• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.348-358
• /
• 2009

To satisfy the more severe emission regulation and the demand of higher fuel economy in near future, the combustion pressure and power output of engines is going to be higher. In order to get the reduction of engine emission and the higher power, it is needed the reduction of the tension and width of ring pack. The lower tension ring and the manufacturing technology of cast iron thinner width ring can bring the friction reduction between the ring and liner during engine running. Therfore, the fuel economy can be achieved. Thereafter the engine emission can be reduced. In this study, by using a developed basic computer program that predicts the inter-ring pressure, the motion of ring and the inter-ring pressure through a crevice volume model between adjacent rings, and the oil film thickness and the friction computed by lubrication theories, it is to be examined the effect of friction reduction from piston ring pack equipped with thinner width ring and lower tension ring.

• Journal of the Korean Home Economics Association
• /
• v.36 no.6
• /
• pp.85-94
• /
• 1998

In this study we tested the physiological influence on human-body according to clothing pressure with reduction rate and varied posture using three kinds of belt with different width. The width of belts were 2.5cm, 3.5cm and 4.5cm, and reduction rates of belts were 0%, 2.5% and 5% of the subject/s waist size respectively. the measured postures were standing state and sitting stste in the chair. The reasults are as follows; 1. Clothing pressure was high in the order of Side part>Front part>Back part and the rate fo change in the side part was highest, according to the reductio rate of belts. The more the width of belt was wide, the less the clothing pressure was small, and this kind of phenomenon could be explained by "The Principle of the power". 2. Both the rate of reduction of belt and the change of average skin temperature in accordance with the width of belt is small, however, the more the width of belts is wider and the reduction rate is bigger, the more the skin temperature at the waist part is increased. 3. The blood pressure and pulse was influenced when the width of belt was narrow and the reduction rate was high. 4. A sense restraining was much influenced by the width of belt, especially when the width of belts was wide, the significant difference was permitted.permitted.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.544-548
• /
• 2007

In general, final width of hot strip should be accomplished in this stage because width reduction of strip hardly appears during typical finishing mill. However, it is difficult to control the width of strip in the roughing mill process as the horizontal rolling of strip is subsequently performed after the vertical rolling. It is therefore important to obtain the deformation rolling direction on strip width to minimize the width spread of strip during horizontal rolling after vertical rolling. Generally there is Sizing press type and Edger-roll type. The width reduction process in sizing press has small amount of width spread compared with the edger. However, productivity by the sizing press process is much lower than those of the edger. In this study, sizing press and Edger-roll process parameters in a sheet rolling mill were set at specified values and the effect of the change in these parameters on product quality and process performance were evaluated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.650-650
• /
• 2013

Although imprinted nanopatterns of organic polymer can be modified by the heat treatment [1], it generally requires high process temperatures and is material-dependent since the heat-induced mass loss of the organic polymer is greatly affected by its chemical characteristics. When oxygen is added during the annealing process, one can reduce the process temperature as well as the dependence of the materials. With the oxygen, line width reduction of a polymer (SU-8) patterns could be accomplished at temperature of as low as $250^{\circ}C$ which was not possible in the heat only process. This oxidative line width reduction can be dramatically promoted with the introduction of oxygen plasma. The oxygen plasma, with its highly-reactive oxygen species, vigorously etches away the organic materials, proven to be extremely effective line with reduction method. It is, however, very hard to control the extent and homogeneity of the etching, particularly of very fine patterns. Here, we report an effective and reliable line width reduction method of imprinted nanopatterns by combined plasma and heat treatment. The merits of this process include the reduction of process temperature, time and material-dependence.

• Transactions of Materials Processing
• /
• v.4 no.2
• /
• pp.151-158
• /
• 1995

In this study, the width spreads of spring steel including Mn-Cr steel(SUP 9A), Mn-Cr-V steel(SUP 11A), and Si-Cr steel(SAE 9254) and were investigated under different reduction ratios and thickness-width ratios friction coefficients. The experimental results were compared with the theoretical prediction by the Ekelund equation, Geuze equations, etc. The width spreads of the three spring steels were found to be 10-15% larger than mild steel, and the optimal reduction ratio for the spring steel was found in a range from 20 to30%. Among the spring steels, the width spread of Mn-Cr-V steel was measured to be the largest followed by those of Si-Cr steel and Mn-Cr steel. It was found that the width spread increased with friction coefficient, width-thickness ratio and reduction ratio as predicted. However, the theoretical predictions revealed smaller width spread than the experimental results. This finding indicates that the coefficients of the width spread of the theoretical models need to be modified in order to predict the actual behavior of the width spreading of the spring steels. In this study, the coefficients of width spread of the Geuze equation were determined from the experimental results.

• Transactions of Materials Processing
• /
• v.12 no.7
• /
• pp.668-674
• /
• 2003

Rigid-plastic finite element analyses on the deformation of slabs at various width reductions have been performed. By using commercial finite element code, dog-bone profile, crop profile and the longitudinal width profile after edging and Horizontal rolling have been analysed. The deformation behavior of slab for the heavy edger mill has also been compared with that for the sizing press. From the deformation analyses, it was found that the sizing press-horizontal rolling method is more efficient in width reduction than that of heavy edger mill-horizontal rolling. The results of finite element analyses fer the deformation of slab were well confirmed by the actual operational data. It was found that the amount of width variation after sizing and rolling is about 5∼10mm.

• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.261-266
• /
• 2022

Notably, laser surface patterning facilitates tribological applications under lubricated sliding contacts. Consequently, a special pattern that can reduce the coefficient of friction under contact is considered necessary for improved machine efficiency. However, inappropriate pattern designs produce higher friction coefficients and cannot reduce friction. In this study, we use cast iron pins as specimens to investigate their friction and wear characteristics. Moreover, we experimentally investigate the correlation between the friction reduction effect and the design of groove crosshatch patterns fabricated with various angles and widths. We conduct a friction test using a pin-on-disc type tribometer under grease lubrication to study the friction reduction effect of the specimens, and we observe that the average coefficient of friction changes with the crosshatch angle and width. The experiment reveals that grooved crosshatch specimens with a crosshatch angle of 135°maximize friction reduction. The coefficient of friction of the groove specimens with a width of 120 ㎛ is lower than that of the specimens with a width of 200?. The friction reduction effect of the width of the groove is attributed to the density of the groove pattern. Thus, grooved crosshatch patterns can be designed to maximize friction reduction, and the friction property of a grooved crosshatch pattern is found to be related to its width and angle.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.223-225
• /
• 2007

Online models predicting roll force and forward slip of roughing mill was developed using nondimensional parameters. Using the effective inlet thickness, roll force model take into account the effect of inlet dog-bone shape of slab which take places after width reduction through edger rolling in roughing mill. The prediction accuracy of the proposed model is examined through comparison with measurements.

• The korean journal of orthodontics
• /
• v.30 no.3 s.80
• /
• pp.367-375
• /
• 2000

If a mandibular prognathic patient has an extremely unnatural anteroposterior and vertical maxilla or keen esthetical perception for facial profile, orthognathic surgery must be performed along with orthodontic treatment, which alone cannot provide satisfactory results in this case. Esthetical improvement becomes an important factor in the satisfaction level of the patient's treatment result, but an attempt to objectively measure beauty holds many problems. Therefore, in the end, the patient submits the final esthetical evaluation based on his/her subjective viewpoint. Because Korean people have a tendency to prefer the facial appeareance of westerners, they favor an oval shaped face over the traditional round face. This research was conducted in response to the complaints raised by patients who claim that their face had become more round from widening of facial width after the orthognathic surgery for manidibular prognathism than before the surgery. The following results were obtained on the changes in facial appearance and patient satisfaction level by analyzing the skull P-A analysis of total of 14 patients (8 male and 6 female) who underwent orthognathic surgery primarily chief complaint for manidibular prognathism and from their responses on questionnaires. These results are to be used in the research on the pre- and post- operative changes in facial height and width from orthognatic surgery. 1. Three ($21.4\%$) of 14 patients said that their face had widened. 2. The A group showed no change in mandibular width but B group showed a 0.7mm reduction. The facial width increased by 0.45mm and 0.66mm in groups A and B, respectively, after the orthognathic surgery 3. After the surgery the facial length changed by an 0.52mm increase in upper facial height , 1.19mm reduction in lower facial height, and 0.7mm reduction in mandibular height in group A. In group B group, there was a 0.67mm reduction in upper facial height, 3.66mm reduction in lower facial height, and 5mm reduction in mandibular height. 4. In reference to facial width, the facial height showed $1.5\%$ reduction in group A and $3.6\%$ reduction in group B after the surgery. 5. In reference mandibular height-to-facial width ratio, there was a $1.3\%$ reduction in group A, and $4.4\%$ reduction in group B after the surgery. 6. In reference to the mandibular height-to-width ratio, there was a $1.3\%$ reduction in group A and $4.3\%$ reduction in group B after the surgery. 7. Although the change in the facial width due to surgery can be ignored, sufficient explanation should be Provided to the patient before surgery on the fact that the face can appear to be relatively wide because of the reduced facial length as result of the surgery.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.92-93
• /
• 2021

In the case of medical facilities, the evacuation time is delayed due to the decrease in the number of people in the hallway and exits due to the increase in the width of evacuation by using mobile beds, wheelchairs, crutches, etc. Accordingly, it is considered to secure evacuation capacity to reduce evacuation time according to corridor width and exit width. Accordingly, we would like to compare the standards related to the evacuation capacity of medical facilities in Korea and NFPA, derive differences, and use evacuation simulations to compare evacuation times according to changes in corridor width and exit width. In Korea, it is calculated based on the floor area by use, but in the case of NFPA 101, the number of evacuation routes, stair width, corridor exit width, and two-way door width was stipulated depending on the number of people. Using evacuation simulation, efficient evacuation capacity is calculated according to the reduction of evacuation time by changing the width of the hallway, changing the width of the exit, the width of the corridor, and the width of the exit. The evacuation simulation is intended to be used to secure evacuation safety of domestic medical facilities by calculating the effective evacuation time reduction by changing the width of the hallway and exit.