• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2013년도 추계학술대회 논문집
• /
• pp.48-49
• /
• 2013

In this paper, the four switches three-phase Z-source rectifier is studied. The conventional three-phase four switches rectifier can only either perform buck or boost operation, distortion and unbalance of the input current are serious. Therefore, we proposed the four switches three-phase Z-source rectifier which can realize buck function simply by applying the Z-impedance network. We will verify characteristics of Z-network by the simulation and experiment.

• Journal of Electrical Engineering and Technology
• /
• 제7권5호
• /
• pp.714-723
• /
• 2012

A new Z-source inverter (ZSI) topology is developed to improve voltage boost ability. The proposed topology is modified from the switched inductor topology by adding some more inductors and diodes into inductor branch to the conventional Z-source network. The modulation methods developed for the conventional ZSI can be easily utilized in the proposed ZSI. The proposed ZSI has an ability to obtain a higher voltage boost ratio compared with the conventional ZSI under the same shoot-through duty ratio. Since a smaller shoot-through duty ratio is required for high voltage boost, the proposed ZSI is able to reduce the voltage stress on Z-source capacitor and inverter-bridge. Theoretical analysis and operating principle of the proposed topology are explicitly described. In addition, the design guideline of the proposed Z-source network as well as the PWM control method to achieve the desired voltage boost factor is also analyzed in detail. The improved performances are validated by both simulation and experiment.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.1-9
• /
• 2015

This study presents a novel transformer isolated parallel connected quasi Z-source (qZ-source) full-bridge DC-DC converter that uses a coupled inductor in both the qZ-source network and output filter inductor. Unlike traditional voltage-fed or current-fed converters, the proposed converter can be open- and short-circuited without damaging switching devices. Therefore, the desired buck and boost functions can be achieved and converter reliability can be significantly improved. All the bulky inductors in the qZ-source network and output filter can also be minimized with the proposed inductor structures. A 4 kW prototype DC-DC converter is built and tested to verify the performance of the proposed converter.

• 전력전자학회논문지
• /
• 제18권2호
• /
• pp.123-130
• /
• 2013

This paper proposes the switched trans Z-source inverter(STZSI) which combined the characteristics of the trans Z-source inverter(TZSI) and the switched inductor Z-source inverter(SLZSI). The proposed STZSI has the same performance compared with the SLZSI which is improved the voltage boost performance of the conventional typical X-shaped ZSI, and it has advantage that circuit structure of Z-impedance network is more simple. And, in order to step up the voltage boost factor under the condition of the same duty ratio, unlike the SLZSI adding the inductors and diodes, the proposed method is dune by changing the turn ratio of trans primary winding of Z-impedance network. To confirm the validity of the proposed method, PSIM simulation and a DSP(TMS320F28335) based experiment were performed using trans with turn ratio 1 and 2 under the condition of the input DC voltage VI=50V, duty ratio D=0.1 and D=0.15. As a result, under the same input/ouput condition, the inverter arm voltage stress of the proposed method is reduced to about 15%-22% as compared with typical X-shaped ZSI, and the elements in Z-impedance network of the proposed method is reduced as compared with the SLZSI.

• 전력전자학회논문지
• /
• 제18권1호
• /
• pp.91-102
• /
• 2013

This paper proposes the improved LCCT(Inductor-Capacitor-Capacitor-Trans) Z-source DC-DC converter (Improved LCCT ZSDC) which can generate the bipolar output voltages according to duty ratio D. The proposed converter has the characteristic and structure of Quasi Z-source DC-DC converter(Quasi ZSDC) and conventional LCCT Z-source DC-DC converter(LCCT ZSDC). To confirm the validity of the proposed method, PSIM simulation and a DSP based experiment were performed for each converter. In case which the input DC voltage is 70V, the bipolar output DC voltage of positive 90V and negative 50V could generate. Also, as comparison result of the capacitor voltage ripple in Z-network and the input current under the same condition for each converter, the voltage stress and the capacitor voltage in Z-network of the proposed method were lower compared with the conventional methods. Finally, the efficiency for each method was investigated according to load variation and duty ratio D.

• 한국조경학회지
• /
• 제43권3호
• /
• pp.101-113
• /
• 2015

본 연구는 바람통로의 세밀도와 편이성을 향상시켜 도시 녹지계획 활용도를 높이는 것을 목적으로 한다. 이를 위해 유체역학적 거칠기 특성을 나타내는 거칠기길이($z_0$)로부터 바람통로 네트워크 추출기법을 제안하였다. 지적필지 단위로 산출된 $z_0$에 IDW, Spline, Kriging 내삽기법을 적용해 표면이 연속적인 수치거칠기길이모델(DZoM)을 생성한 후 수계망 추출 기법을 적용해 바람통로 네트워크를 산출하였다. 내삽기법 적용 결과들을 비교하여 가장 적합한 내삽 기법을 정하고 산출된 바람통로와 토지피복 및 지표온도의 공간적 관계를 분석하였다. 연구결과 DZoM 산출기법 중 Kriging 기법의 적용성이 IDW 및 Spline 기법보다 우수한 것으로 나타났다. Kriging 기법을 이용하여 선형 추출한 바람통로 네트워크(Type B)와 Landsat-7 ETM+에서 산출한 여름철과 겨울철 야간 지표온도 분포를 비교한 결과는 공간적 일치도가 높았다. 주목할 부분으로 산출된 바람통로의 흐름이 도시의 야간 열 부하들을 완화하는 것으로 보인다. 추출된 바람통로 네트워크 사상들(features)에 대한 엄밀한 평가와 개선이 수행된다면 녹지계획 실무에 효과적으로 활용될 수 있을 것이다. 이를 위해서는 (1) 거칠기길이 개선, (2) 녹지계획 목적에 맞는 바람통로의 해석 및 편집, (3) 분절된 바람통로 네트워크 연결, (4) 관련 자료의 상세한 구축 및 무결성 확보 등이 선행되어야 할 것이다. 제안된 바람통로 네트워크의 녹지계획 적용을 위해 향후 연구범위를 수도권으로 확장할 계획이다.

• 한국정보과학회:학술대회논문집
• /
• 한국정보과학회 2011년도 한국컴퓨터종합학술대회논문집 Vol.38 No.1(B)
• /
• pp.163-166
• /
• 2011

정형명세 언어인 Z는 상태기반의 명세언어로써 시스템의 기능성을 명세하고 검증하기 좋은 장점을 가지고 있다. 또한 Z에서 제공하는 스키마를 이용하여 복잡한 구조의 상태를 나타내기에 용이하다. 하지만 2개 이상의 시스템으로 구성된 네트워크 상의 통신을 나타내기가 힘든 단점이 있다. 본 논문에서는 Z를 이용하여 네트워크 프로토콜을 명세하기 위한 프레임워크를 제시하고 사례연구를 통해 적용가능성을 살펴본다. 본 연구결과를 토대로 네트워크로 구성된 안전 필수 시스템의 명세 가이드라인을 제시한다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.223-224
• /
• 2011

This paper presents the method to design the inductor and capacitor value considering the ripple component that may be generated by three operating states of the Quasi Z source inverter at the impedance network. Based on the analysis of each operation mode, the equations of the capacitor voltage and inductor current are derived. In order to simplify the design processing, design equations of the impedance network are derived where the capacitor voltage and inductor current are lineared. The validity of the design method is verified with the simulation result using PSIM.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1195-1202
• /
• 2017

This paper presents a novel topology named a modified capacitor-assisted Z-source inverter (MCA-ZSI) based on the traditional ZSI. The impedance network of the proposed MCA-ZSI consists of two symmetrical cells coupled with two capacitors with an X-shape structure, and each cell has two inductors, two capacitors, and one diode. Compared with other topologies based on switched ZSI with the same number of components used at impedance network, the proposed topology provides higher boost ability, lower voltage stress across inverter switching devices, and lower capacitor voltage stress. The improved performances of the proposed topology are demonstrated in the simulation and experimental results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.203-204
• /
• 2012

This paper presents the method to design the inductor and capacitor value considering the ripple component that may be generated by three operating states of the Quasi Z-source inverter at the impedance network. Based on the analysis of each operation mode, the equations of the capacitor voltage and inductor current are derived. In order to simplify the design processing, design equations of the impedance network are derived where the capacitor voltage and inductor current are lineared. The validity of the design method is verified with the simulation result using PSIM and experimental result using 32-bit DSP.