• 한국전자파학회논문지
• /
• 제14권12호
• /
• pp.1276-1282
• /
• 2003

SMT 타입의 페라이트 비드(ferrite bead)는 전원단에서 발생되는 잡음(noise)이 회로 소자로 유입되는 것을 막기 위해 사용되는 소자로 병렬 캐패시터(capacitor)와 직렬 인덕터(inductor) 및 저항(resistor)을 이용하여 등가 모델화된다. 이와 같은 간단한 페라이트 비드의 등가 모델은 광대역 범위에서 측정 결과와 일치하지 않는다. 본 논문에서는 광대 역(50 MHz∼3 GHz)에서 정확한 페라이트 비드의 모델을 제시하고 페라이트 비드가 있을 때와 없을 때 전원단 잡음의 회로 소자에 미치는 영향을 고찰하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.91-93
• /
• 2007

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.50-54
• /
• 2008

The wearplate with Cr-C has been used in condition of severe abrasion. Recently, the demand of wearplate made by hardfacing with Cr-C has increased in the world, but it is lack of supply and expensive due to low productivity. CMAW (Compound Metal Arc Welding) is very useful process of several welding methods to make wearplate. In this paper, twin torch CMAW to use twin torch at the same time was developed to improve productivity and to ensure quality of wear plate. When the distance between two touches was smaller than 30mm, arc blow was occurred. However when the distance was larger than 35mm, there was no arc blow any more. If the oscillation path of each torch was overlapped together, the melt through at the overlapped zone was occurred due to concentrated heat input in substrate. On the other hand, the turning point of each torch was open more than 5mm, separated bead was generated. Therefore twin torch CMAW which has adequate conditions was able to make wearplate having flatter surface at the bead connection than single torch.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.126-132
• /
• 2012

The GMA welding process involves large number of interdependent variables which may affect product quality, productivity and cost effectiveness. The relationships between process parameters for a fillet joint and bead geometry are complex because a number of process parameters are involved. To make the automated GMA welding, a method that predicts bead geometry and accomplishes the desired mechanical properties of the weldment should be developed. The developed method should also cover a wide range of material thicknesses and be applicable for all welding position. For the automatic welding system, the data must be available in the form of mathematical equations. In this study a new intelligent model with genetic algorithm has been proposed to investigate interrelationships between welding parameters and bead geometry for the automated GMA welding process. Through the developed model, the correlation between process parameters and bead geometry obtained from the actual experimental results, predicts that data did not show much of a difference, which means that it is quite suitable for the developed genetic algorithm. Progress to be able to control the process parameters in order to obtain the desired bead shape, as well as the systematic study of the genetic algorithm was developed on the basis of the data obtained through the experiments in this study can be applied. In addition, the developed genetic algorithm has the ability to predict the bead shape of the experimental results with satisfactory accuracy.

• Journal of Welding and Joining
• /
• 제26권4호
• /
• pp.44-49
• /
• 2008

Generally, wear plate is steel plate having improved surface contact strength and impact strength by surface hardening which is welded using materials with good corrosion resistance, wear resistance and thermal resistance property. CFP GMAW(Compound Filler Plate Gas Metal Arc Welding) is the cladding method using GMAW with the CFP, which is bound with waterglass, on the substrate. It has advantages of reducing compound powder loss, uniform penetration, and preventing hardness decrease. To develope mass production technique of CFP GMAW process for production of high quality wear plate, the method for controling shallow penetration and increasing productivity is required. In this study, twin torch method applied to CFP GMAW process for increasing productivity. And the method was developed by controling penetration control, CFP dry time, gas formation flux and water glass concentration. As a result, applying twin torch method to CFP GMAW process was possible and high quality wide bead could be made without overlap joint.

• 에너지공학
• /
• 제21권1호
• /
• pp.43-46
• /
• 2012

A fluidized bed drying approach was utilized to the synthesis of water glass based silica aerogel powders. The effects of the fluidized bed drying conditions such as the superficial velocity and temperature of hot air and bead size as well as bead/wet-gel ratio, on the physical properties such as tapping density and productivity of the aerogel powders were systematically investigated. The experimental results showed that the amount of beads mixed with wet-gels in the fluidized bed column has the most profound impact on the fluidization efficiency, greatly enhancing the yield of the aerogel powders up to 98% with a proper bead/wet-gel weight ratio as compared to 72% without using beads. No significant change was observed in the tapping density over a wide range of the fluidized drying condition. Consequently the fluidized bed drying approach shows a good promise as an alternative route for the large-scale production of the aerogel powders.

• Journal of Welding and Joining
• /
• 제8권3호
• /
• pp.70-78
• /
• 1990

The harsh nature of welding environments makes welding a prime candidate for process automation. Among the variety of welding processes available, gas metal arc welding is one of the most frequently used methods, primarily because it is highly suited to a wide range of applications, and also to automation. Automatic seam tracking method is one of the most demanded techniques for automatic control of arc welding. In this study a seam tracking system has been developed by using the welding arc itself as a sensor. This paper described the principle and experimental result of the arc sensor system, as well as the development and application of the automatic CO_2$ welding for the horizontal fillet welding. A basic problem in horizontal fillet welding is the prevention of hanging bead formation such as undercut at the vertical plate and overlap at the horizontal plate. To produce the symmetric bead shape, the relationship of bead shape to welding parameters(welding velocity, weaving width, weaving speed, tip to workpiece distance) was also investigated.

• Journal of Welding and Joining
• /
• 제30권5호
• /
• pp.70-75
• /
• 2012

This study is related to the laser weldability of AZ31B magnesium alloy, an all-purpose wrought alloy with good strength and ductility. In general, AZ31B is classified into AZ31B-H24 and AZ31B-O depending on temper designation. Thus, in this study, the laser weldability of AZ31B-H24 and AZ31B-O was investigated and compared. CW Nd:YAG laser was used to produce bead and butt joints. And the effects of welding conditions on the weldability of these joints were examined in detail. As a result of this study, AZ31B-H24 was found to have thinner oxide film and smaller grain size compared with AZ31B-O. Due to such difference, in bead welding, AZ31B-H24 had more wide welding range for full penetration compared with AZ31B-O. Furthermore, it was also confirmed that AZ31B-H24 and AZ31B-O have different welding conditions to obtain stable keyhole in butt welding.

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.22-28
• /
• 2013

Robotic GMA (Gas Metal Arc) welding process is one of widely acceptable metal joining process. The heat and mass inputs are coupled and transferred by the weld arc to the molten weld pool and by the molten metal that is being transferred to the weld pool. The amount and distribution of the input energy are basically controlled by the obvious and careful choices of welding process parameters in order to accomplish the optimal bead geometry and the desired quality of the weldment. To make effective use of automated and robotic GMA welding, it is imperative to predict online faults for bead geometry and welding quality with respect to welding parameters, applicable to all welding positions and covering a wide range of material thickness. MD (Mahalanobis Distance) technique was employed for investigating and modeling the GMA welding process and significance test techniques were applied for the interpretation of the experimental data. To successfully accomplish this objective, two sets of experiment were performed with different welding parameters; the welded samples from SM 490A steel flats. First, a set of weldments without any faults were generated in a number of repeated sessions in order to be used as references. The experimental results of current and voltage waveforms were used to predict the magnitude of bead geometry and welding quality, and to establish the relationships between weld process parameters and online welding faults. Statistical models developed from experimental results which can be used to quantify the welding quality with respect to process parameters in order to achieve the desired bead geometry based on weld quality criteria.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.161-162
• /
• 2000

We propose multi-layer aspheric lenticular lens for rear projection screen to provide wide viewing angle. Each pitch of lenticular lens sheet is divided by three region and image light from projection optical system is propagated widely on each region due to different focal point. Besides, to improve vertical viewing angle of screen, we propose glass bead embedded screen on observer side of lenticular lens.