple measurement system is developed to allow a change in load and speed for measuring transient temperature and vibration simultaneously. Temperature and vibration were also measured under the conditions of natural convection and forced convection. Vibrations in the directions of x-axis (#Ch1), y -axis (#Ch2) and z -axis (#Ch3) were obtained by three accelerometers and temperature was obtained by a thermo-couple with respect to time until the motor is steady. Experimental results show that the amplitude of vibration is higher in the order of z-axis (#Ch3), x -axis (#Ch1) and y-axis (#Ch2) and the amplitude of vibration at the forced convection conditions is 10.6% to 17.8% lower than that of vibration at the natural convection. However, the ratio of the vibration value is similar on average regardless of external convection condition.

• 대한의용생체공학회:의공학회지
• /
• 제17권4호
• /
• pp.449-458
• /
• 1996

Most of the conventional electrocardiowaphs foil to detect signals other than P-QRS-T due to the limited SNR and bandwidth. High-resolution electrocardiography(HRECG) provides better SNR and wider bandwidth for the detection of micro-potentials with higher frequency components such as vontricular late potentials(LP). We have developed a HRECG using uncorrected XYZ lead for the detection of LPs. The overall gain of the amplifier is 4000 and the bandwidth is 0.5-300Hz without using 60Hz notch filter. Three 16-bit A/D converters sample X, Y, and Z signals simultaneously with a sampling frequency of 2000Hz. Sampled data are transmitted to a PC via a DMA-controlled, optically-coupled serial communication channel. In order to further reduce the noise, we implemented a signal averaging algorithm that averaged many instances of aligned beats. The beat alignment was carried out through the use of a template matching technique that finds a location maximizing cross-correlation with a given beat tem- plate. Beat alignment error was reduced to $\pm$0.25ms. FIR high-pass filter with cut-off frequency of 40Hz was applied to remove the low frequency components of the averaged X, Y, and Z signals. QRS onset and end point were determined from the vector magnitude of the sigrlaIL and some parameters needed to detect the existence of LP were estimated. The entire system was designed for the easy application of the future research topics including the optimal lead system, filter design, new parameter extraction, etc. In the developed HRECG, without signal averaging, the noise level was less than 5$\mu$V$_rms RTI$. With signal averaging of at least 100 beats, the noise level was reduced to 0.5$\mu$V$_rms RTI$, which is low enough to detect LPs. The developed HRECG will provide a new advanced functionality to interpretive ECG analyzers.

• 한국멀티미디어학회논문지
• /
• 제12권8호
• /
• pp.1089-1098
• /
• 2009

최근에 인간컴퓨터 상호작용 분야에서 사용자의 시선 위치를 파악하여 더욱 편리한 입력 장치를 개발하고자 하는 연구가 많이 진행되고 있다. 기존의 대부분 연구들은 큰 모니터를 사용하는 컴퓨터 환경에서 시선 추적 시스템을 개발하였다. 최근 이동단말기의 사용 증대로 이동 중에 시선 추적에 의한 단말기 제어의 필요성이 증대되고 있다. 이에 본 연구에서는 이동형 컴퓨터 (Ultra-Mobile PC) 및 컴퓨터 내장 카메라를 이용하여 사용자의 얼굴을 추적하고, 얼굴내의 특징점의 위치를 능동외관모델 (Active Appearance Model)을 기반으로 추적하는 연구를 수행하였다. 본 논문의 독창성은 기존 연구와는 달리 소형 화면을 가지는 이동 단말기에서 사용자의 시선 위치를 추적할 수 있는 방법을 제안한 점과 정밀한 얼굴 특징점 검출을 위하여 능동외관모델을 사용한 점이다. 또한 사용자의 초기 캘리브레이션시 얻어진 특징값을 기반으로, 입력 특징값들을 정규화 함으로써, Z거리에 따라 시선 위치 정확도가 영향을 받지 않는다는 점이다. 실험결과, 약 1.77도의 시선 오차를 발생하였으나, 추가적인 얼굴 움직임에 의한 마우스 움직임 기능으로 이러한 시선 오차는 더욱 줄일 수 있음을 알 수 있었다.

• 한국정보통신학회논문지
• /
• 제12권11호
• /
• pp.1923-1932
• /
• 2008

무인 운반설비의 자동화 시스템 개발의 한 부분으로써 여러 Vision 센서 중 레이저 센서를 이용하여 작업 공간상에 있는 판재류와 코일류의 경계부분을 인식한다. 다음으로 인식한 물체의 경계를 이용하여 3차원 공간상의 위치 좌표를 추출하여 무인크레인에 이동해야할 위치 좌표를 전달한다. 본 연구에서는, 첫 번째 레이저 센서를 이용한 물체의 경계 추출, 두 번째 레이저 센서의 z축 기울기 각 추출, 세 번째 인식한 경계를 이용하여 물체의 2차원 위치좌표 추출, 네 번째 레이저 센서를 이용하여 판재와 코일의 판별, 다섯 번째 물체 판별의 결과에 따른 판재 와 코일의 3차원 위치좌표 추출을 목적으로 한다. 본 연구의 결과는 무인 운반설비의 자동화 시스템 개발에 상당한 도움이 될 것으로 기대된다.

• 방사선산업학회지
• /
• 제9권3호
• /
• pp.153-159
• /
• 2015

Reliability of printed circuit board (PCB), which is based on high integrated circuit technology, is having been important because of development of electric and self-driving car. In order to answer these demand, automated X-ray inspection (AXI) is best solution for PCB non-destructive test. PCB is consist of plastic, copper, and, lead, which have low to high Z-number materials. By using dual energy X-ray imaging, these materials can be inspected accurately and efficiently. Dual energy X-ray imaging, that have the advantage of separating materials, however, need some solution such as energy separation method and enhancing efficiency because PCB has materials that has wide range of Z-number. In this work, we found out several things by analysis of X-ray energy spectrum. Separating between lead and combination of plastic and copper is only possible with energy range not dose. On the other hand, separating between plastic and copper is only with dose not energy range. Moreover the copper filter of high energy part of dual X-ray imaging and 50 kVp of low energy part of dual X-ray imaging is best for efficiency.

• Corrosion Science and Technology
• /
• 제18권5호
• /
• pp.212-219
• /
• 2019

This paper reviews recent approaches to develop composite polymer-containing coatings by plasma electrolytic oxidation (PEO) using various low-molecular fractions of superdispersed polytetrafluoroethylene (SPTFE). The features of the unique approaches to form the composite polymer-containing coating on the surface of MA8 magnesium alloy were summarized. Improvement in the corrosion and tribological behavior of the polymer-containing coating can be attributed to the morphology and insulating properties of the surface layers and solid lubrication effect of the SPTFE particles. Such multifunctional coatings have high corrosion resistance ($R_p=3.0{\times}10^7{\Omega}cm^2$) and low friction coefficient (0.13) under dry wear conditions. The effect of dispersity and ${\xi}$-potential of the nanoscale materials ($ZrO_2$ and $SiO_2$) used as electrolyte components for the plasma electrolytic oxidation on the composition and properties of the coatings was investigated. Improvement in the protective properties of the coatings with the incorporated nanoparticles was explained by the greater thickness of the protective layer, relatively low porosity, and the presence of narrow non-through pores. The impedance modulus measured at low frequency for the zirconia-containing layer (${\mid}Z{\mid}_{f=0.01Hz}=1.8{\times}10^6{\Omega}{\cdot}cm^2$) was more than one order of magnitude higher than that of the PEO-coating formed in the nanoparticles-free electrolyte (${\mid}Z{\mid}_{f=0.01Hz}=5.4{\times}10^4{\Omega}{\cdot}cm^2$).

• 아시안잔디학회지
• /
• 제10권1호
• /
• pp.1-11
• /
• 1996

Fifty accessions in Zoysia species and forty-one hybrid lines were evaluated in order to detect analyze the genectic variation of Zoysiagrasses and to obtain the basic information for breeding. 1.Plant height ranged from 13 to 34.5cm, leaf length from 7 to 26cm, leaf width from 2 to 7mm, and first leaf height from 1.1 to 8.5cm 2. The correlations among plant height, leaf length and first-leaf height were high, but leaf Width was correlated only With leaf length. 3. Stolon length was varied from 10 to 108cm, number of stolons from 12 to 53, internode length from 2 to 6.1cm and coverage percentage from 10 to 90%. 4.There were correlation among stolen length, number of stolons, internode length and coverage percentage except between stolen and internode length. 5.M1J and MC2 showed the highest level in stolen length, number of stolons and coverage percentage. Therefore they will be the best breeding materials for the purpose of fast covering. 6.According to the analysis on October 26, 1995, yellow color-change rate of leaves ranged from 5 to 85%, red color-change from 0 to 75% and sum of yellow and red change from 20 to 95%. Speciallty M2M1 and FL-41 kept green color untill early December, indicating that they had the late dormancy. 7. Visual assessment of stolon length and number of stolons, showed similar tendency With actually measured data. 8. Shoot density was very high in M2M1 and S2, and showed negative correlation with leaf width. 9. It is known in Korea that the darker green color of lawngrass is, the better it looks. There were 11 lines with dark green color leaves such as J 85-10, Meyer in Z. japonira, one asacession in Z. matrella and M2M1, M2S8, JM2, 55C2 in hybrid lines.

• Investigative Magnetic Resonance Imaging
• /
• 제25권3호
• /
• pp.141-155
• /
• 2021

Purpose: To develop a 3D magnetic resonance fingerprinting (MRF) method for application in high resolution knee cartilage PD, T₁, T₂ mapping. Materials and Methods: A novel 3D acquisition trajectory with golden-angle rotating radial in k_xy direction and interleaved echo planar imaging (EPI) acquisition in the k_z direction was implemented in the MRF framework. A centric order was applied to the interleaved EPI acquisition to reduce Nyquist ghosting artifact due to field inhomogeneity. For the reconstruction, singular value decomposition (SVD) compression method was used to accelerate reconstruction time and conjugate gradient sensitivity-encoding (CG-SENSE) was performed to overcome low SNR of the high resolution data. Phantom experiments were performed to verify the proposed method. In vivo experiments were performed on 6 healthy volunteers and 2 early osteoarthritis (OA) patients. Results: In the phantom experiments, the T₁ and T₂ values of the proposed method were in good agreement with the spin-echo references. The results from the in vivo scans showed high quality proton density (PD), T₁, T₂ map with EPI echo train length (N_ETL = 4), acceleration factor in through plane (R_z = 5), and number of radial spokes (N_spk = 4). In patients, high T₂ values (50-60 ms) were seen in all transverse, sagittal, and coronal views and the damaged cartilage regions were in agreement with the hyper-intensity regions shown on conventional turbo spin-echo (TSE) images. Conclusion: The proposed 3D MRF method can acquire high resolution (0.5 mm³) quantitative maps in practical scan time (~ 7 min and 10 sec) with full coverage of the knee (FOV: 160 × 160 × 120 mm³).

• 디지털융복합연구
• /
• 제18권12호
• /
• pp.325-333
• /
• 2020

이 연구는 대학병원에 근무하는 간호사를 대상으로 그릿, 건강지각과 건강증진행위의 관계에서 자기효능감의 매개효과를 파악하고 건강증진행위를 향상시키는데 기초자료를 제공하기 위해 시도되었다. D소재 일개 대학병원 간호사 242명을 대상으로 구조화된 설문지를 이용하여 자료수집하였다. 건강증진행위는 그릿(r=.29, p=<.001), 건강지각(r=.33, p=<.001), 자기효능감(r=.40, p=<.001)과 양의 상관관계를 나타냈으며 통계적으로 유의하였다. 그릿이 건강증진행위에 미치는 영향에 있어서 자기효능감이 완전매개효과(Z=4.41, p<.001)가 있는 것으로 나타났으며 건강지각이 건강증진행위에 미치는 영향에 있어서 자기효능감이 부분매개효과(Z=3.36, p<.001)가 있는 것으로 나타났다. 이에 따라 간호사의 그릿, 자기효능감, 건강지각에 영향을 미치는 요인을 확인하여 건강증진 행위를 향상시키는 중재방안을 마련해야 할 것이다.

• 대한지역사회영양학회지
• /
• 제26권1호
• /
• pp.1-11
• /
• 2021

Objectives: This study was conducted to assess the eating behavior, growth, and dietary practices of children aged 3~5 years living in the Seoul and Gyeonggi Provinces. Methods: Self-administered questionnaires were completed by 237 mothers of preschool children between April and June 2018. Z-scores for weight-for-age, height-for-age, and BMI-for-age were calculated to determine the children's growth status. Dietary practices were evaluated using the nutrition quotient for Korean preschoolers (NQ-P). Results: In our study, 29.5% of children were in the eating-small-amounts group, 46.8% of children were in the neophobic behavior group, and 61.2% of children were in the refusal-of-specific food group. Specific foods found to have a high frequency of rejection are listed in descending order as follows: shellfish, soy, mushroom, shrimp, vegetables, milk, eggs, yogurt, seaweed, meat, fruits, and fish. The eating-small-amounts group had lower Z-scores for weight-for-age, height-for-age, and BMI-for-age than the non-picky eaters' group. Compared to the non-picky eaters' group, the eating-small-amounts group of picky eaters had lower scores on the moderation and environment items of the NQ-P, the neophobic behavior group had lower scores on the balance and environment items of the NQ-P, and the refusal-of-specific food group had lower scores on the balance, moderation, and environment items of the NQ-P. Conclusions: Children classified with picky eating behavior had lower growth and development, lower diet diversity, less balanced food intake, and had greater difficulty in abstaining from eating unhealthy foods than non-picky eaters. Therefore, a lot of patience and intensive efforts are needed to encourage children to encounter, experience, and accept unfamiliar food. It is more effective to provide eating behavior guidance by gently encouraging children, than by being strict and forceful. Besides, since the eating behavior of children is influenced maximally by the dietary lifestyle at their homes, it is important to ensure that a healthy dietary lifestyle is maintained at home.