• 대한화학회지
• /
• 제54권2호
• /
• pp.198-207
• /
• 2010

독스핀 하이드로클로라이드 선택전극의 구조와 성능특징에 대하여 개발하였다. 전극의 3가지 형태가 있다. I. 플라스틱 막 II. 코팅된 선형 III. 흑연으로 된 로드, 이것들은 암모늄 라이네케이트를 갖는 독스핀 하이드로클로라이드의 결합에 기초하여 구성되었다. 막의 조성, 가소제의 종류, 시험용액의 pH, 담궈 놓은 시간 그리고 전극에 있는 이질 이온들의 영향을 조사했다. $25^{\circ}C$에서 전극 I, II, III에 대해 각각 57.41 ${\pm}$ 0.5, 56.22 ${\pm}$ 0.2 and 52.88 ${\pm}$ 0.7 mV 의 평균 보정 그래프 기울기를 갖는 Nernst 반응을 보여준다. 그리고 전극 I, II, III에 대해 $1{\times}10^{-2}-1{\times}10^{-6}M$, $5{\times}10^{-2}-1{\times}10^{-6}M$ 그리고 $1{\times}10^{-3}-5{\times}10^{-6}M$의 독스핀 하이드로클로라이드 농도범위에 있고, $5.0{\times}10^{-7}M$, $6.3{\time}10^{-7}M$ 그리고 $2.5{\times}10^{-6}M$의 검출한계를 갖는다는 것을 보여준다. 만들어진 전극은 pH 3 - 7의 범위에서 선택적으로 정밀하고, 사용 가능한 평균을 보였다. 공통양이온, 알칼로이드, 설탕 아미노산, 그리고 약품첨가제로부터의 방해가 기록되었다. 제안된 전극에 의해 얻어진 결과는 약의 조세와 생물학적 유체에 있어서 약물의 확인에 성공적으로 적용되었다.

• Nuclear Engineering and Technology
• /
• 제45권6호
• /
• pp.721-730
• /
• 2013

Within the framework of the ASTRID project, core design studies are being conducted by the CEA with support from AREVA and EDF. The pre-conceptual design studies are being conducted in accordance with the GEN IV reactor objectives, particularly in terms of improving safety. This involves limiting the consequences of 1) a hypothetical control rod withdrawal accident (by minimizing the core reactivity loss during the irradiation cycle), and 2) an hypothetical loss-of-flow accident (by reducing the sodium void worth). Two types of cores are being studied for the ASTRID project. The first is based on a 'large pin/small spacing wire' concept derived from the SFR V2b, while the other is based on an innovative CFV design. A distinctive feature of the CFV core is its negative sodium void worth. In 2011, the evaluation of a preliminary version (v1) of this CFV core for ASTRID underlined its potential capacity to improve the prevention of severe accidents. An improved version of the ASTRID CFV core (v2) was proposed in 2012 to comply with all the control rod withdrawal criteria, while increasing safety margins for all unprotected-loss-of-flow (ULOF) transients and improving the general design. This paper describes the CFV v2 design options and reports on the progress of the studies at the end of pre-conceptual design phase 1 concerning: - Core performance, - Intrinsic behavior during unprotected transients, - Simulation of severe accident scenarios, - Qualification requirements. The paper also specifies the open options for the materials, sub-assemblies, absorbers, and core monitoring that will continue to be studied during the conceptual design phase.

• 한국산업융합학회 논문집
• /
• 제14권2호
• /
• pp.59-65
• /
• 2011

$CO_2$ Welding which uses $CO_2$ instead of inert gas is most widely used in industrial sites. Welding rod for $CO_2$ Welding is roughly divided into solid wire and flux cored wire. $CO_2$ Welding has higher efficiency than any other welding methods, and also economic and speedy to handle, that's why is used frequently for welding general structures. As most of studies about $CO_2$ Welding are focused on metallurgical changes of successful joints, they developed theories about the change of configuration on weld parts. This study is especially focused on not only the change of configuration on weld parts, but also the change of the penetrating depth through changing the position of welding torch. For inspection, applied AWS A5.20 E70-1 among welding wires and fixed moving angles of torch, but controled the values of voltage and the position of welding. Also Automatic Feed Mechanism is used for exact movement of material, specimen is a piece of steel for general structures. By measuring and analyzing the configuration of sliced section and the values of welding leg length and welding throat after welding, the outcome about the changes turned out.

• Nuclear Engineering and Technology
• /
• 제52권5호
• /
• pp.897-907
• /
• 2020

The flow characteristics of reactor fuel assembly always intrigue the designers and the experimentalists among the myriad phenomena that occur simultaneously in a nuclear core. In this work, the visual experimental method has been developed on the basis of refraction index matching (RIM) and particle image velocimetry (PIV) techniques to investigate the detailed flow characteristics in China fast reactor fuel subassembly. A 7-rod bundle of simulated fuel subassembly was fabricated for fine examination of flow characteristics in different subchannels. The experiments were performed at condition of Re=6500 (axial bulk velocity 1.6 m/s) and the fluid medium was maintained at 30℃ and 1.0 bar during operation. As for results, axial and lateral flow features were observed. It is shown that the spiral wire has an inhibitory effect on axial flow and significant intensity of lateral flow mixing effect is induced by the wire. The root mean square (RMS) of lateral velocity fluctuation was acquired after data processing, which indicates the strong turbulence characteristics in different flow subchannels.

• 한국전기전자재료학회논문지
• /
• 제28권5호
• /
• pp.338-343
• /
• 2015

Dye sensitized solar cells (DSSCs), which is one of the contending renewable energy sources, have the problem of low efficiency. To improve the efficiency, the fast electron transport and long electron lifetime are required. In this study, one-dimensional sodium hexatitanate, which is expected to have an advantageous structure for electron transports, was synthesized and the feasibility of the material on DSSC was tested. Its physical properties were characterized by the SEM, XRD, and BET method. The dye adsorption and solar cell properties were also characterized. In addition to the expectation of fast electron transport, sodium hexatitanate showed longer electron lifetime: This means sodium hexatitanate can improve the DSSC efficiency. However, it showed low current and voltage because of the low surface area leading to the low amount of dye adsorbed. Therefore, it should be mixed with titanium oxide with high surface area for the optimal performance.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.247-252
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, two kinds of spring steel (SUP7, 50CrV4) are used. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from on low stress condition, the 1st stage shot peening is not affected by nonmetallic inclusion under metal. it is possible that the 2nd stage shot peening increases the fatigue life and the high stress but that is affected by nonmetallic inclusion under metal. so far beeasily 50CrV4 have made high stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.145-150
• /
• 2000

Micro punching is one of general methods to fabricate simple holes such as permanent ink-jet printer nozzles. A thin punch, that is need for micro punching, usually has been obtained by mechanical machining. There are some method to obtain a thin punch from a cylindrical rod, e.g., microgrinding and WEDG (Wire Electro-Discharge Grinding). Inefficiently, only one punch can be obtained from these machining methods. In contrast with these methods, many punches can be fabricated simultaneously by electrochemical process. Electrochemical process has usually aimed to obtain very sharp probe for atomic force microscopy (AFM) or scanning tunneling microscopy (STM), and it has not been considered the whole shape of a probe in spite of good merits. In this paper, an ultrathin punch with a tapered shape and a cylindrical tip is newly fabricated by electrochemical process.

• 한국유체기계학회 논문집
• /
• 제17권6호
• /
• pp.89-94
• /
• 2014

The 4th generation SFR is being designed with a milestone of construction by 2028. It is important to understand the subchannel flow characteristics in fuel assembly through the experimental investigations and to estimate the calculation uncertainties for insuring the confidence of the design code calculation results. The friction coefficient and the mixing coefficient are selected as primary parameters. The two parameters are related to the flow distribution and diffusion. To identify the flow distribution, an iso-kinetic method was developed based on the previous study. For the mixing parameters, a wire mesh system and a laser induced fluorescence methods were developed in parallel. The measuring systems were adopted on 37 rod bundle test geometry, which was developed based on the Euler number scaling. A scaling method for a design of experimental facility and the experimental identification techniques for the flow distribution and mixing parameters were developed based on the measurement requirement.

• 한국주조공학회지
• /
• 제26권4호
• /
• pp.180-183
• /
• 2006

NICI재의 미세조직 및 기계적 성질에 미치는 Ni 첨가원소의 영향을 연구하였다. 선재공장의 열간압연롤재로서의 NICI재는 내열 피로크랙성, 경도값, 인장성질, 내마모성이 매우 중요하다. 주방상태에서 4% Ni 첨가로 주요 기지상인 퍼얼라이트상이 베이나이트상으로 변화되었다. 베이나이트상을 주요 기지상으로 가지는 4% Ni 첨가 NICl재는 퍼얼라이트상을 주요 기지상으로 가지는 통상의 NICI재에 비해서 경도값(HRC 48) 및 인장강도값($72\;kg/mm^2$)이 우수하였으며, 이는 선재압연롤 재료로서 우수한 성능을 발휘할 수 있을 것으로 예측된다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 춘계학술대회 논문집
• /
• pp.338-343
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc., In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, two kinds of spring steel(SAE 9254, DIN 50CrV4) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) on low stress condition, the single stage shot peening is not affected by nonmetallic inclusion under metal. (2) it is possible that the two-stage shot peening increases the fatigue life and the high stress, but, that is affected by nonmetallic inclusion under metal. (3) so far, beeasily 50CrV4 have made high stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.