• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.3
• /
• pp.1288-1295
• /
• 2012

Korea Ministry of Knowledge Economy has estimated that wind power (WP) will be occupied 37% in 2020 and 42% in 2030 of the new energy sources, and also green energies such as photovoltaic (PV) and WP are expected to be interconnected with the distribution system because of Renewable Portfolio Standard (RPS) starting from 2012. However, when a large scale wind power plant (over 3[MW]) is connected to the traditional distribution system, protective devices (mainly OCR and OCGR of re-closer) will be occurred mal-function problems due to changed fault currents it be caused by Wye-grounded/Delta winding of interconnection transformer and %impedance of WP's turbine. Therefore, when Double-Fed Induction Generator (DFIG) of typical WP's Generator is connected into distribution system, this paper deals with analysis three-phase short, line to line short and a single line ground faults current by using the symmetrical components of fault analysis and PSCAD/EMTDC modeling.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1201-1208
• /
• 2022

In general, to maximize the supply and efficiency of floating offshore wind power generation energy, the motion caused by wave attenuation of the substructure must be reduced. According to previous studies, the motion response was reduced due to the vortex viscosity generated by the damping plate installed in the lower structure among the waves. In this study, a 5 MW semi-submersible OC5 platform and two platforms with attenuation plates were designed, and free decay experiments and numerical calculations were performed to confirm the effect of reducing motion due to vortex viscosity. As a result of the model test, when the heave free decay tests were conducted at drop heights of 30 mm, 40 mm, and 50 mm, compared with the OC5 platform, the platform with two types of damping plates attached had relatively improved motion damping performance. In the model test and numerical calculation results, the damping plate models, KSNU Plate 1 and KSNU Plate 2, were 1.1 times and 1.3 times lower than OC5, respectively, and the KSNU Plate 2 platform showed about two times better damping performance than OC5. This study shows that the area of the damping plate and the vortex viscosity are closely related to the damping rate of the heave motion.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.1
• /
• pp.13-20
• /
• 2007

This study was performed to provide fundamental data for long-term geomorphic predictions of estuarine sandbars in the Nakdong River. We monitored the geomorphic changes of Jinudo (Jinu Island), which is located on the far-southern side of the first western sandbar. We evaluated the temporal and spatial dynamics of the sandbar and the relationship between erosion and deposit speed with environmental factors. We found that: 1) The south side of Jinudo showed very rapid water channel closing and shoal generation. This phenomenon was more obvious during autumn (September and October) than during spring, with greater water depth reduction and variation between sides. 2) The mean deposit speed for Jinudo was approximately 0.85 mm/day. The deposit speed was 1.32 and 1.26 mm/day for the east and south sides of Jinudo, respectively. The maximum deposit and erosion speeds were 27 mm/day and 26 mm/day in July and December, respectively, on the east side of the island. 3) Mean surface deposit size was 0.18-0.26 mm. The newly deposited sandbar had a rotatively larger deposit size than the original land. 4) Correlation analysis showed that, on the southern side of the island, deposit activity prevailed in the winter due to low precipitation and a northerly wind, while erosion was dominant in the summer due to high water flow and a southerly wind. In contrast, the correlation analysis for the eastern side of the island showed that deposition is dominant when water flow is high. These results indicate that geomorphic dynamics vary among island sides.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.6 no.2
• /
• pp.38-45
• /
• 2003

This paper intends to analyze the movement characteristics of the suspended solid(SS) generated in a riprap work which is the most widespread process in harbor construction. The generation and movement behaviors of SS are investigated when 1) basic ripraps (0.001~0.03㎥) are cast for breakwater construction, 2) ripraps are loaded on carrier for riprap casting in the sea-wall construction of dredged material pocket, and 3) ripraps for inner filling are cast. The result of the present study shows that the SS generation is considerable when basic ripraps are cast for breakwater construction and the SS diffusion reaches up to 500m in high tide period. When ripraps are loaded on carrier, the SS is generated by the ripraps running down into sea from carrier, thereby showing a high concentration of SS in the vicinity of carrier. In the surface layer, SS distribution is confined in the vicinity of the carrier due to the prompt sinking of the SS. However the SS in the bottom layer is diffused approximately up to loom and then the SS concentration reaches to the background one. In the riprap (less than 0.03㎥) casting for inner filling using pork crane, SS is diffused approximately up to 300m in the surface layer and more than 300m in the bottom layer. It is quite interesting that the movement of the SS generated in harbor construction is mainly controlled by wind drift in the surface layer and tidal current in the bottom layer, and also the diffusion range of SS in the bottom layer is much larger than that in the surface layer.

• Ocean and Polar Research
• /
• v.36 no.1
• /
• pp.59-69
• /
• 2014

The long-term mooring performed at a KOGA station, located at about $30^{\circ}20^{\prime}N$, $126^{\circ}12^{\prime}E$ in the East China Sea shelf, shows some different behaviors between "semi-diurnal" and "diurnal currents" defined as the currents with periods around, respectively, a half day and a day. They appear to be predominantly tidal having significant coherences with sea level changes around the semi-diurnal and diurnal frequencies. The "semi-diurnal current" is strongly barotropic all year round. However, contrastingly, it is largely baroclinic in summer in the area about 70 km nearer to the continental slope, referred to as the "slope-area", as was found in previous current observations. The "diurnal current" of tidal origin is strongly barotropic in winter. In spring and summer, however, it becomes more baroclinic although it still remains largely barotropic, also showing more of its barotropic nature than in the "slope-area". The inertial oscillation contributing to the "diurnal current" appears to be more prominent when the current is baroclinic, indicating the important role played by stratification in generation of inertial oscillations. Downward energy propagation of inertial oscillation is not observed, suggesting that it is not created at the surface by wind. Considering that the study area is both near a critical latitude and proximity to the continental slope, it is suggested that parametric subharmonic instability (PSI) plays a significant role in creating the baroclinic inertial oscillation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.36-36
• /
• 2010

Currently, there are several newly developed energy resources for the future to replace petroleum resources such as hydrogen fuel cell, solar cell, wind power, and etc. Among them, solar cell has attracted a worldwide concern, because it has an enormous amount of resources. In general, a study of solar cells can be classified in to an area of bulk type and thin-film type. Inorganic solar cells based on silicon have been tremendously developed in technology and efficiency. However, since there are many lithographic steps, high processing temperature approximately $1000^{\circ}C$, and expensive raw materials, a manufacturing cost of device are nearly reaching a limit. Contrary to those disadvantages, organic solar cells can be manufactured at room temperature. Also, it has many advantages such as a low cost, easy fabrication of thin film, and possible manufacture to a large size. Because it can be made to be flexible, research and development on solar cells are actively in progress for the next generation. ever though an efficiency of the organic solar cell is low compared to that of inorganic one, a continuous study is needed. In this paper, we report optimal device structure obtained by a program simulation for design and development of highly efficient organic photovoltaic cells. we have also compared simulated results to experimental ones.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.653-660
• /
• 2015

In this study, we conduct power performance and load analyses of two different types of vertical-axis tidal-current turbines using the computational fluid dynamics (CFD) method. To analyze the power output and loads, we perform transient CFD simulations considering the cavitation model using ANSYS CFX. The averaged power output of an H-type rotor was 7.47 kW and 67.6 kW in normal and extreme operating conditions, respectively, which did not satisfy the initial design conditions. However, in the case of the helical-type rotor, the power output under normal and extreme conditions were close to the expected values. The cavitation, which may cause instantaneous power fluctuation, occurred repeatedly at the suction side of the rotors. In order to guarantee a more stable power supply and to prevent fatigue failure, we require a design that minimizes cavitation.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.8
• /
• pp.523-531
• /
• 2012

Recently, as a result of increasing concern about eco-friendly power, the demand for the power stations using environmentally friendly powers such as photovoltaic energy, wind force, tidal power, and tidal current has been increasing worldwide. Among these power stations tidal current power plant requires strong current generated by the topographic characteristics of the ocean floor. Uldolmok waterway producing very strong current is an ideal location for a tidal current power generation. However the occurrence of anthropogenic underwater noise generated by the tidal current power station may affect the marine environment. Therefore, it is necessary to evaluate the noise radiated from the station and predict the range influenced by the radiated noise. In this paper, the measurements of radiated noise spectrum level by the tidal current power station are presented, and the source level per unit area is estimated. Finally, the propagation properties of the radiated noise in the Uldolmok waterway is evaluated from the model simulation using the parabolic equation method, RAM.

• Journal of the Korea Convergence Society
• /
• v.2 no.2
• /
• pp.47-56
• /
• 2011

Korea Ministry of Knowledge Economy has estimated that wind power (WP) will be occupied 37% in 2020 and 42% in 2030 of the new energy sources, and also green energies such as photovoltaic (PV) and WP are expected to be interconnected with the distribution system because of Renewable Portfolio Standard (RPS) starting from 2012. However, when a large scale wind power plant (over 3[MW]) is connected to the traditional distribution system, protective devices (mainly OCR and OCGR of re-closer) will be occurred mal-function problems due to changed fault currents it be caused by Wye-grounded/Delta winding of interconnection transformer and %impedance of WP's turbine. Therefore, when Double-Fed Induction Generator (DFIG) of typical WP's Generator is connected into distribution system, this paper deals with analysis three-phase short, line to line short and a single line ground faults current by using the symmetrical components of fault analysis and PSCAD/EMTDC modeling.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.2
• /
• pp.137-143
• /
• 2016

The sedimentary environment and sediment were surveyed at the West-Northern site of Chagwi-do nearby Jeju Island for the design of the embedded suction anchor system of 10 MW-class floating wave-offshore wind hybrid power generation system. According to the classification scheme of Chough et al.[2002], the echo type of the seismic profiles using the chirp III was classified. As a results, the center and west-northern area of survey site were proved to be type I-3 where subbottom layer with thickness 5~15 m exists under the flat seafloor. On the other hands, the east-southern area were regarded to be type I-1, I-2 and III-1 where seafloor reflection is much stronger than type I-3. Also, the physical tests (unit weight, moisture content, grain size, liquid limit, specific gravity) were performed with samples taken from 8 fixed locations. It is found that the sand (SP), the sand blended with silt (SM) and the mixture of SP-SM are distributed uniformly on the survey area.