• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.71-74
• /
• 1999

접지면을 가지는 정사형 조셉슨 결합을 제작하기 위한 기본 단계로 YBCO/STO/YBCO 구조의 다층 박막을 제작하였다. 상하부 YBCO 박막은 그 사이에 존재하는 STO 절연층에 형성된 홀을 통해 서로 연결되어 있으며 이것의 저항-온도 특성을 측정한 결과 임계 온도가86 K로 나타났다. 이 결과는 시편을 매우 장시간동안 열처리한 후 얻은 결과로서 YBCO/STO/YBCO 다층 구조의 박막 제작시 하부 YBCO 박막의 특성이 많이 저하되고 이를 복원하기 위해서는 열처리 공정이 매우 중요함을 알 수 있었다. 현재 우수한 특성을 가지는 YBCO/STO/YBCO 다층 구조의 제작 공정을 최적화하기 위한 연구를 계속 수행 중에 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.249-251
• /
• 1996

Ag coating on the textured YBCO and PTFE coating on the sintering YBCO were prepared. The critical current densities of different YBCO samples with and without coatings were compared. Both of Ag coating and PTFE coating can well protect YBCO from moisture and $CO_2$.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1996년도 재료학회 추계학술발표회
• /
• pp.171-173
• /
• 1996

Ag coating on the textured YBCO was prepared by means of a Ag$_2$O brushed coating method. The contact between Ag coating and textured YBCO was examined by sharp knife cut and by the observation of SEM. The critical current densities of different textured YBCO samples, which included YBCO with and without Ag coating, and YBCO with Ag coating after hot moist text, were compared. The Ag coating does not influence the oxygen absorption of textured YBCO, but Ag coating can protect YBCO well from moisture and $CO_2$

• Progress in Superconductivity
• /
• 제11권1호
• /
• pp.62-66
• /
• 2009

Introduction of proper impurity into $YBa_2Cu_3O_{7-x}$ (YBCO) thin films is an effective way to enhance its flux-pinning properties. We investigate effect of $Y_2O_3$ nanoparticles on the critical current density $J_c$ of the YBCO thin films. The $Y_2O_3$ nanoparticles were created perpendicular to the film surface (parallel with the c-axis) either between YBCO and substrate or on top of YBCO, YBCO/$Y_2O_3$/LAO or $Y_2O_3$/YBCO/STO, by pulsed laser deposition. The deposition temperature of the YBCO films were varied ($780^{\circ}C$ and $800^{\circ}C$) to modify surface morphology of the YBCO films. Surface morphology characterization revealed that the lower deposition temperature of $780^{\circ}C$ created nano-sized holes on the YBCO film surface which may behave as intrinsic pinning centers, while the higher deposition temperature produced much denser and smoother surface. $J_c$ values of the YBCO films with $Y_2O_3$ particles were either remained nearly the same or decreased for the samples in which YBCO is grown at $780^{\circ}C$. On the other hand, $J_c$ values were enhanced for the samples in which YBCO is grown at higher temperature of $800^{\circ}C$. The difference in the effect of $Y_2O_3$ can be explained by the fact that the higher deposition temperature of $800^{\circ}C$ reduces intrinsic pinning centers and $J_c$ is enhanced by introduction of artificial pinning centers in the form of $Y_2O_3$ nanoparticles.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.374-374
• /
• 2009

We have fabricated pure YBCO films and $BaZrO_3$ doped ones on $CeO_2$ buffered YSZ single crystal substrates using rf-sputtering method. In this work, pure YBCO and 2 vol% BZO doped YBCO target were used to investigate the flux pinning properties of BZO doped YBCO films compared to undoped ones. BZO nanodots within the superconducting materials was known to comprise the self-assembled columnar defects along the c-axis from the bottom of YBCO films up to the top surface, thus can be a very strong pinning sites in the applied magnetic field parallel to them. We will discuss the possibility of growing self-assembled columnar defects in the rf-sputtering method. It is speculated that BZO and YBCO phases can separate and BZO form nanodots surrounded by YBCO epitaxial layers and continuous phase separation and ordering between these two materials, which was well studied in Pulsed Laser Deposition method. For this purpose, some severe experimental conditions such as on-axis sputtering, shorter target-substrate distance, high rf-power, etc was adopted and their results will be presented.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.234-238
• /
• 1995

In this parer, by means of adding nonsuperconductive phase sliver into YBCO matrix, the superconductivity of Melted Texture Growth (MTG) YBa$_2$Cu$_3$O$\_$7-x/ was improved remarkably. In order to eliminate the crack inthe YBCO and the weak linkin the grain boundary, Ag contents from 2wt% to 18Wt% were doped in the YBCO It was found that J$\_$c/ of YBCO increase with the increasing Ag content till 14 wt% over 14wt% of Ag content, the Jc tends to stable . The grain size of YBCO became fine when Ag was added in the YBCO and X-ray diffraction showed that the YBCO crystal prepared by the above technique had (001) orientation and growing plane of YBCO was a-b plane. Using Bens medel, the J$\_$c/ was calculated and the best result was J$\_$c/ 76000A$\textrm{cm}^2$(77K, 100Gs).

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.34-37
• /
• 1999

We have fabricated YBCO/STO/YBCO multilayer by the pulsed laser deposition method varing the deposition condition of insulating STO layer. Superconducting properties of both YBCO layers are sensitively affected by the deposition condition of STO layer. We obtained the upper YBCO layer of T$_{c(zero)}\;{\sim}\;$90 K with a good reproducibility, however, T$_{c(zero)}$ of lower YBCO layer was decreased to about 80 K maybe due to the oxygen loss during the deposition of STO layer. Superconducting properties of both YBCO layers at every fabrication step were measured in order to study the reason for the deterioration of superconducting properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.247-248
• /
• 2006

Bulk YBCO 초전도체는 top-seeded melt-growth 방법으로 제조되었다. YBCO bulk는 Epoxy resin과 $AgNO_3$를 보강해 초전도체의 기계적 강도를 향상하고자 하였다. Epoxy resin은 보강 재료인 STYCAST 2850-FT와 경화제인 CATALYST 24LV 를 100:5 비율로 혼합하여 제조한 후 mould에 넣고 $66^{\circ}C$에서 2시간 열처리 하였다 (rotary pump로 진공 분위기 조성). $AgNO_3$는 $350^{\circ}C$에서 2시간, $450^{\circ}C$에서 1시간 열처리 하여 Ag와 $NO_3$의 분리 후 YBCO bulk에 Ag가 보강되도록 하였다. Epoxy resin 과 분리된 Ag는 YBCO bluk의 crack과 void에 침투되는 것을 SEM과 광학현미경을 통해 관찰할 수 있었다. Three point bending test를 이용하여 보강 전후의 YBCO bulk의 기계적 강도를 측정하였다. 보강 후의 YBCO bluk의 기계적 강도는 보강 전에 비해 향상된 결과를 확인할 수 있었고, Epoxy resin과 $AgNO_3$를 보강한 YBCO는 기계적 강도 향상에 높은 신뢰성을 보이고 있다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.77-80
• /
• 1999

In this paper. We experimentally investigated the magnetic properties of YBCO bulk superconductor using AC magnetization method. The sample is 2.8cm wide in a diameter and 1.4cm long. We applied Ac magnetic field parallel to the direction of length of YBCO bulk. It is observed that YBCO bulk has the diamagnetic properties. AC loss calculation of YBCO bulk superconductor was performed by evaluating the total area of magnetization traces. As depends on the frequency and amplitude of the applied magnetic field.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 추계학술대회 논문집
• /
• pp.90-92
• /
• 2003

Effects of organic additives on YBCO coated conductor prepared by MOD-TFA method were investigated. YBCO thin films were deposited on (100)-oriented single crystalline LaAlO$_3$substrates by conventional MOD-TFA process. The microstructures of YBCO thin films show labyrinth-like patterns. The origin of this microstructure was delineated by compositional inhomogeneity during the pyrolysis process of MOD process and it was shown that organic additives changes the microstructure and texture development of grown YBCO films