• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.557-565
• /
• 2014

We report the effect of basal-plane stacking faults (BSFs) on X-ray diffraction (XRD) of non-polar (11$\underline{2}$0) a-plane GaN films with different $SiN_x$ interlayers. Complete $SiN_x$ coverage and increased three-dimensional (3D) to two-dimensional (2D) transition stages substantially reduce BSF density. It was revealed that the Si-doping profile in the Si-doped GaN layer was unaffected by the introduction of a $SiN_x$ interlayer. The smallest in-plane anisotropy of the (11$\underline{2}$0) XRD ${\omega}$-scan widths was found in the sample with multiple $SiN_x$ layers, and this finding can be attributed to the relatively isotropic GaN mosaic resulting from the increase in the 3D-2D growth step. Williamson-Hall (WH) analysis of the (h0$\underline{h}$0) series of diffractions was employed to determine the c-axis lateral coherence length (LCL) and to estimate the mosaic tilt. The c-axis LCLs obtained from WH analyses of the present study's representative a-plane GaN samples were well correlated with the BSF-related results from both the off-axis XRD ${\omega}$-scan and transmission electron microscopy (TEM). Based on WH and TEM analyses, the trends in BSF densities were very similar, even though the BSF densities extracted from LCLs indicated that the values were reduced by a factor of about twenty.

• 한국광물학회지
• /
• 제32권4호
• /
• pp.287-301
• /
• 2019

문화재의 보존·관리 및 활용은 원형유지를 기본원칙으로 하므로 비파괴적인 분석법을 통한 무기질 문화재 및 그 원료물질의 광물조성을 연구하는 것은 중요한 분야이다. 본 연구는 비파괴 표면 X-선 회절분석법(ND-XRD)을 석재, 채색된 안료, 토제, 금속 등 유형별 무기질 문화재 및 시편들을 대상으로 적용하여 문화재의 비파괴 분석법 중 하나로써 활용가능성을 검토하였다. 그 결과, 기기 내에 거치가 가능하며, 구성입자의 크기나 배열 및 굴곡 등 분석대상면의 특성이 스캔에 적합한 시료일 경우 모든 유형에서 광물조성 해석에 활용 가능한 회절패턴이 획득되는 것으로 나타났다. 또한 시료의 기질부에 비하여 표면의 회절정보가 우세하게 획득되므로 수평적 또는 수직적으로 다른 물질로 구성된 대상에 적용할 경우 각 부위별 광물조성정보와 함께 이들의 선후관계 파악을 통한 제작기법 및 변질양상 등의 해석에도 활용 가능할 것으로 사료된다. 반면 시료채취 및 분말화 과정을 생략한 채 문화재시료 자체를 스캔하는 분석방법의 특성으로 인하여 특정 결정면의 정보가 강하게 중첩되는 경우가 일부 발생되었다. 이와 같은 회절패턴은 점토광물의 편향성효과와 같이 광물동정에 유리하게 활용되는 경우도 있으며, 단결정에 가까운 크기와 배열을 갖는 입자로 인하여 불규칙한 회절강도 비가 획득되어 컴퓨터 프로그램을 통한 광물동정이 어려운 경우가 있으므로 해석에 주의가 필요하다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.75-80
• /
• 1999

In this study, clay sampled from Yangsan$.$Mulkum site were used to analyze mineral properties. Mineral and chemical properties of clay were investigated through X-ray fluorescence spectrometer(XRF), X-Ray Diffraction(XRD), and Scanning Electron Microscope(SEM) analysis. The result of this test represents that Yangsan$.$Mulkum clay are composed of quartz, albite, anorthite, orthocalse and illite.

• Carbon letters
• /
• 제26권
• /
• pp.11-17
• /
• 2018

Milled carbon fiber (mCF) was prepared by a ball milling process, and X-ray diffraction (XRD) diffractograms were obtained by a $2{\theta}$ continuous scanning analysis to study mCF crystallinity as a function of milling time. The raw material for the mCF was polyacrylonitrile-based carbon fiber (T700). As the milling time increased, the mean particle size of the mCF consistently decreased, reaching $1.826{\mu}m$ at a milling time of 18 h. The XRD analysis showed that, as the milling time increased, the fraction of the crystalline carbon decreased, while the fraction of the amorphous carbon increased. The (002) peak became asymmetric before and after milling as the left side of the peak showed an increasingly gentle slope. For analysis, the asymmetric (002) peak was deconvoluted into two peaks, less-developed crystalline carbon (LDCC) and more-developed crystalline carbon. In both peaks, Lc decreased and $d_{002}$ increased, but no significant change was observed after 6 h of milling time. In addition, the fraction of LDCC increased. As the milling continued, the mCF became more amorphous, possibly due to damage to the crystal lattices by the milling.

• 한국전기전자재료학회논문지
• /
• 제14권4호
• /
• pp.269-273
• /
• 2001

W fabricated thin film using Na$_{0.5}$K$_{0.5}$NbO$_3$ volatile material by pulsed laser deposition (PLD) and studied characterization from EM, XRD, P-E. The density and scale of droplet, which is the defect of PLD, was investigated by SEM but large droplet was not found. The degree of assemble oriented C-axis measured with X-ray diffraction suggests that this film oriented C-axis achieved by $\theta$-2$\theta$ scan and rocking curves shows good self-assemble phenomenon, finally $\phi$-scan does that all of the four directions of the lattice in film equals to those of substrate. P-E hysteresis loop shows residual remnant polarization or saturation polarization value, but it is applicable to memories.ies.

• Journal of Korean Vacuum Science & Technology
• /
• 제4권2호
• /
• pp.50-54
• /
• 2000

We studied the synthesis of S $i_{1-x}$ Cx (x=0.016) epitaxial layer using ion implantation and solid phase epitaxy (SPE). The activation energy Ea was obtained for the loss of substitutional carbon using fourier transform-infrared spectroscopy (FTIR) and high-resolution x-ray diffraction (HR-XRD). In FTIR analysis, the integrated peak intensity was used to quantify the loss of carbon atoms from substitutional to interstitial sites during annealing. The substitutional carbon contents in S $i_{0.984}$ $C_{0.016}$ were also measured using HR-XRD. By dynamic simulations of x-ray rocking curves, the fraction of substitutional carbon was obtained. The effects of annealing temperature and time were also studied by comparing vacuum furnace annealing with rapid thermal annealing (RTA))))))

• The Journal of Advanced Prosthodontics
• /
• 제11권5호
• /
• pp.253-261
• /
• 2019

PURPOSE. To evaluate the influence of cyclic loading on phase transformation of zirconia abutments and to compare the effectiveness of three different quantitative ageing assessment techniques. MATERIALS AND METHODS. Thirty two Y-TZP prostheses fabricated from two brands, InCoris ZI and Ceramill ZI, were cemented to titanium bases and equally divided into two subgroups (n=8): control group without any treatment and aged group with cyclic loading between 20 N and 98 N for 100,000 cycles at 4 Hz in distilled water at $37^{\circ}C$. The tetragonal-to-monoclinic phase transformation was assessed by (i) conventional x-ray diffraction (XRD), (ii) micro x-ray diffraction (${\mu}XRD$), and (iii) micro-Raman spectroscopy. The monoclinic-phase fractions (M%) were compared by two-way ANOVA. RESULTS. InCoris Zi presented significantly higher M% than Ceramill Zi in both control and aged groups (P<.001). Both materials exhibited significant phase transformation with monoclinicphase of 1 to 3% more in aged groups than controls for all three assessment techniques. The comparable M% was quantified by both ${\mu}XRD$ and XRD. The highest M% was assessed with micro-Raman. CONCLUSION. Cyclic loading produced significant phase transformation in tested Y-TZP prostheses. The micro-Raman spectroscopy could be used as an alternative to XRD and ${\mu}XRD$.

• 한국세라믹학회지
• /
• 제49권5호
• /
• pp.469-474
• /
• 2012

The crystallinity and phase ratio of anatase to rutile in $TiO_2$ were estimated by x-ray diffraction (XRD) and x-ray absorption spectroscopy (XAS). Traditionally, the structural characterization of $TiO_2$ powders has been carried out by XRD techniques, which are comparatively easy in use and analysis. However, materials with amorphous phase, nano-sized or nano-structured crystallinities cannot be fully characterized by XRD because XRD analysis has a limit for abnormal contributions of the nano-crystal such as the surface contribution. From the comparison with the experimental and calculated Ti K-edge XAS spectra, we found the possibility of efficient estimation in the crystalinites and the phase ratio of anatase to rutile for nano-sized $TiO_2$ mixture.

• 한국화재소방학회논문지
• /
• 제29권6호
• /
• pp.76-83
• /
• 2015

EPS 샌드위치 패널은 난연제의 첨가로 화재 시 발화를 늦춰주며 발열을 적게 발생시켜 연소의 확대를 막는다. 하지만 난연성능 기준에 미달하는 샌드위치 패널을 사용할 경우, 재산 및 인명 피해가 확대되는 사례가 발생할 수 있다. 마감재료의 난연성능은 육안으로는 확인이 어려워 간편하면서도 빠른 평가방법의 개발이 요구된다. 본 연구에서는 X-선 분석법(XRF, XRD)을 이용하여 EPS 샌드위치 패널의 화재안전평가 방법에 대해 분석하였다. X-선 분석법을 적용한 결과 화재시험을 통한 난연 성능에 따라 특정 성분이 검출되는 것을 확인하였다. X-선 형광분석(XRF)을 통해 알루미늄성분이 부적합제품에 비해 적합제품에 훨씬 많이 함유되어있는 것을 알 수 있었다. X-선 회절분석(XRD)을 통해 난연 EPS의 주된 결정성 물질로 확인된 깁사이트(gibbsite)는 적합제품과 부적합제품에 공통으로 함유되어 있었지만 결정성에 있어 차이가 나는 것을 확인하였다. 이러한 X-선 분석을 통한 원소분석과 결정분석으로 난연성능 평가 가능성을 확인하였다.

• 대한토목학회논문집
• /
• 제26권1B호
• /
• pp.107-111
• /
• 2006

2종류의 제철 반응조에 있어서, 각종의 반응조건 하에 생성한 산화철을 x-ray회절과 M$\ddot{o}$ssbauer spectroscopy실험으로 철산화 물질을 동정한 결과, 여재 표면에 부착한 철 산화물의 결정은 pH 조건에 관계없이 Ferrihydrite($Fe_5HO_8{\cdot}4H_2O$)이었으며, Batch(회분) 실험에서 생긴 철 산화 물질은 가수분해에 의해 생긴 것으로, Microcrystalline Goethite 이었다.