• Journal of the Korean Magnetics Society
• /
• v.26 no.1
• /
• pp.19-23
• /
• 2016

In this study, we have constructed a measuring system to investigate tensile stress measurement of tendons, which is employed in bridges, by means of the non-destructive and non-contact method. The measuring system consists of tensile stress applying apparatus up to 2 GPa, and power supply for ac and dc current to tendon directly to magnetize tendon in circular direction and to coil wound on yoke to magnetize tendon in axial direction. We have used two kinds of tendon, which were produced by different companies, using the measuring system constructed in this work. Two kinds of experiments are carried out in this work; $1^{st}$ experiment : ac current was applied to the tendon and dc current was applied to coil wound on the yoke, and voltage induced from search coil wound on yoke (SCY) was measured and $2^{nd}$ experiment : dc current was applied to the tendon and ac current was applied to coil wound on the yoke, and voltage induced from search coil on tendon (SCT) was measured. In case of $1^{st}$ experiment, voltage induced from SCY was changed below 200MPa tensile stress but the voltage was not increased above 200 MPa. In case of $2^{nd}$ experiment, voltage induced from SCT was decreased up to 1.5 GPa linearly. We expect that $2^{nd}$ experiment could be applied to the non-destructive testing of tensile stress measurement of tendon.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.2
• /
• pp.117-124
• /
• 1993

It was found that the basic principle of continuous crystal growth method was following as; the powder supplied from the feeding system is molten in the graphite crucible under the ambient gas. After forming the molten zone in the lower part of the crucible, the seed crystal is deeped into the melt and pulled down with the rotation so that the melt crystallized from the seed. When the lowering rate, rotation rate, feeding rate and temperature are correct, the single crystal can grow. The critical melt level, the feeding rate, the growth rate, the change of the shape of molten zone by the graphite susceptor and crucible, the position of work coil, the balance between the gravitational force of melt and the centrifugal force originated from the rotation of seed which are the variables of the crystal growth and the sintering phenomenon of melt surface were researched.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.6
• /
• pp.505-510
• /
• 2013

An encircling send-receive type pulsed eddy current (PEC) probe is designed for use in aluminum tube inspection. When bare receive coils located away from the exciter were used, the peak time of the signal did not change although the distance from the exciter increased. This is because the magnetic flux from the exciter coil directly affects the receive coil signal. Therefore, in this work, both the exciter and the sensor coils were shielded in order to reduce the influence of direct flux from the exciter coil. Numerical simulation with the designed shielded encircling PEC probe showed the corresponding increase of the peak time as the sensor distance increased. Ferrite and carbon steel shields were compared and results of the ferrite shielding showed a slightly stronger peak value and a quicker peak time than those of the carbon steel shielding. Simulation results showed that the peak value increased as the defect size (such as depth and length) increased regardless of the sensor location. To decide a proper sensor location, the sensitivity of the peak value to defect size variation was investigated and found that the normalized peak value was more sensitive to defect size variation when the sensor was located closer to the exciter.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.785-788
• /
• 2005

In this study, micro-scale, high-performance, solenoid-type RF chip inductors were investigated. The size of the RF chip inductors fabricated in this work was $1.0{\times}0.5{\times}0.5mm^3$ The material and shape of the core were 96% $Al_2O_3$ and I-type. The material and number of turn of coil were copper (Cu) and 6. The diameter ($40{\mu}m$) of coil and length (0.35mm) of solenoid were determined by a Maxwell three-dimensional field simulator to maximize the performance of the inductors. High frequency characteristics of the inductance (L) and quality-factor (Q) of developed inductors were measured using an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). The inductors developed have inductances of 10.8nH and quality factors of 25.2 at 250MHz, and show results comparable to those measured for the inductors prepared by CoilCraftTm that is one of the best chip inductor company in the world. The simulated data predicted the high-frequency data of the Land Q of the inductors developed well.

• Journal of electromagnetic engineering and science
• /
• v.18 no.1
• /
• pp.13-19
• /
• 2018

Wireless power transfer (WPT) based on magnetic resonant coupling is a promising technology in many industrial applications. Efficiency of the WPT system usually depends on the tilt angle of the transmitter or the receiver coil. This work analyzes the effect of the tilt angle on the efficiency of the WPT system with horizontal misalignment. The mutual inductance between two coils located at arbitrary positions with tilt angles is calculated using a numerical analysis based on the Neumann formula. The efficiency of the WPT system with a tilted coil is extracted using an equivalent circuit model with extracted mutual inductance. By analyzing the results, we propose an optimal tilt angle to maximize the efficiency of the WPT system. The best angle to maximize the efficiency depends on the radii of the two coils and their relative position. The calculated efficiencies versus the tilt angle for various WPT cases, which change the radius of RX ($r_2=0.075m$, 0.1 m, 0.15 m) and the horizontal distance (y=0 m, 0.05 m, 0.1 m), are compared with the experimental results. The analytically extracted efficiencies and the extracted optimal tilt angles agree well with those of the experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.2
• /
• pp.250-255
• /
• 2008

Springs are widely utilized in machine element. To find out stiffness of frustum-shaped coil spring, the space beam theory using the finite element method is adopted in this paper. In three dimensional space, a space frame element is a straight bar of uniform cross section which is capable of resisting axial forces, bending moments about two principal axes in the plane of its cross section and twisting moment about its centroidal axis. The corresponding displacement degrees of freedom are twelve. To find out load vector of coil spring subjected to distributed compression. principle of virtual work is adapted. And this theory was programming using MATLAB software. To compare FEM using MATLAB software was applied MSC. Nastran software. The geometry model for MSC. Patran was produced by 3-D design modeling software. Finite element model was produced by MSC. Patran. Finite element was applied tetra (CTETRA) having 10 node. The analysis results of the MATLAB and MSC. Nastran are fairly well agreed with those of various experiments. Using MATLAB program proposed in this paper and MSC. Nastran, spring constants and stresses can be predicted by input of few factors.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.5
• /
• pp.497-502
• /
• 1997

In this study an automatic rolling-coil labeling system using robot vision system and peripheral mechanism is proposed and implemented, which instead of the manual labor to attach labels Rolling-coils in a steel mill. The binary image process for the image processing is performed with the threshold, and the contour line is converted to the binary gradient which detects the discontinuous variation of brightness of rolling-coils. The moments invariant algorithm proposed by Hu is used to make it easy to recognize even when the position of the center are different from the trained data. The position error compensation algorithm of six degrees of freedom industrial robot manipulator is also developed and the data of the position of the center rolling-coils, which is obtained by floor mount camera, are transferred by asynchronous communication method. Therefore, even if the position of center is changed, robot moves to the position of center and performs the labeling work successfully. Therefore, this system can be improved the safety and efficiency.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.144-146
• /
• 2005

Dual electromagnetic sensor is used for sensing the weld line. The sensor consists of excitation and two sensing coil wound over the ferro-magnetic core. By using the dual sensor, the effect of noise is minimized. It is based on the generation of eddy currents in the welding plate by passing current through the excitation coil. The sensor can be used to track the butt joints having no gap between them, where a vision based sensor fails to track. Sensor sensitivity depends on the number of coil turns, frequency of excitation, distance of a sensor from the work piece, diameter of core, etc. The whole system consists of a sensor, a signal processing board, a motion controller and a personnel computer (PC). The raw sensor signal is processed using the signal processing board. It consists of amplification, rectification, filtering, averaging, offset adjustment, etc. Based on sensor data, the motion controller adjusts the position of a welding torch.

• Journal of the Institute of Convergence Signal Processing
• /
• v.1 no.1
• /
• pp.89-96
• /
• 2000

In this paper, we propose a vision algorithm for the inspection of very small RF-chip inductor which is used in mobile-communication terminal. The proposed method divides coil part from the inductor body by local adaptive thresholding and integral projection method. After dividing work, the coil components are extracted by thinning and labelling techniques. The test items are the number of turns, the intervals in coil, and the measure of uniformity between the extracted lines. If the values of these are more than the specific value a tested product is decided bad one. In the simulation, the proposed method has a good performance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.3
• /
• pp.282-291
• /
• 1998

Heat transfer performance are studied for the turbulent flow of water in 3 smooth tube coils having ratios of coil to tube diameter of 16, 21 and 27, and a corrugated-coiled tube having a ratio of coil to tube diameter of 29, for Reynolds numbers from 8000 to 60000 and is also compared with the limited results available to data. The experiments are carried out for the fully developed turbulent flow of water in tube coils under the condition of uniform heat flux. This work is limited 0 tube coils of R/a between 10 and 30. The tube having a ratio of coil to tube diameter of 27 among the 3 smooth tube coils shows the best heat transfer performance. The performance of coiled tube best transfer performance. The performance of coiled tube with a similar curvature ratio is better for a corrugated-coiled tube(R/a=17) than for a smooth coiled tube(R/a=16). An empirical relation which correlates most of the data within $\pm$25% was also developed. Test result shows that the Nusselt number is found to be affected by a secondary flow due to curvature.