• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.6
• /
• pp.41-50
• /
• 2011

This article is concerned with the technology to provide car driver the car's status which are composed of car trouble code in car engine and many sensors. In addition, it installs vehicle diagnostic programs on wireless communication's portable device, for example, Smart phone, PDA, PMP, UMPC. As a result, this is to provide car manager with many information of car sensors when we go to car maintenance. it can monitor relevant information on vehicle by portable device in real time, alert drivers with specific messages and also enable them to address abnormalities immediately. Moreover, the technology could help the drivers who perhaps don't know very well about their vehicles to drive safely and economically as well; the reason is because the whole system is composed of just Vehicle-information collecting device and personal wireless communication's portables and transfers the relating data to server computers through wireless network in order to handle information on vehicles. This technology make us monitor vehicle's running, failure and disorder by using wireless communication's portable device. Finally, this study system is composed of a lot of application to display us the car's status which get car's inner sensor information while driving a car.

• Journal of Korea Multimedia Society
• /
• v.15 no.10
• /
• pp.1236-1246
• /
• 2012

Autonomous mobile robot has ability to move itself so it can access to danger area or narrow place, and send acquired data by sensors at the same time. In order to drive to directed place, it should progress to the destination without any collision to other robot. In this study, we built and realized the collision avoidance system for autonomous mobile robot. By using antenna, IR and ultrasonic Sensors for collision avoidance, we made it possible to sense the attached and long-distance obstacle, and can avoid. Also, we used wired and wireless network to send the data after the mission.

• Journal of IKEEE
• /
• v.14 no.2
• /
• pp.58-63
• /
• 2010

In this paper, design and implementation of multi-modular robots of similar structure to the arthropods for rock path driving. Each module corresponds to an arthropod joint, which has an independent power supply and control equipment including drive and short-range Zigbee wireless communication that were implemented. On various directions and paths each module has the same driving direction and each module is controlled to operate or not by wireless communication. Depending on path condition, each module calculate the speed and torque and depending on the slope of a rough path, the number of active modules can be changed for the efficient driving on a variety of roads conditions. Experimental driving through rough road model, variable multi-module robot is implemented.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.52-56
• /
• 2014

In this paper, a high-efficiency power amplifier is implemented using a gate and drain bias control circuit for WPT (Wireless Power Transmission). This control circuit has been employed to improve the PAE (Power Added Efficiency). The gate and drain bias control circuits consists of a directional coupler, power detector, and operation amplifier. A high gain two-stage amplifier using a drive amplifier is used for the low input stage of the power amplifier. The proposed power amplifier that uses a gate and drain bias control circuit can have high efficiency at a low and high power level. The PAE has been improved up to 80.5%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.589-590
• /
• 2013

The fast development of electronic devices towards wireless, portable and multi-functionality desperately needs the self-powered and low maintenance power sources. The possibility to coupling the nanogenerator to wearable and portable electronic device facilitates the self powered device with independent and self sustained power source. Nanogenerator has ability to convert the low frequency mechanical vibration to electrical energy which is utilized to drive the electronic device [1]. The self powered power source has the ability to generate the power from environment and human activity has attracted much interest because of place and time independent. The human body motion based energy harvesting has created huge impact for future self powered electronics device applications. The power generated from the human body motion is enough to operate the future electronic devices. The energy harvesting from human body motion based on triboelectric effect has simple, cost-effective method [2, 3] and meet the required power density of devices. However, its output is still insufficient to driving electronic devices in continues manner so new technology and new device architecture required to meet required power. In the present work, we have fabricated the triboelectric nanogenerator using PDMS polymer. We have studied detail about the power output of the device with respect to different polymer thickness and varied separation distance.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2441-2446
• /
• 2018

This paper presents a radio frequency-to-direct current (RF-to-DC) converter for special RF power harvesting application at 915 MHz. The major featured components of the proposed RF-to-DC converter is the combination of a cross-coupled rectifier and an active diode: first, the cross-coupled rectifier boosts the input voltage to desired level, and an active diode blocks the reverse current, respectively. A prototype was implemented using $0.18{\mu}m$ CMOS technology, and the performance was proven from the fact that the targeted RF harvesting system's full-operation with higher power efficiency; even if the system's input power gets lower (e.g., from nominal 0 to min. -12 dBm), the proposed RF-to-DC converter constantly provides 1.47 V, which is exactly the voltage level to drive follow up system components like DC-to-DC converter and so on. And, maximum power conversion efficiency is 82 % calculated from the 0 dBm input power, 2.3 mA load current.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.7
• /
• pp.2246-2260
• /
• 2014

In this paper, a secure multilevel quadrature amplitude modulation (MQAM) scheme is proposed for the physical layer security (PLS) of the wireless communications. In the proposed scheme, each transmitted symbol's signal constellation (SC) is hopping with the control of two unique factors: amplitude distortion (AD) factor and phase hopping (PH) factor. With unknown the two factors, the eavesdropper cannot extract effective information from the received signal. We first introduce a security metric, referred to as secrecy gain, and drive a lower bound on the gain that the secrecy capacity can be improved. Then, we investigate the relationship among the secrecy gain, the signal to noise power ratios (SNRs) of the main and wiretap channels, and the secrecy capacity. Next, we analyze the security of the proposed scheme, and the results indicate that the secrecy capacity is improved by our scheme. Specifically, a positive secrecy capacity is always obtained, whether the quality of the main channel is better than that of the wiretap channel or not. Finally, the numerical results are provided to prove the analytical work, which further suggests the security of the proposed scheme.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.1
• /
• pp.73-79
• /
• 2014

In this study, the unmanned vehicle to develop a preliminary step, we were facilities for Automated Guided Vehicle (AGV) simulator is designed and implemented. Industry is increasingly the more advanced automation and management systems need to be efficient. These studies are at least 24-hour continuous unmanned vehicles and personnel can result in reduction of labor costs. In addition, safety accidents can be minimized in the industry as an effect of intelligent AGV is essential. This study is the initial step for the development of AGV. manufactured simulator to Simulation and drives the performance of the system is evaluated. The configuration of the simulator, ultrasonic sensors, infrared sensors, and using the obstacle were to follow a given path. In addition, two-way communication between the host computer and the main processor that was. communication method that IEE802.11 meets the standard is applied to high-speed wireless LAN systems, each of the sensor information is calculated. AGV having a drive shaft 4 of the four wheels are respectively independent structure. AGV's main processor is driven using a high-performance DSP, and the controller controls the steering device of the load could be significantly reduced.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.464-467
• /
• 2001

There nay be fierce debate over the nature of the medium that will herald the brave new world copper, fiber, wireless or satellite there is little doubt that future networks will be broadband in their capabilities. The Republic of Korea is a significant exception and leads the world, at present, in terms of number of subscribers with broadband access via ADSL. In order to further drive the growth in the broadband Internet access market, the government is scheduled to implement open access for ISPs and unbundling of the local loops of incumbent public telecom operators during the course of 2001. By the Way, Should incumbent telecommunication operators be obliged to provide unbundled access to the local loop\ulcorner

• Journal of Advanced Navigation Technology
• /
• v.8 no.2
• /
• pp.91-97
• /
• 2004

This paper presents the development of InGaAsP multiple quantum well asymmetric Fabry-Perot modulators(AFPM), which have a vertical structure and high performance and describes measurements of devices operating at 10GHz for next generation broadband wireless communication applications such as picocell systems. Advantages of the AFPM include low drive voltage, which is less than -2V, and -3dB coupling loss, good flatness of the frequency response and simple fiber alignment. A simple link demonstration has been introduced, resulting in 92dB/Hz spurious free dynamic range and 40dB inter-modulation distortion. This modulator could be use for broadband radio over fiber systems such as picocell and multiple RF links.