• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.559-562
• /
• 2017

In city, tracing of power transmission lines is difficult due to compound installation of overhead and underground lines, transposition, bad view caused by trees or big buildings. It is hard problem for electrical technician on site to trace power transformers or power lines to serve customers in 3 phase -4 wires power distribution systems. It is necessary that the correct and fast tracing method is required for load balancing among distribution lines. Old technology use to trace off-lines with high power impulse injection. Our proposed method use to trace live lines with very small power high frequency signal injection. Typical power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. Two end communication terminals are required to be synchronized between them for determination on electrically same phases. Challenging issue is to achieve synchronization without GPS providing synchronizing time. A novel power transformer and wire identification system is designed and implemented. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• Journal of Advanced Navigation Technology
• /
• v.9 no.1
• /
• pp.71-78
• /
• 2005

Nowadays, the demand of HPI(High-speed Portable Internet) has been gradually increased to support the various services of high speed wire line internet such as xDS. HPI can support high speed internet in anyplace, anytime. For successful development of HPI, the performance should be evaluated according to the cell size and/or the number of users and cell design should be carried out based on these criteria. The previous cellular systems using CDMA technique focus on the establishment of link based on power control but HPI systems consider the QoS (Quality of Service) and its performance based on the scheduling technique. The results from the system level simulation show that the throughput is sensitive to the cell size and the number of users has little impact on it. Moreover, the variation of service delay is more sensitive to the number of users but less to the cell size.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.6
• /
• pp.1096-1101
• /
• 2004

By a tremendous expansion of Internet users, there's a number effects that cause the phenomenon of bottlenecked switching packets from routers. In order to tear down this problem, distributed system is applicable to almost every highly performed router systems. The main processor of distributed system, which manages routing table, commands IPC to delivering the forwarding table line processor that eases functionalities of the router. This makes the system having wired-speed forwarding function based on the hardware so that the performance of the network can be enhanced. Therefore, IPC, which assign a part of router, is necessary to exchange data smoothly and the constitution of IPC using Ethernet is widely adapted as a method for saving investment. In this paper, R-IPC mechanism improve the packet-processing rate over 10% through changed from defect of conventional Ethernet IPC, that is, 2 layer processing to TCP/IP or UDP/ IP into 1 layer processing for efficient packet forwarding.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.18 no.4
• /
• pp.79-91
• /
• 2008

Modern society as an information society, a lot of information is communicated in on-line. Specially, mobile environment based on radio communication has a characteristic of flexibility compared with wire communication and is developed rapidly. However, the more mobile technology is developed the more security for sensitive information is needed. Therefore, MTM(Mobile Trusted Module) is developed and promoted by TCG(Trusted Computing Group), which is an industry standard body to enhance the security level in the mobile computing environment. MTM, hardware security module for mobile environment, offers user's privacy protection, platform integrity verification, and individual platform attestation. On the other hand, secure migration scheme is required in case secret data or key is transferred from one platform to the other platform. In this paper, we analyze migration schemes which were described in TCG standard and other papers and then propose security maintenance scheme for secret data using USIM(Universal Subscriber Identity Module).

• Journal of the Korean Society for Railway
• /
• v.19 no.6
• /
• pp.736-743
• /
• 2016

In accordance with the trend of higher speed and automation, the Train Control System is building on the technology of control methods using radio in the technology of exchanging information by wire, toward a wireless communication method that will be applied using LTE-R radio communication technology with $4^{th}$ generation LTE mobile communication a $2^{nd}$ generation GSM-R. Therefore, a standard specification suitable for the Korea Radio based Train Control System-2(below KRTCS-2) for the 350km/h class using wireless communication is created; a prototype based on the standard specification is installed on a high-speed train and is installed on a test section(Ik san-Jeong eup) on the Honam high speed line to ensure the reliability and safety of the standard specifications, which are verified through various performance tests. In the future, the standard specification that has been established as a national railway standard, and the standard specifications will be commercialized by applying the train control system to conventional and High speed railway lines.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.778-784
• /
• 2017

In this paper, we propose wired and wireless distributed control systems designed to improve the freight logistics efficiency and verify wired distributed control systems. The verification condition required that 50 cargo vehicles be connected and operated to travel 21 km from Busan Sinhang station to Jinlye Station at an average speed of about 100km/h. The verification results show that the traction output and braking output of the control and controlled cars are dispersed by the wired distributed control system. The application is expected to more than double the efficiency of the logistics compared to the existing freight transportation system. However, in the case of the wired distributed control system, cable installation and maintenance are difficult, and it is impossible to change the combination of freight vehicles. Through the verification of the wired distributed control system, the applicability of distributed control systems to freight vehicles in Korea was confirmed and the system was further developed to produce a wireless distributed control system. In order to apply the wireless distributed control system, a propagation environment analysis for the ISM band was performed in the testbed and, as a result, it was confirmed that Wifi technology using the ISM band could be utilized. In order to use the WDP (Wireless Distributed Power) devices newly installed in the target vehicles, the transmission / reception control signals associated with the propulsion / braking / total control devices are defined. In the case of wireless distributed control systems, the convenience of their application and operation is guaranteed, but reliability and emergency safety measures should because of the dependence of the control of the vehicle on radio signals.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1519-1525
• /
• 2006

This paper proposes the U-healtcare middleware that is based on mininumCORBA. Ubiquitous healthcare system is generated by combining the technologies of computer system and medical system. This makes available that the person can receive medical treatment anywhere, anytime at on-line. The Healthcare devices are connected to network system as wire or wireless internet. So, the computer system can gather the vital information from the person at the real time and transfers the information to the server system that processes the medical information. When a medical doctor makes a diagnosis they can get more information about the patient by using the information within the server. Users would like to receive more services in the ubiquitous healthcare system than the traditional medical system. And in U-healthcare system, every healthcare devices and the users have to be connected to network system and the information from them has to be integrated. U-Home Healthcare middleware I proposed in this paper will do everything that I mentioned above.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.4
• /
• pp.61-71
• /
• 1999

The recent trend toward higher frequencies, miniaturization and lower-cost in wireless communication equipment is demanding high density packaging technologies such flip chip interconnection and multichip module(MCM) as a substitute of conventional plastic package. With analyzing the recently reported research results of the RF flip chip, this paper presents the technical issues and advantages of RF flip chip and suggest the flip chip technologies suitable for the development stage. At first, most of RF flip chips are designed in a coplanar waveguide line instead of microstrip in order to achieve better electrical performance and to avoid the interaction with a substrate. Secondly, eliminating wafer back-side grinding, via formation, and back-side metallization enables the manufacturing cost to be reduced. Finally, the electrical performance of flip chip bonding is much better than that of plastic package and the flip chip interconnection is more suitable for Transmit/Receiver modules at higher frequency. However, the characterization of CPW designed RF flip chip must be thoroughly studied and the Au stud bump bonding shall be suggested at the earlier stage of RF flip chip development.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.8
• /
• pp.1709-1715
• /
• 2005

This paper describes the development of 3-D web graphic library for dynamic web graphic design. The 3-D web graphic library developed in this per supports creation of 3-D objects like cube and sphere objects, elimination of hidden line and surface, and the shading of diffuse and specular reflections. It provides, in drawing, perspective projection of an object depth first sort of multiple objects, and wire frame and solid models. It also supports texture mapping function for realistic and dynamic web application in application software. Each created 3-D object gives functions for the scaling, translation, and rotation of itself. It can be used for the development of dynamic web application software and the advertisement of information for business and tourism as a 3-D web graphic library engine. It is written in 'Java' language and runs on web browsers with Java virtual machine without any dependancy of client computer system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.2
• /
• pp.391-400
• /
• 2008

There has been increasing interest in developing Structure Health Monitoring(SHM) system based on wireless sensor network(WSN) due to recent advancement in sensor network technologies. SHM is the continuous monitoring of the condition such a acceleration or load of a structure. The SHM system works, which measure key structure parameters systematically, provide information in evaluation of structure integrity, durability and reliability. Currently SHM system collects data via analog sensor and then sends to analysis application through the wired network. The wire system support high accuracy, but suffers the disadvantages in installation costs, complexity of connection and loss of line. It's also difficult to add new sensor nodes. We design and implement the SHM system based on WSN technology to solve those problems.