• Design & Manufacturing
• /
• v.9 no.2
• /
• pp.20-24
• /
• 2015

Recently, the light guide plate (LGP), a component of the BLU, becomes thinner and larger than ever. In industrial field, specialized injection molding technique is applied to mold the ultra-thin LGP such as a ultra-high speed injection molding. Usually very high melt temperature is used for low viscosity. High injection speed and melt temperature lead to yellowing of LGP. In the present paper a series of injection molding experiment was performed under various injection molding conditions. Yellow index, CIE xy, spectral transmittance of sample were measured using the UV-Visible spectrophotometer. Systematic decrease of spectral transmittance in UV-B range was found as the melt temperature was higher. Yellow index and CIE xy were became higher near the gate location in LGP. From the result of analysis of variance, the main factor to affect for yellow index was mold temperature and that for spectral transmittance(at 315 nm) was melt temperature.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1248-1251
• /
• 2005

In PDP, a transparent dielectric is formed on a front glass substrate so as to cover bus electrodes (Ag). During the fabrication process, sometimes, a transparent dielectric reacts with bus (Ag) electrode in the range of $560-600^{\circ}C$, and the reaction gives the dielectric its yellow coloration, what is called "yellowing phenomena". In this paper, we investigated the reaction between bus electrode and transparent dielectric covered with different frit content in Ag paste.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.30-41
• /
• 2017

Types of noise barrier installed for noise attenuation are largely divided into noise-absorbing format and noise-proofing format. In these days, installation of transparent noise barrier is general trend to solve problems that hinder sunshine and landscape. Some kinds of transparent boards are used to one of components in noise barriers, but in some cases, less transparency and worse pollution due to yellowing phenomena, and severe material deformation are to harm the urban aesthetics Therefore laminated-tempered glass board in that yellowing phenomena does not occur can be replaced as a transparent one to secure those shortcomings. In this paper, the structural safety against train induced vibration and the resistibility to wind load are analyzed for laminated-tempered glass system as a component of noise barrier installed on Metro railway elevated bridges. Also the appropriateness is evaluated through flexural bending performance test, compressive strength test, modulus of elasticity tests, and impact test for the system or the glass material itself. All of these processes are intended to present the deployment of logic to evaluate the adequacy for the system.

• Conservation Science in Museum
• /
• v.21
• /
• pp.1-16
• /
• 2019

This study investigated the material properties of UV-curable Resin in order to identify stable materials for use in the restoration of glass cultural properties. Tested samples were based on acrylic UV-curable Resin (SECURE CP-7321®), to which urethane UV-curable Resin (FLGPCL04 Clear®) was added in 10% increments to produce eleven samples. The results showed that all eleven samples had similar properties in terms of refractive index, density, adhesive strength, and anti-yellowing. But the surface hardness and compressive strength were optimal and effective for maintaining the shape of artifacts after restoration treatment when the proportion of urethane resin was in the range of 10-20%. Based on these findings, the mixing sample [acrylic UV-curable Resin(9) : urethane UV-curable Resin(1)] was applied in the conservation treatment of a glass cultural propertie (Hwangbuk 519) excavated from the North Mound of Hwangnamdaechong, Tomb in Gyeongju.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.28 no.6
• /
• pp.1304-1309
• /
• 1999

The respiratory characteristics and quality attributes of mature green mume fruits as influenced by modified atmosphere packaging(MAP) conditions during storage at 25oC for 8 days were investigated. The quality attributes of mume fruits were evaluated in terms of fresh weight loss, physiological injury and yellowing. The packaging materials used for MAP were low density polyethylene(LDPE) films with various different thicknesses. Yellowing and fresh weight loss of mume fruits were noticeably reduced by the packaging treatments with LDPE A and B. The physiological injury of the fruits during storage was found to be more severe in LDPE C than others. For LDPE A and B, the oxygen and carbon dioxide contents within the packages of Mume fruits maintained at the levels of 2~3% and 7~8%, respectively. With respect to visual quality, MAP prolonged the shelf life of the fruits much longer compared with the unsealed control. From the experimental results, it is suggested that the LDPE films with the gas trans mission rates of about 2,100 O2 ml/m2.day.atm and 6,700 CO2 ml/m2.day.atm would be proper for MAP of mature green mume fruits during storage at ambient temperature.

• The Plant Pathology Journal
• /
• v.34 no.5
• /
• pp.426-434
• /
• 2018

During the spring season of 2014, a total of 148 melon and watermelon leaf samples were collected from symptomatic and asymptomatic plants in the western and southwestern regions of Saudi Arabia and were tested for the presence of Watermelon chlorotic stunt virus (WmCSV) and other suspected cucurbit viruses by double antibody sandwich enzyme-linked immunosorbent assays. Ninety-eight samples were found to be positive for the presence of WmCSV, nine samples were positive for the presence of Cucurbit yellow stunting disorder virus (CYSDV), and 22 showed a mixed infection with both WmCSV and CYSDV. No other cucurbit viruses were detected in any of the samples. Host range experiments revealed that eight out of fourteen tested plant species were susceptible to WmCSV. PCR products of approximately 1.2 kb were obtained after amplification using primers specifically targeting the coat protein region of WmCSV. Positive PCR results were confirmed by dot blot hybridization. Coat protein gene sequences from eleven WmCSV isolates indicated that the highest identity was between the 104WMA-SA isolate from the Wadi Baish location and a previously reported isolate from the AL-Lith location in Saudi Arabia. The lowest identity was observed between the 42WMA-SA isolate and an isolate from Palestine.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.32 no.2
• /
• pp.130-136
• /
• 1987

The studies were carried out to investigate the occurrence of excessive dried leaves during burley tobacco curing. Six different periods of ventilation during the entire stage of curing were applied. And also 3 different heights of rolling up polyethlene film for side ventilation of the curing house combined with 4 different spaces between garlands were applied from after yellowing. The high air temperature and low relative humidity from end of yellowing to end of browning stage were the most critical to occur excessive dried \eaves. As side ventilation was continued for the entire stage of curing, air temperature in curing house was lower and occurrence of excessive dried leaves were remarkably decreased. The air temperature was not affected on hanging spaces, but relative humidity that resulted significantly in decreasing of the excessive dried leaves was increased by narrowing of hanging spaces. As excessive dried leaves were increased, its price per kg was lower, its physical properties was worse and its total nitrogen and total suger were higher than those of normal cured leaves.

• Journal of Bio-Environment Control
• /
• v.27 no.2
• /
• pp.180-184
• /
• 2018

This study was conducted to examine the effect OTR film type on the quality of garden cress (Lepidium sativum L.) baby leaf during MA storage. Garden cress harvested at baby leaf size of 10cm plant height packed with 1,300 cc, 10,000 cc, 20,000 cc, 40,000 cc, and $80,000cc{\cdot}m^{-2}{\cdot}day^{-1}{\cdot}atm^{-1}$ OTR (oxygen transmission rate) films and MP (micro-perforated) film, and then stored at $8^{\circ}C$ for 10 days. All of the OTR film treatments showed a decrease of 0.5% fresh weight until the storage end date and a 1.3% decrease in the MP film treatment. The oxygen concentration in the packaging during storage was maintained at 18% or more in 20,000 cc, 40,000 cc, and 80,000 cc OTR film treatments, while the 1,300 cc OTR film treatment decreased to 11% at the storage end date. And the concentration of carbon dioxide was steadily increased in the 1,300 cc and 10,000 cc OTR film treatments to show the levels of 4.5% and 3.4%, respectively, and the other OTR film treatments showed a concentration of less than 1%. Ethylene concentration in the package was maintained at the highest level of $3-5{\mu}L{\cdot}L^{-1}$ in the 1,300 cc treatment during the storage period. The lowest odor and the highest quality of appearance were observed in the 1,300 cc treatment, but the MP film treatment and the other OTR treatments lost marketable quality due to yellowing. The color of garden cress baby leaf was changed the lowest in 1,300 cc treatment that showed the highest chlorophyll content and Hue angle value, lowest $b^*$ value, present of yellowing at end of storage date. Therefore, 1,300 cc treatment which was most effective for yellowing and odor suppression during storage is considered to be suitable for packaging of garden cress baby leaf.

• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.37-46
• /
• 2015

In the case of adhesives & restoration agents currently being used for the preservation treatment of ceramics and earthenware, epoxy type, cellulose type and cellulose type are mainly being used. However, they are showing various problems such as re-detachment from severe contraction, color change from yellowing, work inconvenience of staining on tools and hand during usage and irreversibility. For the purpose of solving the issues of yellowing and irreversibility of epoxy resin being used to restore ceramics, urethane synthetic resin with low yellowing excellent reversibility has been developed in this study. The adhesive strength of urethane resin that has been developed has excellent properties with 2.07MPa for undiluted solution, which is 1.5 times higher than that of existing material EPO-$TEK301^{(R)}$ 1.21MPa. The result of workability measurement showed that the wear rate of urethane resin (in Talc 50wt%) was 1.09%, which was somewhat higher than that of existing material Quick $Wood^{(R)}$ (1.02%). In addition, its wear rate is two times higher than that of $EPO-TEK301^{(R)}$ (0.41%) and $L30^{(R)}$ (0.39%), thereby showing an advantage in its forming process compared to existing materials. As for the advantage of urethane resin of reversibility experiment, 12 hours after acetone, ethyl alcohol deposition, urethane resin and filler talc were dissolved 100% while showing powdering phenomenon. Compared to 0% reversibility of existing epoxy resin, it has much superior reversibility. The result of UV rays experiment to evaluate its durability showed that ${\Delta}E^*ab$ color change value based on undiluted solution of urethane resin was 2.76 before & after UV rays exposure, which was a decrease by about 7-20 times compared to that of existing resin, thereby minimizing the issue of heterogeneity.

• Korean Journal of Ecology and Environment
• /
• v.51 no.4
• /
• pp.259-267
• /
• 2018

This study was conducted to confirm phenological response of main deciduous woody species in Korea according to elevated temperature. Based on seeds collected from the same place, 39 woody species were cultivated in field (control) and in greenhouse (treatment) that was maintained above base temperature ($4.8^{\circ}C$). And then, we observed phenotype change of leaves focused on phenological response and explained relation with their current distribution area. As a result, initiation period of leaves unfolding was 1st~3rd, May in control. It was 13, December~7, January in treatment. Period of leaves yellowing was 11~26, October in control. It was 30, October~13, November in treatment. Consequently, initiation period of leaves unfolding was faster by 119~140 days and period of leaves yellowing was slower by 3~32 days since elevated temperature. Period of leaves growth increased in treatment by 148 days than control. Quercus mongolica and Quercus serrata that cultivated in treatment was changed as evergreen trees which have grown up continuely during one year. Also, initiation period of leaves unfolding of Sorbus alnifolia in treatment was faster than in control. However, difference of the period between control and treatment was smallest. Because period of yellowing leaves was moved ahead. Phenological response of leaves according to elevated temperature had no relation of type of their current distribution area. This is the result of acclimation due to elevated temperature during the winter and suggests that the phenotype of leaves of 39 deciduous woody species is more sensitive to the current growth condition than to the past growth condition.