• Journal of Bio-Environment Control
• /
• v.31 no.2
• /
• pp.79-89
• /
• 2022

With the wide use of greenhouses, the working hours have been increasing inside the greenhouse for workers. In the closed ventilated greenhouse, the internal environment has less affected to external weather during making a suitable temperature for crop growth. Greenhouse workers are exposed to organic dust including soil dust, pollen, pesticide residues, microorganisms during tillage process, soil grading, fertilizing, and harvesting operations. Therefore, the health status and working environment exposed to workers should be considered inside the greenhouse. It is necessary to secure basic data on particulate matter (PM) concentrations in order to set up dust reduction and health safety plans. To understand the PM concentration of working environment in greenhouse, the PM concnentrations were monitored in the cut-rose and Hallabong greenhouses in terms of PM size, working type, and working period. Compare to no-work (move) period, a significant increase in PM concentration was found during tillage operation in Hallabong greenhouse by 4.94 times on TSP (total suspended particle), 2.71 times on PM-10 (particle size of 10 ㎛ or larger), and 1.53 times on PM-2.5, respectively. During pruning operation in cut-rose greenhouse, TSP concentration was 7.4 times higher and PM-10 concentration was 3.2 times higher than during no-work period. As a result of analysis of PM contribution ratio by particle sizes, it was shown that PM-10 constitute the largest percentage. There was a significant difference in the PM concentration between work and no-work periods, and the concentration of PM during work was significant higher (p < 0.001). It was found that workers were generally exposed to a high level of dust concentration from 2.5 ㎛ to 35.15 ㎛ during tillage operation.

• Journal of Navigation and Port Research
• /
• v.31 no.3 s.119
• /
• pp.247-252
• /
• 2007

The container crane is one of the most important equipments at container terminal. If its working time in cycle could be reduced then container terminal efficiency and service level can be increased. So there are many i1forts to reduce working time of container cranes. It means how to design the controller with good performance which has small overshoot and swing motion of container crane. We, in this paper, present a state feedback controller based on LQ theory incorporating a RCGA which means real-coded genetic algorithm RCGA can search state feedback gains under given objective function. A set of simulation works are carried out in order to prove the control effectiveness of the proposed methods.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.1
• /
• pp.15-19
• /
• 2008

The most typical capping method for concrete structures is a sulfur-mortar compound capping, provided it satisfied the standard criterion set forth by ASTM C 617, but this conventional bonded-type method has many problems. It exhibits relatively the smaller unreliable value of the strength of high-strength concrete due to the differences of elasticity and strength between the cylinder and the cap, and manifests poor serviceability such as dangerous working tasks or a waste of the working time. To prevent these problems, unbonded-type capping methods have taken the place of the conventional methods in recent years. One of the popular methods is the use of synthetic rubber like a neoprene pad. Serious problems still remain in this method, which include the consideration of its chemical characteristics in consideration of the selection, the safekeeping and the economy of the pads. Moreover, the synthetic rubber pads cannot be used in concrete cylinder with strength greater than 80 MPa according to ASTM C 1231-00. New 'sand-capping method' presented in this study, can be applicable to the compressive strength evaluation of the high strength concrete in the range of $70{\sim}100\;MPa$. This new method has better simplicity and reliability than those of existing 'sand-box', because usual materials such as standard sand and simply-devised apparatus are used for the capping system. The statistical analysis of the test results revealed that the new sand-capping method exhibited the smallest deviation and dispersion, attesting for its much better reliability than other methods specified in ASTM C 1231/1231M.

• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.54-58
• /
• 2016

In this research paper, suggest method of generate same bead as an actual measurement data in virtual welding conditions, exploit morphology information of the bead that acquired through robot welding. It has many multiple risk factors to Beginners welding training, by we make possible to train welding in virtual reality, we can reduce welding training risk and welding material to exploit bead visualization algorithm that we suggest so it will be expected to achieve educational, environmental and economical effect. The proposed method is acquire data to each case performing robot welding by set the voltage, current, working angle, process angle, speed and arc length of welding condition value. As Welding condition value is most important thing in decide bead form, we would selected one of baseline each item and then acquired metal followed another factors change. Welding type is FCAW, SMAW and TIG. When welding trainee perform the training, it's difficult to save all of changed information into database likewise working angle, process angle, speed and arc length. So not saving data into database are applying the method to infer the form of bead using a neural network algorithm. The way of bead's visualization is applying the spline algorithm. To accurately represent Morphological information of the bead, requires much of morphological information, so it can occur problem to save into database that is why we using the spline algorithm. By applying the spline algorithm, it can make simplified data and generate accurate bead shape. Through the research paper, the shape of bead generated by the virtual reality was able to improve the accuracy when compared using the form of bead generated by the robot welding to using the morphological information of the bead generated through the robot welding. By express the accurate shape of bead and so can reduce the difference of the actual welding training and virtual welding, it was confirmed that it can be performed safety and high effective virtual welding education.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• autumn
• /
• pp.614-617
• /
• 2003

Recently the demand of constructing high-rised building grows larger. So it becomes more important to make an exact plan of a tower cranes which has an important position in high-rised building construction. Nevertheless businessmen of construction sites only depend on a great store of experience without a clear process of locating tower cranes. The object of this study is to set up the process model for locating tower cranes. The study went off through a study of related documents, an interview with some experts and a visiting of job sites. In result the study suggests a process model which has four steps of considering an establishing, disjointing, a radius of working, easy working. Case study was examined to estimate the feasibility and applicability of the proposed model. As a result, the model is proven to be a method to locate tower cranes quickly and cleary, and to operate properly as a decision-making tool.

• Journal of Biosystems Engineering
• /
• v.28 no.3
• /
• pp.199-208
• /
• 2003

In order to solve the shortage of roughage supply for dairy farm in Korea, winter cereal forage production after harvesting of rice in the fallow paddy field is studied. This study consist of two parts. One is the model development of the mechanized production which was already reported at the preview paper. This is the 2nd parts of the study. Also, the mechanized production model for cereal forage production in winter was reported in the previous study. In this paper, coverage area and mechanized wrap silge production cost are analyzed and compared to the other available feeds in Korea. Results of the research are summarized as follows; The coverage area for the winter cereal wrap silage production system in Korea is estimated to be 33.7 ha in case of working with a tractor and a set of implements. If two or three tractors are available, the coverage area is estimated to be 68.0 and 101.3 ha, respectively. The break even point (BEP) of the farming size is analyzed as 10 ha and its production(operating) cost is estimated to be 317 to 443 won/TDN-kg at the BEP point. The cost is lowered to 182 won/TDN-kg at 100ha-working, and is much lower compared with prices of imported feeds of 360∼600 won/TDN-kg. Therefore, winter cereal wrap silage model is judged to be feasible and desirable for a large scale production of forage in winter fallow paddy field.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.119-128
• /
• 1993

Effective machine capacity is affected by the physical and geometrical conditions of the fields. In the small and scattered farmland structure field efficiency is greatly influenced by plot geometry. In this paper, a method for estimating field efficiency and effective machine capacity was developed . The developed method was applied to Korean paddy cultivation. Various time elements related to farm operations for small and scattered plots are discussed in this paper . Available working time is divided into two parts, viz. the preparation time for machine operation and actual working time. Two kinds of machine efficiencies, namely , Machine Efficiency 1, applicable on a single large plot or set of well consolidated plots ; and Machine Efficiency 2, applicable on small and scattered multiple plots, are considered. Based assumptions made and steps followed to construct the model are discussed. Effective capacity of each machine based on different plot geometries are calculated y the model. Machine efficiency on a single plot increases with increase in the dimension of longer side of the plot . Low speed, low theoretical capacity machines have higher machine efficiency which is only slightly influenced by plot geometry. As plot geometry is improved , the machine efficiency of high speed, high capacity machines increases rapidly. The effects of short side length and plot size on machine efficiency on a single plot depend on the type of farm operation. For a particular plot shape, as plot size increases, machine efficiency on multiple plots increases rapidly. The effects of consolidation on machine efficiency is highly significant if the plot size is small and/or machine size is large.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.13-20
• /
• 2004

In order to set up the design of micro optical bench, optical coupling efficiencies of two sets of test benches are calculated. Simple linear connections of incoming and outgoing optical fibers with and without ball lenses are designed. Positional errors that are possible in actual fabrication processes we considered in the calculations and their tolerances are determined from -3 ㏈ conditions. For a simple fiber-to-fiber connection, the lateral misalignment should be limited to 2.7 um and tilt error 5.8o. In case of the fiber-to-fiber with ball lens, the working distance between fibers can be extended over 60 um. The optical coupling efficiency depends strongly on the positional errors of ball lenses along the optical axis, and it is also found that the lateral and vertical positional errors should be considered simultaneously in order to keep the high coupling efficiency.

• Journal of the Korean Society of Costume
• /
• v.60 no.6
• /
• pp.23-36
• /
• 2010

This study set out to develop clothes made of electromagnetic wave shielding materials. Among the various worker groups exposed to electromagnetic waves for long hours, railroad workers were chosen for the study. After selecting the locations they worked, the investigator measured electromagnetic wave on the field. To examine the effects of electromagnetic wave shielding materials, I applied a lining made of electromagnetic wave shielding materials to the existing work clothes. The first experimental clothes had the silver fabric for the lining in the current working clothes, the second experimental clothes had the copper- and nickel-plate polyester placed between the outer and the lining to prevent the corrosive material from contacting the skin, and the third experimental clothes had the silver fabric for the lining and the copper- and nickel-plate polyester between the outer and the lining. The results indicate that even if a fabric is evaluated to shield electromagnetic waves after tests, it cannot completely shield electromagnetic waves emitting from everyday appliances of 60Hz. Therefore, there should be ongoing development and research efforts on fabrics that can shield electromagnetic waves to a certain degree in order to develop working clothes to alleviate fatigue for those who are constantly exposed to electromagnetic waves, relieve their anxiety, offer them psychological stability and thus help them increase job efficiency.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.4
• /
• pp.45-50
• /
• 2014

In this paper, the Ocean Thermal Energy Conversion(OTEC) with vapor-vapor ejector is proposed newly. At this OTEC system, a vapor-vapor ejector is installed at inlet of condenser. The vapor-vapor ejector plays a very important role in increasing of the production work of low-stage turbine throughout the decrement of outlet pressure of ejector. The performance analysis is conducted for optimizing the system with HYSYS program. The procedure of performance analysis consists of outlet pressure of high turbine, the mass ratio of working fluid at separator, total working fluid rate, and nozzle diameters of vapor-vapor ejector. The main results is summarized as follows. The nozzle diameter is most important thing in this study. When each nozzle diameter of vapor-vapor ejector is 10 mm, the efficiency of OTEC system with vapor-vapor ejector shows the highest value. So it is necessary to set the optimized nozzle diameters of vapor-vapor ejector for achieving the high efficiency OTEC power system.