• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.878-883
• /
• 2001

The effects of external excitation with various frequencies and amplitudes on the flame behavior and pollution emission characteristics from a laminar jet flame are experimentally investigated. Measurements of $NO_{x}$ emission indices($EINO_{x}$), performed in unconformed and vertical lifted flame at resonance frequency by strong excitation, have been conducted experimentally. It was also conducted to investigate the effects of excited frequency on $NO_{x}$ emissions with a various frequency ranged 0Hz to 2kHz. From the vertical lifted flame like turbulent of the excited jet with resonance frequency was shown that the dependence of $NO_{x}$ emission could be categorized into three groups: Group 1 of intermediate flame length and relative narrow flame volume yielding low $NO_{x}$ emission, Group 2 of short flame length but large flame volume yielding high $NO_{x}$ emission and Group 3 of long flame length with low temperature contours yielding high $NO_{x}$ emission.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.126-128
• /
• 2004

Welding or joining of dissimilar material is difficult and have limitations because physical properties of each material like melting temperature, heat expansion coefficient, conductivity, yielding point, etc. are different. (omitted)

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(3)
• /
• pp.305-310
• /
• 1996

This paper concerns the cladding residual stresses in a reactor vessel induced during cooling from the manufacturing temperature down to room temperature Finite element results show that very large stress gradients are present at the interface corner and such stress singularity might lead to local yielding or cladding-base metal debonding.

• Structural Engineering and Mechanics
• /
• 제5권6호
• /
• pp.705-713
• /
• 1997

The residual thermal stresses at the interface corner between the elastic fiber and the viscoelastic matrix of a two-dimensional unidirectional laminate due to cooling from cure temperature down to room temperature were studied. The matrix material was assumed to be thermorheologically simple. The time-domain boundary element method was employed to investigate the nature of stresses on the interface. Numerical results show that very large stress gradients are present at the interface corner and this stress singularity might lead to local yielding or fiber-matrix debonding.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.361-361
• /
• 2006

To clarify the structure development of cyclic olefin copolymers in stretching and relaxation processes, on-line measurements of optical retardation and tensile force were performed. Birefringence increased continuously whereas stress showed yielding at stretching temperatures of $160^{\circ}C$. At $170^{\circ}C$, stress yielding was not observed and stress and birefringence increased monotonously with an increase in the strain. In the relaxation process, stress and birefringence decreased monotonously at all the temperatures examined. The slope for the stress vs. birefringence relation at initial stage of stretching increased with an increase in temperature, whereas that for the relaxation stage was significantly larger that for the stretching process, and therefore showed a significant hysteresis.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.172-176
• /
• 1995

This study deals with thermomechanical cracking between the friction surface and the interior of the brake disc. Analytical model considered in this study was a semi-infinite solid subjected to the thermal loading of an asperity moving with a high speed. The temperature field and the thermal stress state were obtained and discussed on the basis of Von Mises and Tresca Yielding Criterion. Analytical results showed that the dominant stress in cracking of friction brake is thermal stress and cracking location is dependent on the friction coefficient of contact and Peclet number. On the basis of analytical results thermomechanical cracking model is proposed.

• 한국작물학회지
• /
• 제25권2호
• /
• pp.58-63
• /
• 1980

Early Russian, 수원 005 및 흑색재래종의 3참깨 품종을 공시재료로 하여 최대개화기에 개화결실한 삭을 대상으로 품종간의 등숙과 수량특성을 경시적으로 추적조사한 결과 다음의 결론을 얻었다. 1. Early Russian은 대형삭을 착생하며 개화후 30일정도에 성숙하고 지방함량이 높아서 우리 나라의 기상조건에 적합한 등숙특성을 갖는 품종이라 하겠다. 그러나 충분한 등숙기간과 등숙조건하에서는 삭과 종실의 건물 및 용적증대 경향 및 삭당종실수의 증가 경향으로 보아서 상대적으로 삭의 발달에 취약성을 갖는 것으로 판단된다. 2. 수원 005는 다수성 품종으로서 유리한 점은 갖으나 충분한 등숙조건과 등숙기간이 있어야 한다. 그것은 삭에 비하여 종실의 건물형성이 늦고 개화후20일경까지 종실수가 확보되므로 등숙후기에 형성되는 종실의 등숙 발육에 충분한 등숙조건과 등열기간이 요구되므로 우리나라의 남부에서 생산체재력이 잘 발현될 가능성이 있다. 3. 흑색의 육각재래종은 비교적 수양성이 낮으며 종실의 용적과 건물생성은 성숙기까지도 서서히 증가하는데 반하여 삭의 형성은 개화후 20 일경까지도 제한되고 있어서 등숙기간이 연장되어도 수량성의 증대효과는 크지 않을 것으로 판단된다.

• 수산해양기술연구
• /
• 제28권3호
• /
• pp.295-305
• /
• 1992

The critical strain energy release rate and the failure mechanisms of glass-carbon epoxy resin hybrid composites are investigated in the temperature range of the ambient temperature to 8$0^{\circ}C$. The direction of laminates and the volume fraction are [(+45, -45, 0, 0) sub(2) ] sub(s), 50%, respectively. The major failure mechanisms of these composites are studied using the scanning electron microscope for the fracture surface. Results are summarized as follows: 1) The critical strain energy release rate shows a maximum at ambient temperature and it tends to decrease as temperature goes up. 2) The critical strain energy release rate increases as the content of glass increases, and especially shows dramatic increase for the high glass fiber content specimens. 3) Major failure mechanisms can be classfied such as localized shear yielding, fiber-matrix debonding, matrix micro-cracking, and fiber pull-out and/or delamination.

• 한국재료학회지
• /
• 제27권3호
• /
• pp.127-131
• /
• 2017

Isosteric heat of hydrogen adsorption is one of the most important parameters required to describe solid-state hydrogen storage systems. Typically, it is calculated from adsorption isotherms measured at 77K (liquid N2) and 87K (liquid Ar). This simple calculation, however, results in a high degree of uncertainty due to the small temperature range. Therefore, the original Sievert type setup is upgraded using a heating and cooling device to regulate the wide sample temperature. This upgraded setup allows a wide temperature range for isotherms (77K ~ 117K) providing a minimized uncertainty (error) of measurement for adsorption enthalpy calculation and yielding reliable results. To this end, we measure the isosteric heats of hydrogen adsorption of two prototypical samples: activated carbon and metal-organic frameworks (e.g. MIL-53), and compared the small temperature range (77~87K) to the wide one (77K ~ 117K).

• Steel and Composite Structures
• /
• 제36권4호
• /
• pp.383-398
• /
• 2020

This paper investigates the progressive collapse behavior of 3D steel-framed gravity buildings under fires with a cooling phase. The effect of fire protections and bracing systems on whether, how, and when a gravity building collapses is studied. It is found that whether a building collapses or not depends on the duration of the heating phase, and it may withstand a "short-hot" fire, but collapses under a mild fire or a "long-cool" fire. The collapse time can be conservatively determined by the time when the temperature of steel columns reaches a critical temperature of 550 ℃. It is also found that the application of a higher level of fire protection may prevent the collapse of a building, but may also lead to its collapse in the cooling phase due to the delayed temperature increment in the heated members. The tensile membrane action in a heated slab can be resisted by a tensile ring around its perimeter or by tensile yielding lines extended to the edge of the frame. It is recommended for practical design that hat bracing systems should be arranged on the whole top floor, and a combination of perimeter and internal vertical bracing systems be used to mitigate the fire-induced collapse of gravity buildings. It is also suggested that beam-to-column connections should be designed to resist high tensile forces (up to yielding force) during the cooling phase of a fire.