• Journal of the Mineralogical Society of Korea
• /
• v.16 no.2
• /
• pp.151-159
• /
• 2003

$^{31}$ /P NMR and XRD have been used to study the mineralogical compositions and the phosphorus species in marine sediments near Wolsung nuclear power plant. The core samples with 30cm depth were investigated and no mineralogical changes have been found. The studied marine sediments were composed of quartz, albite, microcline, calcite, and some clay minerals such as illite, smectite, chlorite, and kaolinite. Only orthophosphate-monoester and very small amount of ortho-phosphate-diester were identified as phosphorus species in the studied sample, different from the species reported in other countries. These phosphorus species are mainly from organisms and was exposed to the oxic conditions. The consistent mineralogical compositions as well as the same phosphorus species throughout the entire core samples indicate that the constant oxic condition was kept without any changes in sedimentary conditions or the sediments were deposited with different sedimentary conditions, but later they were disturbed by other activities and exposed to the surface oxic conditions continuously.

• Journal of the Korean Vacuum Society
• /
• v.13 no.2
• /
• pp.72-78
• /
• 2004

Cu seed layers deposited by magnetron sputtering onto tantalum nitride barrier films were treated with ECR plasma and then the copper films were electroplated and rapid thermal annealed in an argon or nitrogen atmosphere at various temperatures ranging from 200 to $500^{\circ}C$. Changes in the microstructure and physical properties of the copper films electroplated on the hydrogen ECR plasma cleaned copper seed layers were investigated using X-ray diffraction (XRD), electron back-scattered diffraction (EBSD), and atomic force microscopy (AFM) analyses. It was found that the copper film undergoes complete recrystallization during annealing at a temperature higher than $400^{\circ}C$. The resistivity of the Cu film tends to decrease and the degree of (111) preferred orientation tends to increase as the annealing temperature increases. Theoptimum annealing condition for obtaining the film with the lowest resistivity, the smoothest surface and the highest degree of the (111) preferred orientation is rapid thermal annealing in a nitrogen atmosphere at $400^{\circ}C$ for 120 s. The resistivity and the surface roughness of the electroplated copper film annealed under this condition are 1.98 $\mu$O-cm and 17.77 nm, respectively.

• Journal of Adhesion and Interface
• /
• v.10 no.1
• /
• pp.23-29
• /
• 2009

We investigated effects of a compatibilizer on the rheological properties during mixing and thermal properties of polypropylene (PP)-natural fiber composites. Two types of natural fibers (cotton fiber and wood fiber) were compared. maleic anhydride grafted PP was used for a compatibilizer. On increasing the amounts of the compatibilizer, the torque values of composites were increased, regardless of the kind of fibers. X-ray diffraction (XRD) and differential scanning calorimetry (DSC) results showed a slight increase in the degree of crystallinity with adding the compaibilizing agent, while the effects of the kind of fibers were marginal. It may be considered, however, the cotton fiber exhibits better interaction with PP-g-MAH than the natural fiber based on the rheographs, DSC, and XRD results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.22-23
• /
• 2005

In order to increase the critical current of coated conductor, highly Bi-axially textured substrates are required. Texture uniformity of substrate is also important to fabricate high quality superconducting coated conductor because the amount of current flow along the coated conductor is limited by the defects such as bad textured area. Therefore, we need to evaluate the distribution of texture of Ni substrate along the length before buffer layer deposition on Ni tape. R2R(reel-to-reel) XRD system was used to measure the texture of long Ni substrate continuously. $\theta-2\theta$ scan of 10 m long Ni tape was measured and indicates that some of Ni(111) planes equally remain on Ni(002) textured substrate. The results of continuous Ni(220) $\Phi$-scan indicate that average FWHM is 9$^{\circ}$ within $\pm$1.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1760-1767
• /
• 2010

FAT compounds photocatalysts were prepared with $TiOSO_4{\cdot}xH_2O$ (TOS) by a sol-gel method. The samples were characterized by scanning electron microscopy (SEM), BET specific surface area, X-ray diffraction analysis (XRD) and energy dispersive X-ray spectroscopy (EDX). The SEM results showed that ferric compounds and titanium dioxide were fixed onto the AC surfaces. The XRD results showed that Fe-AC/$TiO_2$ composites mostly contained anatase phase. EDX showed the presence of C, O, and Ti with Fe peaks in all samples. The photocatalytic activities were evaluated by the photocatalytic oxidation of methylene blue (MB) solution, via compare photodegradation of MB solution under visible light and UV light separately. Fe-AC/$TiO_2$ composites had an excellent photocatalytic under strong visible light irradiation. A small amount of Fe ions in AC/$TiO_2$ particles could obviously enhance their photocatalytic activity.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.5
• /
• pp.513-518
• /
• 2005

Catalytic oxidation of toluene on the manganese oxide catalysts and manganese-cerium oxide catalysts was investigated. The catalysts were characterised by X-ray diffraction(XRD), thermo gravimetric analyzer(TGA), toluene-temperature program reduction(Toluene-TPR). We found that the optimal manganese content was 18.2 wt.% and the optimal cerium content was 10.0 wt.% at catalytic oxidation of toluene. It is shown that ceria improves the activity of manganese oxide phases. From the XRD results, it was estimated that $MnO_2$ phase was active site in the monometallic and bimetallic catalysts. From the TGA and Toluene-TPR results, it show that ceria improves the mobility of the lattice oxygen, adequate oxidation state of the active phase, reduction ability at low temperature, and re-oxidation of the active site.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.409-419
• /
• 2002

Nowadays, antiwashout underwater concrete is widely used for constructing underwater concrete structures but they, especially placed in marine environment, can be easily attacked by chemical ions such as SO$\^$2-/$\_$4/ Cl$\^$-/ and Mg$\^$2＋/, so the quality and capability of concrete structures go down. In this paper, to solve and improve those matters, flyash and GGBFS(ground granulated blast furnace slag) were used as partial replacements for ordinary portland cement. As results of experiments for fundamental properties of antiwashout underwater concrete containing 10, 20, 30％ of flyash and 40, 50, 60 ％ of GGBFS respectively, setting time, air contents, suspended solids and pH value were satisfied with the "Standard Specification of Antiwashout Admixtures for Concrete" prescribed by KSCE, and also slump flow, efflux time and elevation of head were more improved than that of control concrete. From the compressive strength test, it was revealed that the antiwashout underwater concrete containing mineral admixtures(flyash and GGBFS) is more effective for long term compressive strength than control concrete. An attempt to know how durable when they are under chemical attack has also been done by immersing in chemical solutions that were x2 artificial seawater, 5 ％ sulphuric acid solution, 10％, sodium sulfate solution and 10％ calcium chloride solution. After immersion test for 91days, XRD analysis was carried out to investigate the reactants between cement hydrates and chemical ions and some crystalline such as gypsum ettringite and Fridel′s salt were confirmed.

• Polymer(Korea)
• /
• v.27 no.1
• /
• pp.52-60
• /
• 2003

In this work, two types of Ni-plating, namely electrolytical and electroless Ni-platings on carbon fiber surfaces, were carried out to enhance the impact resistance of composites. And the comparison between electrolytical and electroless methods on their impact properties of composite system was studied. The surface properties of carbon fibers were characterized using XRD, SEM, and contact angle measurements. The impact behaviors were investigated using an Izod type impact tester. As experimental results, it was observed that electrolessly plated Ni layers had Ni-P alloys on carbon fiber surfaces as revealed by XRD, and electrolytically Ni-plated carbon fibers showed higher surface free energies than those of the electrolessly Ni-plated carbon fibers. In particular, the impact strengths of electrolessly Ni-plated carbon fibers-reinforced plastics were strongly increased. These results were probably due to the difference of wettabilities according to the different types of Ni-plating methods.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.37-40
• /
• 2009

불소가 도핑된 산화주석(SnO2:F, FTO) 박막은 다결정 전도성 세라믹으로 가시광선 영역에서 투명하기 때문에 태양전지의 전극으로 활용된다. 본 연구에서 FTO는 APCVD법으로 성막되었다. BSG기판을 사용하여 $620^{\circ}C$의 고온에서 공정이 진행되었다. 이렇게 제작된 FTO 박막은 수소, 질소, 대기 분위기에서 여러 열처리 시간을 변수로 실험하여 열처리 전후의 전기적, 광학적, 구조적 변화를 관찰하고 분석하였다. 전기적 특성 분석에는 전기 비저항, 모빌리티 및 캐리어 농도 등의 변화를 알아보았고, 광학적 분석에는 UV-vis spectoscopy로 200nm에서 800nm 파장대역의 투과도를 구하고, Hazemeter를 통하여 총투과율, 평행투과율, 확산투과율 및 Haze를 분석하여 FTO막이 가지고 있는 texturing에 의한 효과를 알아보기 위하여 시편의 열처리 전후를 비교 분석하였다. 구조적 분석은 XRD를 이용하여 pattern을 분석하여 FTO가 가지는 구조변화를 분석하였다. 특히 FTO의 texturing에 기여도가 높은 (200)면의 XRD peak강도가 상승함에 따라 후열처리에 의해 박막의 표면의 변화가 일어남을 확인하였다. FTO의 후열처리에 의한 변화는 전기적으로는 약간의 전기 비저항의 증가를 가져오며, 캐리어 농도의 감소를 가져온다. 캐리어 농도의 감소에 따라 모빌리티의 상승이 관찰되었다. 광학적 특성은 가시광선 영역에서 투과율은 거의 같거나 약간 감소하는 경향을 나타내며, 후열처리 전후에 거의 동일한 투과율을 보이면서도 확산 투과율이 상승하는 분석 결과를 얻었다.

• Journal of the Korean earth science society
• /
• v.35 no.6
• /
• pp.401-411
• /
• 2014

In order to enhance the Au Ag leach rate, a mechanochemical activation process and a mixed thiourea-thiocyanate solution has been applied to Au concentrate. To achieve mechanochemical activation, the Au concentrate was mechanically ground using a dry and a wet process. The results of a particle size distribution analysis and an XRD analysis, average particle size and crystallite size were much smaller in the dry-sample than in the concentrate sample. As well the size was smaller in the wet-sample than in the dry-sample. In SEM and XRD analysis, the amorphization effect was observed in the wet-sample due to mechanochemical activation. Au Ag leaching experiments were carried out with a thiourea solution, a thiocyanate solution and a mixed thiourea-thiocyanate solution. The Au Ag leach rate was much greater in the dry-ground-sample than in the concentrate sample, and the leach rate was greater in the wet-ground-sample than in the dry-sample. The Au Ag leach rate was much greater in the thiocyanate solution than in the thiourea solution, and the leaching rate was much greater in the mixed thiourea-thiocyanate solution than in the thiocyanate solution. Up to a 99% leach rate for Au Ag were only achieved in the wet-sample using the mixed thiourea-thiocyanate leaching solution.