• 한국재료학회지
• /
• 제8권6호
• /
• pp.505-512
• /
• 1998

플라즈마 용사법을이용하여 AISI 316 스테인레스 금속모재에 0.1mm 두께의 $NiCrAlCoY_{2}O_{3}$금속 결합층과 0.3mm 두께의 $ZrO_{2}(8wt%Y_{2}O_3$) 세라믹층으로 구성된 이층 단열코팅층을 제조하였다. 코팅층의 미세조직, 금속결합층의 산화를 고찰하였으며, $900^{\circ}C$에서 등은 시험과 열반복시험 후, 접합강도시험을 통하여 코팅층의 단사정 상은 열처리시간이 길어질수록 약간 증가하였다. 또한 비변태성 t'의 c/a는 용사상태에서 1.0099이였으며, 100시간 열처리 후에는 1.0115로 약간 증가하였다. 그리고 용사층의 접합강도는 열처리 시간이 길어질수록 감소하였다. 등온열처리 후에는 1.0115로 약간 증가하였다. 그리고 용사층 의 접합강도는 열처리 시간이 길어질수록 감소하였다. 등온열처리 후, 파괴는 주로 세라믹층에서 일어났으며, 반복 열처리되 시편에서는 10회 이후 대부분 금속결합층/세라믹층의 계면에서 일어났다.

• 디지털산업정보학회논문지
• /
• 제12권3호
• /
• pp.25-31
• /
• 2016

Mechanical properties of Y2O3-containing tetragonal ZrO2 polycrystals(Y-TZP) were investigated. Several additives were used to modify the hardness and fracture toughness of Y-TZP. The effects of these individual additives were discussed and their interactions were also analysed. Each additive, such as CoO, Fe2O3, MnO2 was found to deteriorate the mechanical properties of Y-TZP when it was used singly. But the fracture toughness of Y-TZP was significantly improved when these additives and Al2O3 were added in combination at a certain ratio. The addition of CoO, Fe2O3 and MnO2 into Y-TZP resulted in the more complex behavior of fracture toughness and hardness. The specimen with 1.5 wt%-Fe2O3, 3.0 wt% -Al2O3 and 1.5 wt%-CoO showed the monoclinic to tetragonal phase ratio of 18% and the highest toughness of $10.8MPa{\cdot}m1/2$ with Vickers hardness of 1201 kgf/mm2. However, the toughness decreased as the ratio increased and macrocracks developed beyond the ratio of 25%. Sample No. 16 is improved high Physical and Mechanical Properties.

• 한국세라믹학회지
• /
• 제54권5호
• /
• pp.413-421
• /
• 2017

In this work, we studied a fluorite structure oxides: Yttria stabilized zirconia, (YSZ); Gd doped $CeO_2$ (GDC); erbia stabilized $Bi_2O_3$ (ESB); Zr doped erbia stabilized $Bi_2O_3$ (ZESB); Ca doped erbia stabilized $Bi_2O_3$ (CESB) in the temperature range of 250 to $600^{\circ}C$ using electrochemical impedance spectroscopy (EIS). As is well known, grain boundary blocking effect was observed in YSZ and GDC. However, there is no grain boundary effect on ESB, ZESB, and CESB. The Nyquist plots of these materials exhibit a single arc at low temperature. This means that there is no space charge effect on ${\delta}-Bi_2O_3$. In addition, impedance data were analyzed by using the brick layer model. We indirectly demonstrate that grain boundary ionic conductivity is similar to or even higher than bulk ionic conductivity on cubic bismuth oxide.

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.269-276
• /
• 1996

The effect of sintering aids on the sinterability for silcion nitride has been studied by hundreds workers. However the effect of sintering aids on the machinability as the own trobles which is the major barrier for the field applications of the ceramic components has not been fully studied. in this study the contents of Al2O3 and Y2O3 in silicon nitride were varied from 0 to 8 wt% respectively. The physical and mechanical properties of the silcion nitride were measured. The optimal microstructure of silicon nitride balls with the excellent machinability by adding with various contents of sintering aids was studied by MGF(magnetic-fluid grinding)technique. An attempt to figure out how the mechanical properties influence the machinability of silicon-nitride ball was made.

• 한국세라믹학회지
• /
• 제36권2호
• /
• pp.145-150
• /
• 1999

고체산화물 연료전지의 양극재료로서 Gd1-xSrxMnO3을 구연산법으로 합성하였으며, 이의 결정구조, 전기전도도 및 열팽창률을 조사하였다. 또한 합성한 Gd1-xSrxMnO3을 8mol% yttria stabilized zirconia(8YSZ) 혹은 Ce0.8Gd0.2O1.9(CGO) 전해질과의 반응성을 조사하였다. Gd1-xSrxMnO3의 결정구조는 Sr함량이 증가함에 따라 orthorhombic (0$\leq$X$\leq$0.3)에서 cubic(0.4$\leq$X$\leq$0.5)을 거쳐 tetragonal (X=0.6)로 변하였다. Sr 함량이 증가함에 따라 Gd1-xSrxMnO3의 전기전도도는 증가하였다. 열팽창률은 Sr 함량이 30mol% 이상인 경우 함량이 증가함에 따라 증가하는 경향을 보이는 8YSZ, CGO와 비슷한 거동을 보였다. 8YSZ 및 CGO와의 반응성을 보기 위하여 Gd1-xSrxMnO3과 이들을 각각 혼합하여 130$0^{\circ}C$에서 48시간 동안 열처리했을 경우 8YSZ와는 SrZrO3의 반응물을 형성하였으나 CGO와는 반응을 하지 않았다.

• 한국재료학회지
• /
• 제8권9호
• /
• pp.783-790
• /
• 1998

용융점 및 물리.화학적 특성이 $\textrm{UO}_{2}$와 비슷한 yttria-stabilized-zirconia ($\textrm{ZrO}_{2}$-$\textrm{Y}_{2}\textrm{O}_{3}$)분말을 유도플라즈마(induction plasma)로 용융 침적시켜 원자력발전용 핵연료펠렛 제조공정에 응용하고자 하였다. 분말의 용융정도는 플라즈마동력 및 분말의 크기에 영향을 받는 것으로 나타났으며, 쉬스가스 조성, 분말분사관 위치, 입자크기 및 분사거리 등을 최적화 하여 Ar/$\textrm{H}_{2}$유량120/20$\ell$/min, 플리즈마 동력 80KW, 분사관의위치 8cm , 챔버압력 200Torr, 분사거리 18cm에서 이론밀도의 97.91%, 침적속도 20mm/min의 최적조건을 도출하였다. 침적시험에서 도출된 최적조건으로 펠렛몰더에서 제조한 펠렛은 96.5%의 밀도를 나타내었으며, 균일도 및 외곤도 우수하여 신기술에 의한 핵연료의 제조가능성을 확인하였다. 고밀도 침적에 영향을 미치는 각 변수들의 영향과 이들 변수들의 상호영향은 ANOVA(Analysis of Variance)을 이용하여 분석하였다.

• 한국세라믹학회지
• /
• 제43권2호
• /
• pp.69-73
• /
• 2006

A full retention of the tetragonal phase with coarse grains $(50\~60\;{\mu}m)$ was possible with the specimen $ZrO_2-1.9\;mol\%\;Y_2O_3$. In these coarse grains, $\{101\}_t$ annealing twins were frequently observed, although they do not exist in the usual fine grained specimens. The morphology and growth rate of the isothermally formed individual products are studied at an optical microscopic level. The habit planes of both products are also identified by performing two-surface trace analysis on the grains whose orientations are determined by the Electron Back Scattering Pattern (EBSP) method. The morphologies of isothermal martensite were well-defined thin plates and lenticular types. The growth rate in their longitudinal directions was quite slow and temperature-dependent. A two-surface trace analysis, incorporated with the EBSP method, identified the habit planes near $\{013\}_c$, in agreement with previous reports obtained from TEM works.

• 한국재료학회지
• /
• 제9권7호
• /
• pp.724-734
• /
• 1999

본 연구는 플라즈마 용사법에 의해 일반구조용 강재 (SS41, 30$\times$40$\times$60mm$^{t}$ )와 연마제로 블래스팅을 실시한 강재 (SS41P) 및 SS41P에 세라믹 분말을 코팅한 강재 (SS41PC)에 대한 SEM, 표면경도. 표면거칠기. 접촉각을 측정하였으며 이들의 표면형태에 대한 기계적 .물리적 특성을 고찰하였다 사용한 세라믹 용사분말은 \circled1 $Al_2$O$_3$ : alumina \circled2 $Al_2$O$_3$ 95%, TiO$_2$ 5% : alumina titania \circled3 ZrO$_2$: 95%, $Y_2$O$_3$5% : zirconia yttria이었다. 또한 SS41, SS41P. SS41PC에 대해 범용 고분자인 PE, PVC, PP PET, PS를 접착시킨 후 이들의 표면접착특성을 조사하였다. 그 결과 인장전단강도와 박리강도의 특성에서 SS41보다는 SS41P와 SS41PC의 표면상태가 고분자들을 접착시켰을 때 더 우수한 접착강도특성을 나타내었다. 범용 고분자들의 접착강도는 PE > PET > PP > PS > PVC 순이었다. 그리고 세라믹 표면과 고분자의 접착특성은 세라믹 표면의 표면거칠기 정도와 고분자의 세라믹 표면에 대한 anchor 효과의 크기 순으로 증가하였으며, SS41PC와 PE의 접착강도는 분자표면의 규칙성에 기인된 Synergy효과에 의해서 PVC보다 우수하게 나타난 것으로 판정된다

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.598-604
• /
• 2014

Considerable research efforts have been explored attempting to enhance the thermal durability of thermal barrier coatings (TBCs) at the high operating temperatures of gas turbines. In this study, the suspension plasma spray (SPS) process was applied to produce TBCs with a segmented structure by using an yttria-stabilized zirconia (YSZ) suspension. Four different experiment sets were carried out by controlling the ratio between surface roughness of the bond coat and feed stock size ($R_a/D_{50}$) in order to examine the effect of $R_a/D_{50}$ ratio on the microstructure of SPS-prepared coatings. When the $R_a/D_{50}$ had a high value of 11.8, a deposited thick coating turned out to have a cone-type columnar microstructure. In contrast, at the low $R_a/D_{50}$ values of 2.9 and 0.18, a deposited thick coating appeared to have a dense, vertically-cracked microstructure. However, with the very low $R_a/D_{50}$ value of 0.05 the coating was delaminated.

• 한국재료학회지
• /
• 제19권8호
• /
• pp.412-416
• /
• 2009

In this study, 3 mol% yttria-tetragonal zirconia polycrystal (3Y-TZP) nanoparticles were synthesized by the glycothermal method under various reaction temperatures and times. The co-precipitated precursor of 3Y-TZP was prepared by adding $NH_4OH$ to starting solutions, and then the mixtures were placed in an autoclave reactor. Tetragonal yttria-doped zirconia nanoparticles were afforded through a glycothermal reaction at a temperature as low as $220^{\circ}C$, using co-precipitated gels of $ZrCl_4$ and $YCl_3{\cdot}6H_2O$ as precursors and 1,4-butanediol as the solvent. The synthesized 3Y-TZP particles were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and Raman spectroscopy. The 3Y-TZP particles have a stable tetragonal phase only at glycothermal temperatures above $200^{\circ}C$. To investigate phase transition, the 3Y-TZP particles were heat treated from 400 to $1400^{\circ}C$ for 2 h. Raman analysis indicated that, after heat treatment, the tetragonal phase of the 3Y-TZP particles remained stable. The results of this study, therefore, suggest that 3Y-TZP powders can be prepared by the glycothermal method.