• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.2
• /
• pp.69-73
• /
• 2002

The effect of the numbers of processing on the punch and surface roughness of die block in the W-EDM, which is frequently used to manufacture parts of press die is studied. W-EDM equipment (Sodic A500H), the application of which has increased for its precision, is used in the process three times. To inspect the roughness of the three-time-processed dimension of the punch and the die, the surface roughness measuring instrument (System 5000 of Federal) is used.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.4
• /
• pp.545-549
• /
• 2006

W-EDM is generally used to manufacture punches and die plates from among press mold parts. Before W-EDM was used, however, punches and die plates manufactured via mechanical processing were used to manufacture products, with the die life of the mold expiring after 2,000,000~2,300,000 products have been manufactured. When the mold manufactured through W-EDM was used, however, its service life expired only after 700,000~800,000 products have been manufactured. Since this was attributed to the deformed layer formed after using W-EDM, the surfaces before and after W-EDM was used were scanned using SEM to verify the occurrence of such layer. This study sought to come up with a method of eliminating such phenomenon.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.956-959
• /
• 2001

In die and mould industry, major material such as cemented carbide is broadly used for increasing the life time and decreasing the cost. It is also required the development for the skills of wire-cut electrical discharge machining(WEDM), but the WEDMed surface was found to be worst due to the attached components of wire. Precision machining method like lapping is necessary for obtaining high quality surface. The lapping compound such as Al2O3 and SiC and cast iron lap can be used for lapping process. The components of Cu and Zn were found WEDMed surface of the specimen. As the result, the low quality of precision was obtained and the heat damage layer of the specimen was occurred. The value of surface hardness was deteriorated, and therefore finish process was required.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.69-69
• /
• 2003

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.1
• /
• pp.25-29
• /
• 2005

Titanium specially has high specific strength, excellent mechanical properties as fatigue strength and fracture ductility, good corrosion resistance, and therefore are broadly applied to the various fields. It is required the developmennt for the skills of wire-cut electrical discharge machining(WEDM), but the WEDMed surface was found to be worst due to the attached components of wire. Therefore precision maching method like lapping is necessary for getting high quilty surface. Roughness of lapped surface, surface hardness to each process depth and improved method of surface shape were stuided experimentally, by changing of grain size of diamond lap material and lapping pressure with constant speed in lapping process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.322-328
• /
• 2002

In wire-electrical discharge machining (W-EDM), the dielectric plays an important role as the working fluid. It affects the material removal rate and the properties of the machined surface. This paper deals with the effects of the electrical conductivity of dielectric and cobalt percentage of sintered carbides on the machining characteristics and the machined surface integrities with deionized water as dielectric. A series of experiments have been performed on sintered carbides having different cobalt contents. Experimental results show that a higher cobalt content of WC decreases the metal removal rate and worsens the surface quality. Lower electrical conductivity of the dielectric results in a higher metal removal rate as the gap between wire electrode and workpiece reduced. Especially, the surface integrities of rough-cut workpiece, wire electrode, and debris were analyzed also through scanning electron microscopy(SEM) and surface roughness tester. By energy dispersive spectrometry(EDS), it is confirmed that micro cracks and some of electrode material are found on the workpiece surface.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.215-216
• /
• 2002

This paper describes the wear characteristics of WC-Co cemented carbides machined with Wire-cut or Die-sinking EOM. We prepared the specimens with different grades of grinding to remove the affected layer after the EDM. These specimens were experimented by block-on-cylinder type tribometer. The result indicated that although the hardness of the affected layer was lower than that of the bulk, wear resistance was increased. In order to investigate the cause of the increase in wear resistance of the affected layer, the layer was observed and analyzed by SEM and ESCA. We also discussed the mean free path of Co phase.

• Proceedings of the KAIS Fall Conference
• /
• 2002.05a
• /
• pp.59-64
• /
• 2002

The effect of the numbers of processing on the punch and surface roughness of die block in the W-EDM, which is frequently used to manufacture parts of press die is studied. W-EDM equipment(Sodic A500H), the application of which has increased for its precision, is used in the process three times. To inspect the roughness of the three-time-processed dimension of the punch and the die, the surface roughness measuring instrument(System 5000 of Federal) is used.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.3
• /
• pp.17-23
• /
• 2004

The performance and life of a die are influenced by the machining methods. In order to examine the effects of machining methods on surface charactenstics, simple experiments are devised and performed. A die steel STD11, commonly used as a die material in press working, is selected. Three ways of machining methods to manufacture a die are considered. Those are (1) milling and then grinding, (2) wire-cut electric discharge dachining (W-EDM) and (3) heat treatment after W-EDM. The resulting surface roughnesses are measured. Also, the changes of surface microstructures are investigated using the scanning electron microscope(SEM) with energy dispersive X-ray spectrometer(EDS) and the results are discussed in details.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.739-742
• /
• 2000

From the experimental study of W-EDM for alloyed steel, the characteristics such as Hand Drum Form and surface roughness have been observed and evaluated for various conditions. In square hole, the increase of If as to made condition the calculate high value of surface roughness. Also compare dimensionless square hole with circle hole' graph. In circle hole, if a value of surface roughness IP 6 in a side of circle it show a 0.4${\mu}{\textrm}{m}$ and in IP 8, 0.6${\mu}{\textrm}{m}$, in IP 10, 0.7${\mu}{\textrm}{m}$, in IP 12. 0.8${\mu}{\textrm}{m}$ higher than before. This figure show the surface roughness is higher than before, because a table move in either X-axis or Y-axis in square hole, on the contrary, in circle there table move in X-axis and Y-axis at the same time. hand drum form getting small when wire tension increase 1000gf to 1500gf, at the same working conditions. the smaller of off time, the mailer of hand drum form in same condition and same wire tension. but if you compare square hole with circle hole' graph hand drum form displayed in maintained term of working condision, on the contrary, in case of square hole variation of hand drum form is more increase than a grow of IP