• Journal of the Korean Wood Science and Technology
• /
• v.18 no.2
• /
• pp.8-15
• /
• 1990

This study was carried out to investigate the wood qualities for the end-use development of sycamore (Platanus occidentalis L.) grown in Korea. The results obtained were as follows: 1. The average length of wood fibers was l.56mm and the average width of annual rings was 9.5mm. It had very fast growth rate. 2. The specific gravity in air-dry was 0.66. The shrinkage and water absorption were relatively large. The shear and impact strengthes were very strong, while the compressive, tensile, and bending strengthes were weak in comparison to it's specific gravity. 3. The contents of ash, holocellulose, lignin were relatively high 0.74%, 83.08%, 28.79%, but that of pentosan was low 18.53%. 4. The expected uses of sycamore wood are plywood. fancy veneer, small furniture, musical instrument, door and window frame, tool handels, boxes, etc.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.1-6
• /
• 1996

This study was performed to investigate the feasibility of using sonic stress-wave technique in the longitudinal direction for the assessment of incipient decay of radiata pine wood. Decayed bending specimens by Tyromyces palustris and Gloeophyllum trabeum for varoious periods were tested nondestructively using stress-wave technique in the longitudinal direction and destructively. Decay detection, quantitative assessment of decay, and the prediction of residual strength of decayed wood with less than five percent weight loss can be feasible using stress-wave parameters (wave velocity, wave impedance, stress-wave elasticity) measured by stress-wave technique in the longitudinal direction and their percent reduction due to decay.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.363-369
• /
• 2018

This study measured the mechanical properties of an ash wood under various temperature and humidity conditions and a finite element model was developed to predict the behavior of the wood. A humidity-controlled chamber was developed and used for measuring the dimensional changes of woods under various humidity conditions. The thermal expansion coefficient and the elastic stiffness constants were measured by using a thermal chamber and the three-point bending test along the three principal axes of the wood. A constitutive model was proposed to describe the moisture content and temperature dependent behavior of wood. The proposed model was validated for the warping test of a wood plate. The warping of the plate was calculated using the finite element method. The calculated amount of warping was in consistence with the measurements.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.301-308
• /
• 2014

Despite Korea forest take 63.7% of the nation's territory, productivity of domestic structural lumber is low. Studies of domestic small lumbers need to be improved domestic structural timber productivity. In this study, small diameter lumber and finger joint small diameter lumber took bending test to calculate MOE and MOR. MOE of small diameter lumber was $9.3kN/mm^2$ and MOE of finger joint small diameter lumber was $15.4kN/mm^2$. Allowable standard bending stress of small diameter lumber and finger joint small diameter lumber was calculated according to ASTM D 2915. Standard allowable bending stress of small diameter lumber was $12N/mm^2$ and standard allowable bending stress of finger joint small diameter lumber was $11N/mm^2$. Standard allowable bending stress of finger joint small diameter lumber should be considered to design structural beam members.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.42-49
• /
• 2003

The objective of this research was to investigate the possibility of using rice husk flour as a partial substitute for the wood particles used as the raw material for manufacturing particleboards, by examining the physical and mechanical properties of the rice husk flour-wood particleboard as a function of the type of urea-formaldehyde resin used. Commercial wood particles and two types of rice husk flours (A type (30 ㎛), B type (300 ㎛)) were used. E₁ and E₂ class urea-formaldehyde resin was used as the composite binder, combined with 10 wt.% NH₄Cl solution as a hardener. Rice husk flour-wood particleboards with dimensions of 27×27×0.7 (cm) were manufactured at a specific gravity of 0.7 with rice husk flour contents of 0, 5, 10, and 15 (wt.%). We examined the physical properties (specific gravity and moisture content), mechanical properties (three point bending strength and internal bonding) of the composite. In general, it can be concluded that composites made from rice husk flours are of somewhat poorer quality than those made from wood; however, blending in small amounts of rice husk flour (e.g., 5% to 10% by weight) may have no significant impact on quality.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.3
• /
• pp.299-310
• /
• 2019

This study was carried out to investigate the effect of heat-treatment and particle size on the crystalline properties of the wood cellulose. The color of wood flours was changed from light yellow in control sample to dark yellow or deep brown by heat treatment at $100^{\circ}C$ to $200^{\circ}C$. Relative crystallinity of the heat treated wood cellulose decreased with decreasing particle size from wood chips to 200 mesh, and there was little change in the crystal width. As the temperature was increased, relative crystallinity of the wood increased and crystal width was not changed. As a result of the FT-IR analysis, it was confirmed that the peaks were gradually decreased at -OH elongation as the heat-treated temperature was increased. The lignin C-H bending of $1425cm^{-1}$ and the hemicellulose C-H bending of $1370cm^{-1}$ did not change with the increase of the heat treatment temperature. In addition, it was revealed that C-C stretching of carbohydrate near $1031cm^{-1}$ decreased with increasing heat treatment temperature. Consequently, it is suggested that particle size and heat treatment affected the crystalline properties of wood cellulose.

• Nuclear Engineering and Technology
• /
• v.5 no.2
• /
• pp.150-158
• /
• 1973

General physical properties and radiation durabilities of some domestic woods and imported lauans were measured and discussed as a preliminary study on the preparation of W. P. C. The data obtained indicate that 1) the hardness of wood is generally proportional to the specific gravity and to the bending strength, 2) the hardness of wood measured in tangential direction to the annual ring increases along with the distance from the center of the annual ring to the peel, 3) the changes of specific gravity under 100 Mrad gamma irradiation are not remarkable, 4) the hardnesses of the soft woods are decreased more -readily than those of the hard woods, but the decreases of hardnesses are not extreme upto 10 Mrad sugges ting that the woods are sufficiently durable to gamma irradiation of below 10 Mard in the preparation of W. P. C.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.4
• /
• pp.420-427
• /
• 2014

The physical and mechanical properties of sawdust-rice husk mixed ceramic were investigated with rice husk mixing ratios. The mixed ceramic board was produced with carbonization and resin impregnated sawdust-rice husk board at high temperature. At the same percentage of resin impregnation condition, density and bending strength of the mixed ceramic board increased with increasing the mixing rates of rice husk, whereas weight loss of the ceramic boards decreased. At the same temperature condition for the carbonization of resin impregnated sawdust-rice husk board, the density and bending strength were the highest with 40% of rice husk mixing ratio.

• Korean Journal of Agricultural Science
• /
• v.37 no.2
• /
• pp.267-270
• /
• 2010

This study was carried out to manufacture black charcoal board from domestic wood waste by using serum protein adhesive which is natural, environment-friendly and human-friendly. For the preparation of the serum protein adhesive, pig blood from slaughterhouse was centrifuged and serum was separated from corpuscles and concentrated to 30% by dry weight basis. The particle size of charcoal from domestic wood waste for this study was #6-60. Hot pressing schedule was $170^{\circ}C$ and 40kgf/$cm^2$ (1 min)-10kgf/$cm^2$ (2.5 min)-40kgf/$cm^2$ (5 min). The black charcoal board made by the addition of 13% serum protein adhesive on dry weight basis gave 41.76kgf/$cm^2$ of bending strength, 8.12kgf/$cm^2$ of internal bonding strength, and excellent gas adsorption and workability.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.7-14
• /
• 1996

두께가 20mm와 30mm이고 폭이 40mm와 60mm 인 길이 600mm의 낙엽송 제재목에 응력파 시험과 휨강도 시험을 실시하였다. 모든 시험편은 생재 상태로 구입 후 함수율 약 13%로 조습 처리하여 응력파 시험과 휨강도 시험을 시행하였다. 휨 영계수와 휨강도는 두께가 큰 것이 작게 나타났다. 최상의 상관관계는 휨 영계수와 양 표면에서 구한 값의 평균값을 사용한 응력파 속도 및 영계수 사이에 나타났다. 휨 영계수와 관계에서 응력파 영계수는 응역파 속도 보다 더 확연한 옹이의 영향을 보였다.