• 조명전기설비학회논문지
• /
• 제29권11호
• /
• pp.6-17
• /
• 2015

In this paper, colors of broadcast lightings composed of Red, Green, and Blue LED(Light Emitted Diode) can be linearly and quantitatively controlled in low illuminance. Because LED cannot emit uniform illuminance in low illuminance, the colors of RGB LED are unmixable. Furthermore, the illuminances are nonlinear with the dimming values of the RGB LED due to the nonlinearity of the output illuminance with the current through the LED. This nonlinearity generated errors of the target colors and illuminances. The proposed algorithm set up the target colors, which is expressed by the color coordinates in CIE 1931 color space, and the target illuminances. Then the illuminances of RGB LED were calculated using color mixing theory. The calculated illuminances determined the dimming values of the RGB LED for transmission via DMX512 communication. After the broadcasting lighting received the dimming values of the RGB LED via DMX512 communication,.RGB LED can emit target color and illuminance, and be controlled by calculating the PWM(Pulse Width Modulation) duty ratio of the hybrid LED driver which be considered the nonlinearity for the illuminances of the LED. As a result, the proposed algorithm can linearly and quantitatively control the colors and illuminances in full range of illuminance. Then we verify experimentally that the errors of the emitted color coordination x, y and illuminance are 2.27%, 3.6% and 1.5%, respectively.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.205-208
• /
• 2008

The wind load on building surface is numerically investigated. The geometry of target building is a square cross section and aspect ratio (height (H) to width (d)) is 6. On building surface, the pressure was measured, compared to obtained value from numerical simulation. The numerical simulations were done using URANS with three different turbulence models such as v2-f model, k-${\omega}$model, and k-${\varepsilon}$ model, respectively. The v2-f model showed the best agreement with experimental data in simulating mean pressure coefficients on front, rear and side surface. But unsteady characteristics of pressure history measured on surface is shown a discrepancy between experiment and numerical simulation.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.761-768
• /
• 1999

This paper is studied to find the optimum condition of double-inlet Sirocco fan installed in an indoor PAC for low noise operation by the Taguchi method. The goal of this study is to obtain the best combination of each control factor which results in a desired flowrate of Sirocco fan with minimum variability. In this study, the parameter design of the Taguchi method is adopted for robust design by the dynamic characteristic analysis using orthogonal arrays and S/N ratios. The flowrate measurements are conducted by using a multiple-nozzle-type fan tester according to the orthogonal array L9($3^4$). The results of this study can be summarized as follows ; (i) The optimum condition of control factor is a set of where A is an inner to outer diameter ratio($D_1/D_2$), B is a width to outer diameter ratio($L/D_2$), C is a blade attachment angle(${\theta}$) and D is a number of blade(Z), (ii) The flowrate under the optimum condition satisfies the equation $y=0.0384{\cdot}M$ where M is a signal factor, namely number of revolution. The flowrate performance improves about 7.3% more largely as compared with the current condition, which results in about 35RPM reduction of number of revolution for the target flowrate $18.5m^3/min$, and (iii) The sensitivity analysis shows that the major factors in contribution to flowrate performance are A, B, and D ; the percentage contributions of each control factor are 44.01%(Z), 26.77%($D_1/D_2$) and 20.42%($L/D_2$).

• 한국음향학회지
• /
• 제20권7호
• /
• pp.31-36
• /
• 2001

수동 소나 시스템에서는 신호대 잡음비의 향상, 표적의 방위 탐지 및 위치 데이터 산출, 간섭신호 제거 등을 위하여 지향성 빔을 만들어 사용한다. 주변환경이 복잡한 해양에서 저소음의 표적을 원거리에서 탐지하기 위해서는 지향성 빔의 특성을 향상시킬 필요가 있다. 본 논문에서는 선형으로 배열된 센서에서 각 센서 쌍들의 상호상관 행렬을 이용한 SCCBF (Spatial Cross Correlation Beamforming) 알고리즘을 제안하였다. 이상적인 조건하에서 제안된 SCCBF는 기존의 CBF (Conventional Beamforming)에 비해 배열 이득이 3 dB 이상 향상되고 표적의 탐지 방위 정확도를 나타내는 빔 폭이 CBF보다 0.5배 정도가 됨을 이론적으로 검증하고, 시뮬레이션을 통하여 이를 입증하였다. 또한 제안된 알고리즘을 적용한 선배열 수동 소나 시스템의 해상 시험 결과를 제시하였다.

• 한국컴퓨터정보학회논문지
• /
• 제16권3호
• /
• pp.211-218
• /
• 2011

한반도 고지도들은 많은 역사적 의미를 가지고 있으므로, 이것을 분석하여 역사적인 사실들을 추정할 수 있다. 하지만, 고지도는 국부적인 영역들을 결합하여 전체적인 영토를 표현하기 때문에, 현재의 지도와 직접적으로 비교하는 것이 어렵다. 따라서 본 논문에서는 평가할 대상 고지도를 기준 지도의 특성에 맞게 회전, 크기 변환 및 위치이동을 수행하여 쉽게 영역을 비교할 수 있도록 변환한다. 한반도 영역의 주축을 계산하여 기준 지도의 주축의 차이만큼 회전하고, 외곽 사각형의 비율을 이용하여 비대칭적으로 폭과 높이의 크기를 수정한다. 마지막으로 영역의 중심을 일치하여 두 영역을 겹치고, 두 가지 유사도 수식을 이용하여 고지도를 평가한다. 실험 결과에서 영역 비율과 휘어짐 각도차의 유사도가 현대에 가까워지면서 유사도가 높아지는 것을 볼 수 있다. 따라서 제안하는 기법은 한반도의 고지도를 사료로 분석하는데 활용될 수 있을 것이다.

• Steel and Composite Structures
• /
• 제38권6호
• /
• pp.617-635
• /
• 2021

This paper numerically investigated the behavior of built-up square concrete-filled steel tubular (CFST) columns under combined preload and axial compression. The finite element (FE) models of target columns were verified in terms of failure mode, axial load-deformation curve and ultimate strength. A full-range analysis on the axial load-deformation response as well as the interaction behavior was conducted to reveal the composite mechanism. The parametric study was performed to investigate the influences of material strengths and geometric sizes. Subsequently, influence of construction preload on the full-range behavior and confinement effect was investigated. Numerical results indicate that the axial load-deformation curve can be divided into four working stages where the contact pressure of curling rib arc gradually disappears as the steel tube buckles; increasing width-to-thickness (B/t) ratio can enhance the strength enhancement index (e.g., an increment of 1.88% from B/t=40 to B/t=100), though ultimate strength and ductility are decreased; stiffener length and lip inclination angle display a slight influence on strength enhancement index and ductility; construction preload can degrade the plastic deformation capacity and postpone the origin appearance of contact pressure, thus making a decrease of 14.81%~27.23% in ductility. Finally, a revised equation for determining strain εscy corresponding to ultimate strength was proposed to evaluate the plastic deformation capacity of built-up square CFST columns.

• Journal of Astronomy and Space Sciences
• /
• 제37권4호
• /
• pp.219-228
• /
• 2020

A CubeSat platform has become a popular choice due to inexpensive commercial off-the-shelf (COTS) components and low launch cost. However, it requires more power-efficient and higher-data rate downlink capability for space applications related to remote sensing. In addition, the platform is limited by the size, weight and power (SWaP) constraints as well as the regulatory issue of licensing the radio frequency (RF) spectrum. The requirements and limitations have put optical communications on promising alternatives to RF communications for a CubeSat platform, owing to the power efficiency and high data rate as well as the license free spectrum. In this study, we analyzed the performance of optical downlink communications compatible with CubeSat platforms in terms of data rate, bit error rate (BER) and outage probability. Mathematical models of BER and outage probability were derived based on not only the log-normal model of atmospheric turbulence but also a transmitter with a finite extinction ratio. Given the fixed slot width, the optimal guard time and modulation orders were chosen to achieve the target data rate. And the two performance metrics, BER and outage data rate, were analyzed and discussed with respect to beam divergence angle, scintillation index and zenith angle.

• 한국광학회지
• /
• 제24권1호
• /
• pp.23-28
• /
• 2013

송광광학계의 광원으로 사용되는 광섬유 레이저의 개구수, NA가 0.13~0.22의 범위에 있으면, 이 NA에 관계없이 1 km 전방에서 빔직경이 4.8 m 또는 6.8 m이 되도록 줌렌즈형 광속확대기를 적용한 송광광학계를 설계하였으며, 표적에서의 foot prints를 통하여 빔직경을 확인하였다. $16{\times}16$($100{\mu}m{\times}100{\mu}m$) 픽셀 검출기를 사용하는 수광광학계를 설계하였으며, 검출면의 픽셀 위치에 따른 spot diameter는 모두 $55{\mu}m$ 이하가 됨을 확인하였다. 스캔을 고려하여 송광광학계를 수광부 대물렌즈에 내접하도록 구성하였으며, 이때 송광부에 의하여 가려진 부분은 11%가 되었다.

• 지적과 국토정보
• /
• 제46권2호
• /
• pp.5-25
• /
• 2016

본 연구는 국가공간정보포털에서 제공하는 국토정보들을 활용하여 빈곤 취약지구를 추출하는 방법론을 정립하는데 목적을 두었다. 빈곤 취약지구를 추출하기 위한 지표들을 선정하고 지표들의 작동성을 검정하였으며, 특히 빈곤 취약지구를 추출하는 위계적인 공간 영역에 따라 지표들의 활용이 조정 가능하도록 융통성있는 방법론을 구축하는데 초점을 두었다. 빈곤 취약지구를 추출하기 위한 지표들을 빈곤층, 노후불량주택, 근린불량주거환경의 세 영역으로 분류하고 각각의 영역에 적합한 대표 지표들을 선정하였다. 그 결과 행정동 차원에서 빈곤 취약지구 추출을 위한 핵심 지표는 천명당 기초생활수급자수와 노후단독주택 거주 가구 비율 지표로 나타났다. 국가기초구역 차원에서 근린불량주거환경을 나타내는 지표로는 불량도로 접도 주택비율, 과소필지 비율, 노후불량주택 비율이 상당히 중요한 지표로 나타났다. 본 연구에서는 소구역 단위에서 격자 분석을 통해 여러 지표들을 중첩시켜본 결과 상대적으로 더 빈곤하고 취약한 소구역을 추출할 수 있었다. 국가공간정보포탈에서 제공하는 데이터를 필요한 목적에 맞추어 활용하는 경우 고부가가치의 정보 창출 가능성을 보여주었다는 점에서 본 연구의 학술적 의의를 찾을 수 있다. 본 연구의 방법론은 빈곤 취약 우선 대상지구를 효율적으로 선정하는데 도움을 줄 수 있을 것이다.

• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.49-53
• /
• 1985

The effects of pre-treatments, the hot water extraction of wood meal and the addition of chemical ($CaCl_2$) to wood-cement water system on the properties of wood-cement composite such as modulus of rupture (MOR), modulus of elasticity (MOE), water sorption ratio and swelling ratio of resulting boards were studied in this experiment. The wood meals through 0.83mm(20 mesh) and retained on 0.42mm(35 mesh) screen were prepared from Pinus densiflora S. at Z. and Larix leptolepsis G. For hot water extraction, 500 grams of wood meal for each species were heated to boiling with 1,500ml of distilled water in 2-liter beaker for 6 hours. Every 2 hours, the wood meals were washed with boiling distil1ed water and reheated to boiling again. After 6 hours boiling, the boiled wood particles were collected by pouring this particles on 200 mesh screen. The collected particles then washed twice with hot distilled water and dried for 24 hours in an oven at $109{\pm}20^{\circ}C$. A mixture of 663.4 grams of cement with 331.7 grams of wood meal based on oven-dry weight were dry-mixed in a plastic vessel. The mixture was kneaded with 497.6ml of distilled water in the ratio of 1.5ml of water to a gram of wood meal. To add calcium chloride to the mixture as an accelerator, $CaCl_2$ 4% solution by weight per volume, was added to pine-or larch-cement board in the ratio of 3% to cement weight. To set wood-cement board, this mixture was clamped at 30cm ${\times}$ 30cm, in thickness of 1.5cm for 3 days at room temperature, declamped and then placed at open condition for 17 days. The target density was 1.0. The four specimens sized to 5cm in width and 28cm in length were used for MOR and MOE test for each treatment. After MOR test, the tested specimens were cut to the size of 5cm ${\times}$ 5cm for water sorption and swelling test. The twenty specimens used to measure the water sorption ratio (soaking 24 hours) and ten of these were used for swelling ratio measurement The results obtained were as follows: 1) Larch was not suitable for wood-cement boards because larch-cement board developed no strength, but pine showed 97.9kg/$cm^2$ by hot water extraction. 2) To increase MOR, hot water extraction was more effective than the addition of $CaCl_2$ in pine and larch because the $CaCl_2$ addition was seemed to speed up the ratio of cement hydration without reacting with the wood substances. 3) The water sorption ratio was lowered by the addition of $CaCl_2$ to wood-cement system because the chemical additive accelerated the rate of cement hydration. 4) In pine-cement board, the swelling ratio from 0.37 to 0.42 percent was observed in length and the swelling ratio from 0.88 to 2.0 percent in thickness. As a rule, the swelling ratio of wood-cement board was very low and the swelling ratio in thickness was higher than in length.