• 제목/요약/키워드: Worn wear

검색결과 607건 처리시간 0.028초

내하중성 첨가제의 따른 기어유의 마찰$cdot$마모 특성 (A Study on the friction and wear characteristics of gear oils with adding load carrying additives)

  • 최웅수;최주환;신성철;권오관;문탁진
    • Tribology and Lubricants
    • /
    • 제8권1호
    • /
    • pp.24-29
    • /
    • 1992
  • Friction and wear characteristics of gear oils added load carrying aditives, JS and DBP have been invesitigated using Shell Four Ball Tester and Cygnus and also compared with commercial gear oil. The Gear oil added DBP among them showed excellent friction and wear performances, which is deduced by action mechanism of additives. The surface analysis of the worn balls was conducted using an optical microscope.

표면이 마모된 틸팅 패드 저널베어링의 열윤활 해석 및 온도 측정 (Thermohydrodynamic Analysis and Pad Temperature Measurement of Tilting Pad Journal Bearing with Worn Pad)

  • 이동현;선경호;김병옥;강동혁
    • Tribology and Lubricants
    • /
    • 제33권4호
    • /
    • pp.134-140
    • /
    • 2017
  • With the increase in adoption of tilting pad journal bearings (TPJBs), various failure mechanisms related to TPJBs have been reported, of which pad wear is a frequently reported one. Pad wear causes change in geometry of the bearing, which can sometimes result in the failure of the entire system. The objective of this research is to investigate the influence of pad wear on the pad temperature, which is one of the widely used condition monitoring methods for TPJBs. For the theoretical investigation, thermohydrodynamic (THD) analysis was conducted by solving the generalized Reynolds equation and the 3D energy equation. The results of the analysis show that the temperature of the loaded pad increases while that of the unloaded pad decreases, when there is wear on the loaded pads. In addition, the minimum film thickness decreases with an increase in the wear depth. A validation test was conducted with a test rig, which mimics the axial turbine when a test rotor is supported by two TPJBs. The test bearing consists of five pads with a diameter of 60 mm, and a resistance temperature detector (RTD) is installed in the pad for temperature monitoring. The test was performed by replacing the two loaded pads with the worn pad. The test result for the TPJB with wear depth of $30{\mu}m$ show that the temperatures of the loaded pads are $8^{\circ}C$ higher and that of the unloaded pad is $2.5^{\circ}C$ lower than that of the normal TPJB. In addition, the predicted pad temperature shows good agreement with the measured pad temperatures.

5%Co-5%V-1%Nb 분말고속도공구강의 고온 미끄럼마모특성 (Sliding We3f Properties for 5%Co-5%V-1%Nb High Speed Steel by Powder Metallurgy at High Temperature)

  • 이한영;김용진;배종수
    • Tribology and Lubricants
    • /
    • 제19권3호
    • /
    • pp.151-158
    • /
    • 2003
  • In metal cutting at the tool-chip interface, friction generates considerable amount of heat. Thus, the knowledge of wear properties of cutting tool material in high temperature has been as one of important factors in need of clarification. The authors presented the wear properties of 5%Co-5%V-1%Nb high speed steel, fabricated by powder metallurgy, in room temperature in previous articles. The objective of this paper is to clarify the effects of temperature on its wear properties. Wear tests in sliding conditions under various temperatures have been conducted using the pin-on-disc type wear test machine. The results indicate that the wear properties of 5%Co-5%V-1%Nb high speed steel in high temperature as well as in room temperature are excellent. It may be deduced that the oxide layer formed on worn surface at high temperature is stable enough to prevent wear due to the high temperature strength of its matrix.

미끄럼 마찰하에서의 베어링간의 마모 diagram과 마모기구 (Wear diagram and Wear Mechanisms of Bearing Steel in Frictional Sliding)

  • 임대순;박성길;조성재;방건웅;문한규
    • Tribology and Lubricants
    • /
    • 제6권1호
    • /
    • pp.108-115
    • /
    • 1990
  • Wear diagrams, which are the three dimensional representations of the dependence of the wear rate on the applied pressure and the sliding speed, were constructed with the pin on ring type wear test results using 52100 wear couples. The pressure and speed ranges from 0.45 MPa to 45.30 MPa and from 0.012 m/sec to 0.12 (0.120)m/sec, respectively. The results show the mild to severe transition, which suggests the change of the wear mechanisms as a function of the pressure and sliding speed. The SEM micrographs of the corresponding worn area shows clearly that different wear mechanisms dominate.

컴프레서용 Al-Si 합금의 파괴 및 마모 특성 (Fracture and Wear Characteristics of Al-Si alloy used for Compressor)

  • 김재훈;김덕회
    • Tribology and Lubricants
    • /
    • 제15권2호
    • /
    • pp.141-149
    • /
    • 1999
  • Fracture, fatigue and wear characteristics of Al-Si alloy used for compressor are experimentally studied. Plane strain fracture toughness test is carried out using three point bending specimen. Fatigue test is performed under constant loading condition and wear test is carried out as a function of sliding velocity and applied load. To obtain the crack propagation characteristics and wear mechanism of Al-Si alloy, fracture and worn surfaces are investigated using SEM. It is verified that fracture and fatigue strength of Al-Si alloy are improved by the fine microstructure of alloy. The wear behavior and specific wear amount of Al-Si alloy are not dependent on the microstructure but on a function of the silicon content. Anodizing on the surface of Al-Si alloy, surface hardness and wear characteristics are improved.

재래형 콤포짓트 레진의 마찰 . 마멸거동 (Friction and Wear Behaviors of Conventional Composite Resins)

  • 임정일;서세광;김교한;김석삼
    • Tribology and Lubricants
    • /
    • 제16권3호
    • /
    • pp.166-172
    • /
    • 2000
  • The friction and wear characteristics of dental composite resins such as Charisma, Elitefil, TPH and Veridonfil were investigated. Furthermore, The surface characteristics examination, the analysis of contents of filler, Victors hardness and fracture toughness measurement of composite resins were preformed. The wear test applied ball to move reciprocationally on flat wear tester at room temperature. Microstructure of surfaces and worn surfaces were observed by SEM. Experimental results indicate that the friction coefficient of TPH was quite low, and the wear resistance of TPH was better than that of Charisma, Elitefil or Veridonfil at the same condition. The main wear mechanism was found to be plastic flow and abrasive wear by failure of filler's bond to the matrix.

남성 Vest의 기원과 변천과정에 관한 연구 (A Study on the Origin and the Developing Process of Vest for Men)

  • 김서영;이순홍
    • 복식문화연구
    • /
    • 제6권3호
    • /
    • pp.56-72
    • /
    • 1998
  • Vest is a general term for a sleeveless upper garment and it derives from a kolobus of a sleeveless tunic style that was started to be worn as a substitution of a chiton by the peasantry in Greek period. The kolobus started to be called a colobium or a tunica from Roman period and the former was named for a vest style tunica which was worn by the people of the lower classes in early Roman period. Similarly, a German colobium of North Europe which was worn during the same period was the same kind of clothe as the Roman colobium. The colobium came to be worn over a dalmatica as an outer garment by early Christians when it was the Middle Ages, who succeeded the tradition of colobium as they went through ancient Rome, Creek and Byzantine days. North Germans also succeeded the colobium tradition of ancient Germans as it was and so continued to wear it in tight style. The simple vest style of colobium was getting vanished from the mid of the Middle Agnes and a new style of vest named jupon was started to be worn by soldiers. The jupon was to protect soldiers' bodies from either were cold weather or enemies wearing under armors as it was made with double cotton pad by quilt. From 14th century, the jupon began to be worn by not only soldiers but also the humble of lower classes. All the jupon which were made in quilting and padding of that time began to be named a pourpoint by the humble. When Renaissance in 16th century came, the pourpoint began to be developed to an exaggerating body-line style. The neckline of pourpoint was getting highly influenced by Spain and a peacecod-belly of it emphasized the exaggerated masculine beauty of Renaissance by padding in round. The sleeves were puffed out and the whole purpoint was made to expose an inner chemise by slashing vertically or obliquely. But in 17th century, the pourpoint has been changed into more simple style without padding, puffing out and slashing influenced by the citizens' clothes of Netherlands. The pourpoint came to be more comfortable bulky style with short sleeves or sleeveless and straight side lines. The pourpoint in mid 17th century turned to be a bolero jacket style by gradually being tightened. It had been then changed into a vest style with sleeves and worn under an overcoat with the name of vest in the end of 17th century. The early vest was 2∼3 inches les in length than the overcoat and had long sleeves and many ornamental buttons on front. It was also made as a home wear to be worn it alone at home. In 18th century, the length of the vest became shorter compared with that of 17th century and the most important decorative item in clothes. It again came to have complete sleeveless vest style and had very short length reaching waist in the end of 18th century. When it was in 19th century, the vest had developed into more various style and colors and style had been applied to be worn by individuals with their tastes. Around the end of 19th century, the increasing tendency to be casual by industrialization influenced on clothes in all aspects of life and so the male vest has been gradually changed into more casual style. Nowadays, it has been developing into various uses in modern male clothes to show their characters.

  • PDF

현대여성(現代女性)의 의복의식(衣服意識)에 관한 조사(調査) 연구(硏究) - 서울 지역(地域)의 양복(洋服) 착용자(着用者)를 중심(中心)으로 -

  • 이희명
    • 복식
    • /
    • 제2권
    • /
    • pp.73-88
    • /
    • 1978
  • This article is an attempt to explain, at least in part, the contemporary Korean women's consciousness of Western Dreasses. As time changes, the role of clothing undergoes varisous transitions, while values and ways of life are constantly in change. It is, therefore, proper and appropriate to recognize as among the major aspects of social psychology such phenomenon as interests, understanding of clothing, the choice of a dress, and attitudes toward clothing, etc. The purpose of this study is to discover problems concerning and their clothing and their solutions, by means of a surveying approach. The method of research used is based upon questionares distributed to parents of first-year pupils in elementary schools and to female clerks working in offices, covering the period from August through October, 1976. The number of the questionares distrubuted totalled 600, and 526 were returned to the research to be utilized for analysis. The contents of the survey included such things as values concerning clothing, kinds of clothing and their practical use, the selection of clothing and the method of purchase, fashions, etc. The classification of aquisition are self-made clothing, clothing made to order and ready-made materials. It is composed of 25 items, including affirmative reasons as well as negative ones. The processing of the material returned was made by using the computer, and based upon classifications such as ages, monthly income, occupations; thus diagraming the result in percentages. The conclusion made and the improvements proposed are as follows: 1. The values of clothing were placed on the expression of the wearer's personality (32.7) and on eauty(28. 6%). The lower age group places is stress upon the expression of personality, while the higher age group stresses beauty. About 50% of wearers are contented with their clothing, their clothing, the rest of whom them indicating their dissatisfaction with what they wear. As to designs at the time of selection, about 46% indicated their preference of personal expression, 31.8% on usefulness. In selecting material, practicality is emphasized; in selecting patterns, single color is preferred. In short, personal expression and esthetic values are primary, with consideration of practicality in mind. 2. The classification of clothing according to their uses indicates the highest numbers in normal wear (home wears) and clothings to be worn outside home. As to evening dresses, (party dress) only one or two articles were checked by many, and no such article was clamed to be possessed by most. The highest ratio of wearing was shown in the case of home wear (47.3%) and clothing to be worn outside the home, which is 55.8%. The budget for one article of clothing was greatest in the case of home wear, and clothing worn outside the home. Many used both kinds of articles for the same purpose. It is desirable, therefore, that the kinds of clothing should be varied according to the purpose for which they are worn, and that clothing appropriate for that purpose should be worn. 3. The motivation for purchasing clothing was highly chosen in the item of seasonal change, which was 55.7%; Clothing deliberately made was indicated by 45.2%. In the mothods of purchasing clothing, clothing made to order and ready-made was indicated by 44.4%, which is the highest; Clothing made to order was 25.4%, and self-sewing was 1.1%, which is the lowest. (1) In the case of self-sewing, "I like it but it is very hard," was checked by 43.6%; "It is so difficult that I cannot wear such clothing" was checked by 13.3%. From these, we can conclude that the questionees are willing to make clothing by themselves, but techniques involved in sewing and at her problems involved in the skill are complicated but when those problems are eliminated there is a possibility for practice. The response checked by questionees concerning the self-sewing was, "It's economical", which is a clear indication that many questionees are positive for self-sewing. It is generally believed that ready-made clothing is cheaper, but it is not necessarily so. In consideration of the quality of clothing, self-sewing is a necessity, and it is desirable that it should be encouraged. (3) Problems involved in ready-made clothing, such as designs, skills, size (fitting) should be eliminated. When these problems are scientifically gotten rid of, it is possible that affirmative returns will be expected. Affirmative responses such as "Ready-made clothing is economical," "You can select there on the spot," are good signs that many women expect to wear ready-made clothing. It is in this sense that the prospect for ready-made clothing is brighter when much development for ready-made clothing is on the way. 4. Much concern for fashion are checked in such item of questions as "Fashionable clothing in the show window," "Clothes worn by women." The first item was checked by 50.1 %, and the second was checked by 48.6%. The reason for following fashion is "Because many people wear them," which was indicated by 30.4%. The reason for not following fashion is "It is too expensive," which was checked by 29.6%. The 26.2% of the answers indicated that "Fashionable clothing is devoid of personality," The influences of fashion over the development of fashion over the development of clothing are two-fold: Esthetic and active. It is not to be deniable that people follow fashion more or less. 1978.9>

  • PDF

다합금 백주철의 미끄럼 마모특성에 미치는 코발트 첨가의 영향 (The Effects of Cobalt Addition on Sliding Wear Properties of Multi-component White Cast Iron)

  • 이한영
    • 한국주조공학회지
    • /
    • 제24권4호
    • /
    • pp.202-208
    • /
    • 2004
  • Effects of Co addition on sliding wear properties of multi-component white cast iron were investigated. The microstructures of multi-component white cast iron containing from 0%Co to 10%Co exhibited little difference. However, the hardness increased with an increase of the Co content. Increasing the Co content, wear properties were improved and the iron oxide on worn surface was increased in the low sliding speed range of the steady-state wear region. Hence, Co addition was effective to improve the wear properties of multi-component white cast iron by accelerating the corrosive wear as well as the enhancement effect of hardness.

PMMA(Poly Methyl Methacrylate) 코팅층 두께 및 적용하중에 따른 마멸기구 분석 (Effects of thickness and applied load on wear mechanisms of PMMA (Poly Methyl Methacrylate) coating layers)

  • 강석하;김용석
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2004년도 춘계학술대회 논문집
    • /
    • pp.152-155
    • /
    • 2004
  • Effects of sliding speed, applied load, counterpart radius and thickness of PMMA (Poly Methyl Methacrylate) coating layers on their dry sliding frictional and wear behavior were investigated. Sliding wear tests were carried out using a pin-on-disk wear tester. The PMMA layer was coated on Si wafer by a sol-gel technique with two different thicknesses, $1.5{\mu}m\;and\;0.8{\mu}m$. AISI 52100 bearing steel balls were used as a counterpart of the PMMA coating during the wear. Normal applied load and sliding speed were varied. Wear mechanisms were investigated by examining worn surfaces by an SEM. Under most of sliding test conditions, the thicker layer with the thickness of $1.5{\mu}m$ showed lower fiction coefficient than the thinner layer. Effects of sliding speed and counterpart's radius on the frictional behavior were varied depending on the thickness of the coating layer.

  • PDF