• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.162-169
• /
• 2006

Steel cord which is used as reinforcement in car tires is produced by wet-drawing process. Recently the quality improvement of the steel cord product is demanded by the tire market. After cold drawing process, produced residual stresses have a harmful effect on the durability of the wire and become the cause which decreases the quality of the product. Therefore, to improve the quality of the steel cord product, the research regarding the method of residual stress relaxation is necessary. To evaluate the quality of the cold drawn wire, it is very important to measure the residual stress, because the residual stress decides a variety of the quality level which is demanded in the cold drawn wire. The aim of this study is to propose residual stress relaxation method in the drawn wire using FE-analysis. The validity of the analysis results was verified by Nano indentation test.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.89-92
• /
• 2004

This paper is concerned with the drawing process of Al-Si wire. In this study, the finite-element model established in previous work was used to analyze the effects of various forming parameters, which included the reduction in area, the semi-die angle, the aspect ratio and the inter-particle spacing of the Si in drawing processes. The finite-element results gave the consolidation condition. From the results of analysis, the effects of each forming parameter were determined. It is possible to obtain the important basic data which can be guaranteed in the fracture prevention of Al-Si wire by using FEM simulation.

• Transactions of Materials Processing
• /
• v.16 no.6
• /
• pp.463-466
• /
• 2007

Micro-wire made from straightening process invents high added value and it has been adopted many industrial fields. Therefore, many research activities about straightening process are advanced actively. It is known that fine straightness of micro-wire can be obtained by removing residual stress induced during the manufacturing processes. Generally, residual stress is removed or minimized through several drawing processes with heat treatment. In this study, the residual stress at each straightening process is calculated and monitored by finite element analyses and the main reason of stress change is investigated.

• Korean Journal of Materials Research
• /
• v.27 no.11
• /
• pp.597-602
• /
• 2017

In this study, an Al-0.7wt%Fe-0.2wt%Mg-0.2wt%Cu-0.02wt%B alloy was designed to fabricate an aluminum alloy for electrical wire having both high strength and high conductivity. The designed Al alloy was processed by casting, extrusion and drawing processes. Especially, the drawing process was done by severe deformation of a rod with an initial diameter of 12 mm into a wire of 2 mm diameter; process was equivalent to an effective strain of 3.58, and the total reduction in area was 97 %. The drawn Al alloy wire was then annealed at various temperatures of 200 to $400^{\circ}C$ for 30 minutes. The mechanical properties, microstructural changes and electrical properties of the annealed specimens were investigated. As the annealing temperature increased, the tensile strength decreased and the elongation increased. Recovery or/and recrystallization occurred as annealing temperature increased, and complete recrystallization occurred at annealing temperatures over $300^{\circ}C$. Electric conductivity increased with increasing temperature up to $250^{\circ}C$, but no significant change was observed above $300^{\circ}C$. It is concluded that, from the viewpoint of the mechanical and electrical properties, the specimen annealed at $350^{\circ}C$ is the most suitable for the wire drawn Al alloy electrical wire.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.55-58
• /
• 2002

PIT method which is used at fabricating Bi-2223/Ag HTS wire includes a drawing process, conventional deformation method. Drawing of meta1(Ag) and ceramic (BiSrCaCuO) composite is also difficult and significant for uniform deformation. In this paper, parameters of uniform deformation was studied at Bi-2223/ Ag multifilamentary HTS wire. Powder and rod as a starting precursor was compared at 55 filament and 54 filament Bi-2223/Ag HTS wire, respectively. Micro-hardness and area COV of the filaments was also evaluated when the diameters were decreased through drawing operations.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.308-314
• /
• 2020

A commercial AA1070 alloy for electrical wire is severely deformed by drawing process in which a rod with an initial diameter of 9mm into is reduced to a wire of 2mm diameter. The drawn AA1070 wire is then annealed at various temperatures from 200 to 450 ℃ for 2h. Changes in microstructure, mechanical properties and electrical properties of the specimens with annealing temperature are investigated in detail. The specimen begins partially to recrystallize at 250 ℃; above 300 ℃ it is covered with equiaxed recrystallized grains over all regions. Fiber textures of {110}<111> and {112}<111> components are mainly developed, and {110}<001> texture is partially developed as well. The tensile strength tends to decrease with annealing temperature due to the occurrence of recovery or/and recrystallization. On the other hand, the elongation of the annealed wire increases with the annealing temperature, and reaches a maximum value of 33.3 % at 300 ℃. Electric conductivity of the specimens increases with annealing temperature, and reaches a maximum value of 62.6 %IACS after annealing at 450 ℃. These results are discussed in comparison with those for the other aluminum alloy.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.250-253
• /
• 2007

It is known that fine straightness of micro-wire can be obtained by removing residual stress induced during the manufacturing processes. Generally, residual stress is removed or minimized through several drawing processes with heat treatment. In this study, the residual stress at each straightening process is calculated and monitored by finite element analyses and the main reason of stress change is investigated.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.2
• /
• pp.77-81
• /
• 2017

CP (Commercially Pure) titanium has been widely used in various industries such as in energy plants and bio-materials because of an excellent corrosion resistance and its non-toxicity to the human body. But there are limitations for usage as structural materials due to low strength. The tensile properties of CP titanium could be improved by microstructure refinement such as in a SPD (Severe Plastic Deformation) process. However, high strengthening of CP titanium wire is impossible by SPD processes like ECAP (Equal Channel Angular Pressing), HPT (High-Pressure Torsion), and the ARB (Accumulative Roll Bonding) process. The study purposes are to increase the strength of CP titanium wire by optimization of the cold drawing process and the harmonization with mechanical properties by heat treatments for the next forming process. The optimization process was investigated with regard to the design of drawing dies and the reduction ratio of cross sections. The elongations of high strength CP titanium were controlled by heat treatment.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.85-87
• /
• 2003

Intermediate annealing was carried out during wire drawing for uniform deformation of 500 m class Bi-2223/Ag HTS tapes. Wire drawing force was measured to evaluate the uniformity of wire deformation along the length. To prevent sausage and filament breakage of wire, drawing stress was controlled below 200 MPa by using intermediate annealing process. Thickness and width of the rolled tapes was measured 0.23 mm and 4.1 mm with low deviation $\pm$ 0.08 mm and $\pm$ 0.09 mm, respectively. The critical current of the 500 m tapes was measured 33.7 A $\pm$ 3.7 A by continuous critical current measurement system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1410-1413
• /
• 2003

Drawing is a basic plastic deformation method and productive manufacturing process make wire. rod and variety section geometry bar. Study for the rod drawing process of rod was researched long littles. but non-axisymmetric drawing process is weak. So metal flow is very irregular in non-axisymmetric drawing process and difficult to define about material deformation generally. In this paper, to solve material deformation, use finite element method and then define suitable shape for rod to hexagonal drawing dies. And research corner filling rate and surface roughness for the high strength steel hexagonal bar produced defined dies.