A miniaturized wind-mill type ultrasonic motor which has diameter in 12.7 mm and thickness in 2.0mm using PMN-PZT piezoelectric ceramics was fabricated. The wind-mill type ultrasonic motors has only three plate and of two wind-mill shape slotted metal endcaps a rotor whose end is hollowed out so that its periphery fits with the shape of the stator and a bearing to guide the rotor. A Finite Element Analysis was carried out to obtain the endcaps behavior under a radial displacement change of piezoelectric disk and to optimize the structure of the number of slots. Increasing the applied voltage the revolution speed of ultrasonic motors was increased. The maximum speed of 700 rpm and the maximum torque of 0.22 nN·m of the wind-mill type ultrasonic motors were obtained.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2000.07a
/
pp.373-376
/
2000
The modified Moonie(Cymbal) transducer has been investigated for an accelerometer application. This paper present a wind-mill type ultrasonic motors using ternary piezoelectric ceramics and aluminum endcaps applied by cymbal transducer. The maximum displacement was increased depend on applied voltage and layer number. The multi-layer was fabricated by tape casting using doctor-blade process. The maximum displacement of multi-layered ultrasonic motor was much higher than that of one-layered.
The purpose of this study was to investigate the effects of silicon and nickel additions that influenced the impact and tensile properties of heavy section as-cast ductile irons for wind mill. Based on the results of the metallographic analysis and the mechanical testing on the 2.0 wt.%Si (LS group) and 2.4 wt.%Si (HS group) ductile irons, which contains 0.0, 0.3, 0.6 and 0.9 wt.%Ni, respectively, the following conclusions could be obtained. The nickel additions increased the tensile properties, the microhardness of pearlite, and the pearlite fraction of matrix for the specimen with the same silicon content. The mechanical properties of LS group specimen were in the range of the specification for the ductile iron wind mill castings. The LS group specimens showed higher absorbed impact energy at room temperature and $-20^{\circ}C$ than that of the HS group specimens. However, the absorbed impact energy at $-20^{\circ}C$ for the HS group specimens was observed to be sharply decreased under 10 J by addition of the nickel.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2000.11a
/
pp.181-183
/
2000
Ultrasonic Motors of Wind-Mill type(diameter in 11.35mm, thickness in 2.8mm, and 1.44g weight) using Piezoelectric Ceramics have been developed. In recent study, Maximum torque in 100$V_{max}$, 105.8kHz was 7.2 ${\mu}$N$.$m, and bidirectional revolution using single-phase AC was presented. However, it is difficult to use because of small torque. Thus, in present study, new type of Wind -Mill Type Ultrasonic Motor of was designed as stator' structure was changed
분쇄도구는 점차수차, 풍차 그리고 증기기관이란 동력기술과 맞물려 제분공정이 대규모화되어 지배자는 이를 독점, 집중화시켜 마침내 공장제도의 원형이 이루어졌던 것이다. 여기서 우리는 wind mill, water mill, rolling mill, miller, milling M/C 등 단어가 뜻하듯 단순히 "제분하는 기계" 뿐만 아니라 "자연력으로 구동되는 기계설비를 사용하였던 모든 Manufacture"라는 것을 공통어 밀(mill)에서 엿볼 수가 있다. James Watt의 증기기관이 실용 중에도 한동안 수차는 산 업 여러 분야에서 동력원으로 자리를 지켜 왔지만 현재는 획기적으로 성능이 좋은 Francis, Pelton, 및 Ossberger 수차가 상업발전소에서 쉬지 않고 돌아가고 있다. 통차, 동미차, 번차, 수대, 연애, 파쇄 등 전통적인 수차와 석구가 기본이 되어 분명히 근세 생산기계설비를 발명케 하였고 동력원으로서 화려한 전성기를 누렸다. 지금은 역사속에 잊혀져 가지만 우리는 시골 산간에서 돌아가는 물레방아의 수연한 고태를 볼 때면 민속문화학, 그리고 기술사적 측면에서 문화재로서의 명맥을 기려 잘 보존할 의무가 절실하다고 생각한다. 보존할 의무가 절실하다고 생각한다.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
1998.11a
/
pp.231-234
/
1998
In this study, the wind-mill type ultrasonic motor was fabricated, and then resonant frequency and vibration velocity characteristics of the stator were measured. Brass metal was pressed with umbrella-type using metal mold, then slot of 4 kind was processed in each of thickness. Among sixteen's stators, resonant frequency on vibration velocity was decreased remarkably in stator of higher resonant point, but resonant frequency on vibration velocity wasn't almost changed at lower resonant point of stator. The thickener thickness of elastic body, vibration velocity was decreased. The more slot of elastic body, vibration velocity was increased Applied voltage was changed from 10$V_{max}$ to 100$V_{max}$. Maximum vibration velocity value was 2.0[m/s].
A well designed hybrid power system (HPS) can deliver electrical energy in a cost effective way. In this paper, model for HPS consisting of photo voltaic (PV) module and wind mill as renewable energy sources (RES) and solar lead acid battery as storage device connected to unidirectional grid is developed for peak demand reduction. Life time energy cost of the system is evaluated. One year hourly site condition and load pattern are taken into account for analysing the HPS. The optimal HPS is determined for least life time energy cost subject to the constraints like state of charge of the battery bank, dump load, renewable energy (RE) generation etc. Optimal solutions are also found out individually for PV module and wind mill. These three systems are compared to find out the most feasible combination. The results show that the HPS can deliver energy in an acceptable cost with reduced peak consumption from the grid. The proposed optimization algorithm is suitable for determining optimal HPS for desired location and load with least energy cost.
The efficient refinement of seed is required to reduce the cost and labor input in artificial propagation of wild plant. This study was carried out to develop methods for collecting and refining tiny seeds from wild plants. For obtaining Phragmites communis seeds, the inflorescence was cut into small fragments using a Straw Cutter and subsequently detached pappus hairs from seed coat by Hammer Mill. The primary refined seeds were passed 1.0 mm sieve. The screened seeds were subjected to Seed Blower with wind speed of 0.25 mㆍsec-1 to collected intact and well-ripen seeds. The seeds of Imperata cylindrica were refined as follows. Inflorescences were cut using a Straw Cutter first. The pappus was removed from cut fragments using a Hammer Mill and subsequently subjected to Seed Scarifier at 500rpm for 60 sec. for further separation. The separated seeds were passed 1.0 mm screen and collected after blowing with Seed Blower of wind speed of 0.15 mㆍsec-1. When the amount of seed was too little to refine with Seed Scarifier and Blower, the procedure was slightly modified from the procedure described above. The crude seed mixture obtained from Hammer Mill step was hand-refined roughly and then immersed into cone. (95%) sulfuric acid for 2 min. and collected floating portion after dilution of sulfuric acid solution 100 times with tap water. The collected seeds were dried and passed 0.149 mm sieve. During seed refining process using mechanical or sulfuric acid treatments, a small portion of damaged seed were evolved, however, the amount was not noticeable as compared to the total amount of collected seeds. Because the germination percentages between hand-refined seeds and seeds refined by above methods were not statistically different, the developed procedures for refining tiny seed of wild plants are helpful to reduce the cost and labor input in artificial propagation of two species.
The world is gradually running short of fossil fuel. Currently, the role of wind turbine is attracting great attention from all over the world. The objective of this study is to investigate blades of Vertical-axial wind turbine (VAWT) for optimum design using the CFD from the aerodynamics point of view. Because one of the performance of wind turbine depends on shape of blades, the study of comparing one gyro mill type blade and a modified one was carried out. Using the results of computation, we calculated and compared RPM for both models at same wind velocity. And we calculated angular acceleration and moment of inertia to find torque in every time-step. And the pressure contour and velocity profile around the blade were analyzed Also, this study is performed to calculate the wake effect.
Kim, Young-Jung;Ryou, Young-Sun;Kang, Geum-Choon;Paek, Yee;Yun, Jin-Ha;Kang, Youn-Ku
Agricultural and Biosystems Engineering
/
v.6
no.2
/
pp.65-69
/
2005
A windheat generation system with a Savonius windturbine was developed and the performance was evaluated through field tests. The system consisted of a heat generation drum, heat exchanger, water storage tank, and two circulation pumps. Frictional heat is created by rotation of a rotor inside the drum containing thermo oil, and was used to heat water. In order to estimate the capacity of this windheat generation system, weather data was collected for one year at the site near the windheat generation system. Wind Power from the savonius wind turbine mill was transmitted to the heat generation system with an one-to-three gear system. Starting force to rotate the savonius wind turbine and the whole system including the windheat generation system were 1.0 and 2.5 kg, respectively. Under the outdoor wind condition, maximum speed of the rotor in the drum was 75rpm at wind speed 6.5 m/sec, which was not fast enough to produce heat for greenhouse heating. Annual cumulative hours for wind speeds greater than 5 m/sec at height of 10, 20, 30 m were 190, 300 and 1020 hrs, respectively. A $5^{\circ}C$ increase in water temperature was achieved by the windheat generation system under the tested wind environment.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.