• Journal of the Korean institute of surface engineering
• /
• v.34 no.2
• /
• pp.97-104
• /
• 2001

($Ti_{ 1-x}$$Al_{ x}$)N has been deposited on high speed steel (HSS) substrate using PECVD from the gas mixture of $TiC1_4$, $AlC1_4$, $NH_3$, $H_2$, and Ar. The correlation between the microstructure and the mechanical properties was investigated. ($Ti_{1-x}$$Al_{ x}$)N showed single phase NaCl-structure up to X=0.87, while a mixed phase of NaCl Type (Ti, Al) N and wurtzite structure AlN was observed for 0.87$Ti_{1-x}$ $Al_{x}$ )N became by degrees as increasing X, which made the hardness of the coating higher by Al addition. When the coating was composed of a mixed phase, however, the hardness decreased abruptly due to the effect of soft AlN phase. The wear volume of the coatings could be obtained as the concentration of the coating was varied, and the relation between the wear volume and hardness or the adhesion strength was discussed.

• Korean Journal of Materials Research
• /
• v.18 no.12
• /
• pp.640-644
• /
• 2008

ZnO/ZnS core/shell nanocrystals (${\sim}5-7\;nm$ in diameter) with a size close to the quantum confinement regime were successfully synthesized using polyol and thermolysis. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) analyses reveal that they exist in a highly crystalline wurtzite structure. The ZnO/ZnS nanocrystals show significantly enhanced UV-light emission (${\sim}384\;nm$) due to effective surface passivation of the ZnO core, whereas the emission of green light (${\sim}550\;nm$) was almost negligible. They also showed slight photoluminescence (PL) red-shift, which is possibly due to further growth of the ZnO core and/or the extension of the electron wave function to the shell. The ZnO/ZnS core/shell nanocrystals demonstrate strong potential for use as low-cost UV-light emitting devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.248-248
• /
• 2009

Recently, the control of size, morphology and dimensionality in inorganic materials has been rapidly developed into a promising field in materials chemistry. 3D nanostructured flower-like ZnO architecture with different size and shapes have been simply synthesized via a hydrothermal process, using zinc acetate and ammonium hydroxide as reactants.[1] In this study, the Zno thin-films were deposited by RF magnetron sputtering in other to get high adhesion and uniformity of 3D nanostructured flower-like ZnO architecture on a $SiO_2$ substrate. The XRD patterns identified that the obtained the nanocrystallized ZnO architecture exhibited a wurtzite structure. SEM images illustrated that the flower-like ZnO bundles consisted of flower-like or chestnut bur, which were characterized by polycrystalline and [0001] preferential orientation.

• Korean Journal of Materials Research
• /
• v.24 no.6
• /
• pp.301-304
• /
• 2014

The effect of oxygen pressure on the synthesis of ZnO nanowires by means of melt-oxidation of an Al-Zn mixture was investigated. The samples were prepared in oxygen ambient for 1 h at $1,000^{\circ}C$ under oxygen pressure ranging from 0.5 to 100 Torr. ZnO nanowires were formed at oxygen pressures lower than 10 Torr. As the oxygen pressure increased from 0.5 to 10 Torr, the width of the nanowires increased, but their length decreased. The ZnO nanowires had a needle shape, which became gradually thinner toward the tip. X-ray diffraction patterns showed that the nanowires had a hexagonal wurtzite structure. However, ZnO nanowires were not observed when the oxygen pressure increased from 10 Torr to 100 Torr. In roomtemperature cathodeluminescence spectra of the ZnO nanowires, the intensity of ultra-violet emission at 380 nm increased with decreasing oxygen pressure, which indicated that the lower the oxygen pressure, the better the crystallinity of the ZnO nanowires.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.8
• /
• pp.666-670
• /
• 2007

Aluminuim doped zinc oxide(ZnO:AL)Films have been prepared on Polyimide(PI) and Coming 7059 glass substrates by r.f. magnetron sputtering method. The structural of the ZnO:Al films were studied in accordance with various deposition R.F power and working pressure by XRD, SEM. And The electrical and optical properties of ZnO:Al films were characterized by Hall effect and UN visible spectrophotometer measurements, ZnO:Al films had were hexagonal wurtzite structure and dominant c-axis orientation. The R.f power and working pressure for optimum condition to fabricate the transparent conductive films using a PI substrate were 2 mTorr and 100W, respectively. The resistivity of the ZnO:Al films prepared under this condition were $9.6{\times}10^{-4}{\Omega}cm$. The optical transmittance of 400nm thick films at 550nm is ${\sim}85 %$.

• Korean Journal of Materials Research
• /
• v.21 no.4
• /
• pp.232-235
• /
• 2011

ZnO nanorods for gas sensors were prepared by a hydrothermal method. The ZnO gas sensors were fabricated on alumina substrates by a screen printing method. The gas-sensing properties of the ZnO nanorods were investigated for $CH_4$ gas. The effects of growth time on the structural and morphological properties of the ZnO nanorods were investigated by X-ray diffraction and scanning electron microscope. The XRD patterns of the nanocrystallized ZnO nanorods showed a wurtzite structure with the (002) predominant orientation. The diameter and length of the ZnO nanorods increased in proportion to the growth time. The sensitivity of the ZnO sensors to 5 ppm $CH_4$ gas was investigated for various growth times. The ZnO sensors exhibited good sensitivity and rapid response-recovery characteristics to $CH_4$ gas, and both traits were dependent on the growth time. The highest sensitivity of the ZnO sensors to $CH_4$ gas was observed with the growth time of 7 h. The response and recovery times were 13 s and 6 s, respectively.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.122-127
• /
• 1997

The hexagonal wurtzite structure of CdSe quantum dots are investigated by X-ray diffraction experiment. The absorption peaks due to quantum confinement effect are observed in the linear absorption spectra. Absorption coefficient changes at the lowest transition are measured with pump wavelength at the lowest transition and at the next higher transition from which direct intraband transition is not allowed. The measured larger absorption changes at the lowest transition confirm that the selection rules of intraband transition resulting from quantum confinement effect are satisfied. From the experimental results, therefore, we concluded that the CdSe quantum dots can be described as homogeneous system.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.1 s.34
• /
• pp.73-76
• /
• 2005

To widen the band gap of ZnO, we have investigated $Zn_{1-x}Mg_xO(ZMO)$ thin films prepared by pulsed laser deposition on c-plane sapphire substrates at $500^{\circ}C$. From X-ray diffraction patterns, ZMO films show only the (0002) and (0004) diffraction peaks. It means that the flints have the wurtzite structure. Segregation of ZnO and MgO phases is found in the films with x=0.59. All the samples are highly transparent in the visible region and have a sharp absorption edge in the UV region. The shift of absorption edge to higher energy is observed in the films with higher Mg composition. The excitonic nature of the films is clearly appeared in the spectra for all alloy compositions. The optical band-gap ($E_g$) of ZMO films is obtained from the ${\alpha}^2$ vs Photon energy plot assuming ${\alpha}^2\;\propto$ (hv - $E_g$), where u is the absorption coefficient and hv is the photon energy. The value of $E_g$ increases up to 3.72 eV for the films with x=0.35. It is important to adjust Mg composition control for controlling the band-gap of ZMO films.

• Korean Journal of Crystallography
• /
• v.14 no.2
• /
• pp.93-104
• /
• 2003

The crystals of group-Ⅲ nitride semiconductors with wurtzite structure exhibit a strong polarity. Especially, GaN has characteristics of different growth rate, anisotropic electrical and optical properties due to the polarity. In this work, GaN epilayer was grown and the polarities of the crystals were observed by the chemical wet etching and SP-EFM. GaN thin films were deposited on c-plane A1₂O₃ substrate under the variations of growth conditions by HVPE such as the deposition temperature of the buffer layer, the deposition time, the ratio of Group-V and Ⅲ and the deposition temperature of the film. The adquate results were obtained under the conditions of 500℃, 90 seconds, 1333 and 1080℃, respectively. It is observed that the GaN layer grown without the buffer layer has N-polarity and the GaN layer grown on the buffer layer has Ga-polarity. Fine crystal single particles were grown on c-plane A1₂O₃ and SiO₂, layer. The external shape of the crystal shows ｛10-11｝｛10-10｝(000-1) planes as expected in the PBC theory and anisotropic behavior along c-axis is obvious. As a result of etching on each plane, (000-1) and ｛10-11｝planes were etched strongly due to the N-polarity and ｛10-10｝ plane was not affected due to the non-polarity. In the case of the crystal grown on c-plane A1₂O₃, two types of crystals were grown. They were hexagonal pyramidal-shape with ｛10-11｝plane and hexagonal prism with basal plane. The latter might be grown by twin plane reentrant edge (TPRE) growth.

• The Korean Journal of Ceramics
• /
• v.5 no.3
• /
• pp.224-229
• /
• 1999

The preparation and toughening of SiC-AIN solid solution from powder mixtures of $\beta$-SiC, AIN and $\alpha$-SiC by hot-pressing were studied in the 1870 to $2030^{\circ}C$ temperature range. The reaction of AIN and $\beta$-SiC(3C) powders causing transformation to the 2H(wurtzite) structure appeared to depend on hot-pressing temperatures and an additive of $\alpha$-SiC. For the composition of 49wt% SiC with 2 wt% $\alpha$-SiC and 47.5 wt% AIN47.5wt% SiC with 5 wt % $\alpha$-SiC at 203$0^{\circ}C$ for 1 h, th complete solid solutions with a single phase of 2H could be obtained. The appreciable amount of $\alpha$-SiC could develop the columnar inter-grains of 4H phase and the stable 2H phase with the relatively uniform composition and grain size distributions. The effect of $\alpha$-SiC on the phases present and compositional microstructures with columnar inter-grains was invetigated using X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The fracture toughness and Vickers hardness of the hot-pressed solid solutions wre examined by the indentation-fracture-test method.