• Journal of Welding and Joining
• /
• v.21 no.2
• /
• pp.57-63
• /
• 2003

Since new types of vehicles or structures made from thin aluminum alloy are under rapid development and some products are already on the market, welding of aluminium sheet is increasing. MIG(Metal Inert Gas), MIG-Pulse, TIG(Tungsten Inert Gas) welding are the typical Ai welding. MIG welding has the advantage of high speed, but it is difficult to apply to the thin plate, because of bum-through by the high heat input and spatter. MIG-Pulse welding can weld without spatter and burn-through, but when the gap exists at the welding joint, there is quite a possibility of bum-through. TIG welding is difficult to weld at a high speed. AC Pulse welding alternates between DCEP(Direct Current Electrode Positive) and DCEN(Direct Current Electrode Negative). DCEN is higher wire melting rate than DCEP, while lower temperature of droplet than DCEP. In AC Pulse welding, far fixed welding current, wire melting rate increases as the EN ratio increases. For fixed wire feed rate, welding current decreases as the EN ratio increases. Because of these features, the temperature of droplet, the depth of penetration, the width of bead decrease and the reinforcement height increases as EN ratio increases, and these are able to weld at a high speed, lower heat input. It is the purpose of this study that design of AC pulse current waveform for MIG welding of Al sheet and estimation of output characteristic.

• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.76-81
• /
• 2007

The objective of this study is to find the optimum design of a snubber using CFD analysis. Several dimensions such as snubber height(H), snubber diameter(D), buffer width and buffer angle are considered in this study. The present study shows that the CFD can be applied to study the pressure characteristics inside the snubber. The objective of the snubber design optimization are to minimize a pressure loss and the pulsation ratio. Numerical results such as particle track, pressure distribution and turbulent kinetic energy are used to analyze the critical area and pressure behavior inside the snubber. As a result, snubber model with H/D ratio of 3.23 and buffer angle of $40^{\circ}$ has a minimum pressure loss. On the other hand, snubber model with H/D ratio 4.41 and buffer angle $10^{\circ}$ has a minimum pulsation ratio.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.4
• /
• pp.24-29
• /
• 2011

Conceptual study of an open-circuit type low-speed wind tunnel for performance test of wind turbine blade and airfoil is conducted. The tunnel is constituted of a settling chamber, a contraction, closed test section, a diffuser, two corners, a cross leg and a fan and motor. For the performance test, the closed test section width of 1.8 m, height of 1.8 m and length of 5.25 m is selected. The contraction ratio is 9 to 1 and maximum speed in the test section is 67 m/sec. Input power in the tunnel is about 238 kW and its energy ratio is 3.6. The wind tunnel designed in present study will be an effective tool in research and development of wind turbine and airfoil.

• Wind and Structures
• /
• v.35 no.2
• /
• pp.93-108
• /
• 2022

Steel tubular towers are commonly used in UHV and long crossing transmission lines. By considering effects of the model scale, the solidity ratio and the ratio of the mean width to the mean height, wind tunnel tests under different wind speeds on twenty tubular steel tower body models and twenty-six tubular steel cross-arm models were completed. Drag coefficients and shielding factors of the experimental tower body models and cross-arm models in wind directional axis for typical skewed angles were obtained. The influence of the lift forces on the skewed wind load factors of tubular steel tower bodies was evaluated. The skewed wind load factors, the wind load distribution factors in transversal and longitudinal direction were calculated for the tubular tower body models and cross-arm models, respectively. Fitting expressions for the skewed wind load factors of tubular steel bodies and cross-arms were determined through nonlinear fitting analysis. Parameters for skewed wind loads determined by wind tunnel tests were compared with the regulations in applicable standards. Suggestions on the drag coefficients, the skewed wind load factors and the wind load distribution factors were proposed for tubular steel transmission towers.

• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.49-55
• /
• 2012

The tandem welding process is one of the most efficient welding processes widely used in material joining technique such as manufacturing of strong and durable structures. It facilitates high rate of joint filling with little increase in the overall rate of heat input due to the simultaneous deposition from two electrode wires. The two electrodes in tandem welding process helps in high-efficiency and high productive of welding process. In this study a automated tandem welding system is developed to determine the correlation between cathode and anode and compared with current ratio of the two electrode torch. Three different inter-electrode distances were chosen, 25mm, 35mm and 45mm to perform the experiment with three different current ratio. From the experiment results, the current ratio between two torch has a large impact on width, height and depth of penetration. In addition, a stable bead geometry is obtained when inter-electrode distance is 35mm.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.1-10
• /
• 1996

The frequency distribution diagrams of Korean diffuse-porous woods, 36 families, 75 genera, 145 species, 215 specimens in relation to habit and phenology were analyzed. As the habit character changes from shrub to tree, such quantitative features as vessel frequency, percentage of solitary vessels, length/diameter(L/D) ratio of vessel element decreased but tangential vessel diameter, fiber length/vessel element length(F/V) ratio increased. Qualitative features such as helical vessel wall thickening, diffuse distribution of longitudinal parenchyma, heterogeneous ray composition decreased, while alternate intervessel pits, libriform wood fiber, simple perforations increase. As the phenology character changes from evergreen to deciduous species, such quantitative features as percentage of solitary vessels, vessel element length and L/D ratio decreased but tangential vessel diameter, F/V ratio increased. Diffuse distribution of longitudinal parenchyma, heterogeneous ray composition, and crystals in qualitative features decreased, while alternate intervessel pits, libriform wood fiber, simple perforation of vessel element, ray width and ray height increased.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.4
• /
• pp.171-181
• /
• 2000

A series of model tests were performed both to investigate the load transfer by soil acrching in fills above embankment pils and to verify of the theoretical analysis. In the model tests, the piles were installed in a row below the embankment and the cap beams were placed on the pile heads perpendicular to the longitudinal axias of the embankment. The space between pile cap beams and the embankment height was focused as the major factors affecting the load transfer in embankment fill. When the embankment fill was higher than the minimum required height, which was about 33% higher than the radius of the soil arch proposed by theoretical discussion in the previous study, not only the soil arching could be developed completely but also the experimental results showed good agreement with theoretical predictions. The portion of the embankment load carried by model pile cap beams decreased with increment of the space between pile cap beams, while it increased with increment of the embankment height. Therefore, to maximize the effect of embankment load transfer by piles on design, the interval ratio of pile cap beams should be decreased under considerably high embankments by reducing the space between cap beams and/or enlarging the width of pile cap beams.

• Asian Journal of Turfgrass Science
• /
• v.24 no.2
• /
• pp.97-105
• /
• 2010

This study focuses on investigating morphological characteristics and variations level in native zoysiagrasses from costal regions and islands in South Korea. In addition, this were collected to conserve germplasm for the breeding of zoysiagrass. One hundred fifty-nine of native zoysiagrasses were collected from 16 different cities and districts. There were morphological evaluations, including plant height, leaf width, leaf length, leaf angle, seed length(SL), seed width(SW), SL/SW ratio and number of seed per spike in native zoysiagrasses. Type of Z. japonica, Z. sinica, Z. macrostachya and Z. matrella showed significant variations in plant height, leaf length, leaf angle and number of seed per spike depending on where they were collected from. On the other hand, little variation were found in leaf width, seed length, seed width and SL/SW ratio. We have discovered a variety of variations among the investigated traits in hybrid zoysiagrass. These results can be used as basic information for development of zoysiagrass breeding.

• Journal of Bio-Environment Control
• /
• v.31 no.3
• /
• pp.163-169
• /
• 2022

This study was conducted to examine an alternative cultivating method that uses coir substrates in a hydroponically cultured system. Three treatment conditions were applied with one-layer substrate (10 cm height) with a coir chip and dust ratio of 5:5 (Treatment A), two-layer coir substrate (20 cm height) with a coir chip and dust ratio of 5:5 (Treatment B), one-layer coir substrate (15 cm height) with a coir chip and dust ratio of 7:3 (Treatment C). The control condition was a plastic container filled with a coir chip and dust ratio of 5:5. Various criteria were measured and compared between the treatments and the control. The yield of strawberry was smaller in the control than in the treatments. No significant difference in growth characteristic was found in the height treatments of the coir substrates. The net photosynthetic rate of the treatments was 14.68-15.76 µmol CO₂·m^-2·s^-1. This does not show a statistically significant difference. The root activity was better in treatment B and C than in treatment A and the control. The length and width of leaves were measured as 4.04-4.13 cm and 3.26-3.34 cm. These results are not statistically significant. The leaf length and width ratio was 1.27 in the control and 1.24 in the treatments. The findings show that no statistically significant benefit was found when utilizing coir substrates with different height treatments in the hydroponic culture system. However, the harvested fruit per plant weights 72.38 g in treatment A and 48.69 g in treatment C. The number of harvested fruit was least in treatment C in which a coir chip and dust ratio of 7:3 was applied. Therefore, further research is needed to examine how the chip and dust ratio in coir substrate affects growth characteristics.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.4
• /
• pp.315-320
• /
• 2017

PURPOSE. The aim of this investigation was to analyze the dimensions of clinical crowns and to classify the crown and the gingival type in the anterior teeth in Korean young adults. MATERIALS AND METHODS. Casts were obtained from 50 subjects ranging in age from 24 to 32. Measurements of length and width were made on the casts using a pair of digital calipers on the entire dentition. Crown thickness and papilla height were also measured and MDW/CL (mesiodistal width to clinical length) and CW/CL (cervical width to clinical length) ratios of the maxillary anterior teeth were calculated. The K-clustering method was used for CW/CL to classify the anterior tooth shape into three groups (tapered, ovoid, and square), and one-way analysis of variance and Duncan's post-hoc comparison were used to evaluate statistical significance between the groups. Pearson's correlation analysis was performed between tooth shape and papillary height (PH) to demonstrate the correlation between tooth shape and gingival morphological characteristics. RESULTS. The average length of the maxillary central incisors was 9.89 mm; the mesio-distal width was 8.54 mm; and the ratio of width/length was 0.86 in Korean young adults. The average bucco-palatal thickness of the central incisor was 3.14 mm at the incisal 1/3 aspect. Ovoid type was the most common tooth shape (48%), followed by square type (29%) and taper type (23%) in the central incisors of Korean young adults. Tooth shape and gingival type were correlated with each other. CONCLUSION. New reference data were established for tooth size in Korean young adults and the data show several patterns of tooth shape and gingival type. Clinicians should diagnose and treat based on these characteristics for better results in the Korean population.