• Journal of information and communication convergence engineering
• /
• v.18 no.3
• /
• pp.162-166
• /
• 2020

The present paper presents an array antenna of a microstrip patch for 5G applications. Four rectangular microstrip patch elements are arranged in parallel and series to form an array antenna. Two insets are made on both sides of each patch element to achieve a wide frequency bandwidth of 23.97-31.60 GHz. To attain a high gain and wider bandwidth, the microstrip patch antenna is fed using series and corporate feeding networks. Further, three director elements on top of the top-most patch elements, and one reflector element at the open end of each patch element, are added. The addition of the Yagi elements improved the overall gain and acquired a higher radiation efficiency throughout the operating frequency bandwidth, with the array antenna achieving a maximum peak gain of 8.7 dB. The proposed antenna is built on a low-loss and low-cost substrate of FR4-eproxy. The proposed antenna design with a simple structure is suitable for Internet of Things and 5G applications.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.791-794
• /
• 2003

The increasing computational capability of processors is driving the need for high bandwidth links to communicate and store the information that is processed. Such links are often an important part of multi processor interconnection, processor-to-memory interfaces and Serial-network interfaces. This paper describes a 0.11-${\mu}{\textrm}{m}$ CMOS 4 Gbp s/pin 3-Level transceiver using RSL/(Rambus Signaling Logic) for high bandwidth. This system which uses a high-gain windowed integrating receiver with wide common-mode range which was designed in order to improve SNR when operating with the smaller input overdrive of 3-Level. For multi-gigabit/second application, the data rate is limited by Inter-Symbol Interference (ISI) caused by low pass effects of channel, process-limited on-chip clock frequency, and serial link distance. In order to detect the transmited 4Gbps/pin with 3-Level data sucessfully ,the receiver is designed using 3-stage sense amplifier. The proposed transceiver employes multi-level signaling (3-Level Pulse Amplitude Modulation) using clock multi phase, double data rate and Prbs patten generator. The transceiver shows data rate of 3.2 ~ 4.0 Gbps/pin with a 1GHz internal clock.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.669-676
• /
• 2003

In this paper, a novel design method for an ultra-wide band TEM horn antenna is proposed on the basis of parallel plate waveguide theory. A principle of TEM modes generation is analyzed and the characteristics of this antenna are experimentally investigated. The proposed TEM horn antenna has an exponentially tapered structure to increase matching bandwidth. Also, the designed TEM horn has shortened length but increased aperture so that the bandwidth for cutoff frequency is increased. The measured result show that the proposed TEM hem antenna has the frequency band of 75 MHz to 1200 MHz for VSWR less than 2.0 and the bandwidth of the TEM horn becomes more than twice comparing to that of a linearly tapered TEM hem. It is anticipated that the manufactured antenna is applicable to UWB systems for impulse response measurement.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.707-714
• /
• 2016

We present a piezoelectric energy harvester with stopper-engaged dynamic magnifier which is capable of significantly increasing the operating bandwidth and the energy (power) harvested from a broad range of low frequency vibrations (<30 Hz). It uses a mass-loaded polymer beam (primary spring-mass system) that works as a dynamic magnifier for another mass-loaded piezoelectric beam (secondary spring-mass system) clamped on primary mass, constituting a two-degree-of-freedom (2-DOF) system. Use of polymer (polycarbonate) as the primary beam allows the harvester not only to respond to low frequency vibrations but also generates high impulsive force while the primary mass engages the base stopper. Upon excitation, the dynamic magnifier causes mechanical impact on the base stopper and transfers a secondary shock (in the form of impulsive force) to the energy harvesting element resulting in an increased strain in it and triggers nonlinear frequency up-conversion mechanism. Therefore, it generates almost four times larger average power and exhibits over 250% wider half-power bandwidth than those of its conventional 2-DOF counterpart (without stopper). Experimental results indicate that the proposed device is highly applicable to vibration energy harvesting in automobiles.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.206-216
• /
• 2000

In this paper, the linear tapered slot(LTS) antenna and linear constant tapered slot(LCTS) antenna are optimized for millimeter-wave antenna by the finite difference time domain(FDTD) method and then fabricated and measured. The microstrip-to-slot transition is proposed with the widen $\lambda$/4 open stub as feeder for wide bandwidth of 16.5GHz($VSWR\leq2$). The results of the calculation and measurement, the bandwidth of LTS antanna is 8.3GHz(26.47%) and 7.1792GHz(22.4%) respectively. Also, the bandwidth of LCTS antenna is 8.1GHz(26.47%) and 6.3243GHz(20.43%) respectively.

• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.19-23
• /
• 2016

This paper presents a novel design for dual-band bandpass filters. The proposed filters are applicable to the carrier aggregation of the TV white space (TVWS) band and long-term evolution (LTE) band for cognitive radio applications. The lower passband is the TVWS band (470-698 MHz) whose fractional bandwidth is 40 %, while the higher passband is the LTE band (824-894 MHz) with 8 % fractional bandwidth. Since the two passbands are located very close to each other, a transmission zero is inserted to enhance the rejection level between the two passbands. The TVWS band filter is designed using magnetic coupling to obtain a wide bandwidth, and the LTE band filter is designed using dielectric resonators to achieve good insertion loss characteristics. In addition, in the proposed design, a transmission zero is placed with cross-coupling. The proposed dual-band bandpass filter is designed as a two-port filter (one input/one output) as well as a three-port filter (one common input/two outputs). The measured performances show good agreement with the simulated performances.

• Journal of information and communication convergence engineering
• /
• v.22 no.1
• /
• pp.14-22
• /
• 2024

This study presents the design of a Wilkinson power divider for three-way output ports (WPD3OP), which incorporates a defected ground structure (DGS). An asymmetric power divider is integrated into the output ports of the conventional Wilkinson power divider (WPD), establishing a three-way output port configuration. The DGS introduces periodic or irregular patterns into the ground plane to suppress unwanted electromagnetic wave propagation, and its incorporation can enhance the performance of the power divider, in terms of the power-division ratio, isolation, and bandwidth, by reducing spurious resonances. The proposed design algorithm for an asymmetric power divider for three-way output ports is analyzed via circuit simulations using High-Frequency Simulation Software (HFSS). The results verify the validity of the proposed method. The analysis of the WPD3OP integrated with DGS certifies the achievement of a center frequency of 2 GHz. This confirmation is supported by schematic ideal design simulation results and measurements encompassing insertion losses, return losses, and isolation.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.314-319
• /
• 2015

The conventional geometry of a plate microstrip resonator is made up of a single metallic patch, which is printed on a monolayer dielectric substrate. Its arrangement is simple and easy to make, but it is limited in its functional abilities. Many searches have been realized to improve the bandwidth and the gain of the microstrip resonators. Among the various configurations proposed in the open literature, the stacked geometry seems to be very promising. By appropriate design, it is able to provide the operation in dual frequency mode, wide bandwidth enough and high gain. The theoretical investigations of structures composed of two stacked anti-reflection coatings, enhanced metallic coatings are available in the literature, however, for the stacked configurations involving three metallic coatings or more, not to exact or approximate analysis was conducted due to the complexity of the structure.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.318-321
• /
• 1991

For measuring the transient electromagnetic fields and related quantities created by disconnector operations in GIS, one needs the wide bandwidth sensors with simple transfer functions. This paper describes a new developed electric field sensor to measure the very fast transient electric fields and voltages, and the measuring principle, design and construction of planar electric field sensor are described. A calibration and/or correction technique of the sensor is investigated which enables an accurate determination of the sensor response to the time-changing electric fields. As a consequence, the low voltage calibrations certify that a rise time of 1.7 [ns] is achieved for the planar electric field sensor and a total bandwidth extending from several Hz to 200 MHz for the measuring system which presents the constant division ratio as a function of frequency.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.1
• /
• pp.65-71
• /
• 2003

In a high speed spindle system it is very important to monitor the state of rotating rotor. Particularly in active control spindle system the position sensor must provide feedback to the control system on the exact position of the rotor. In order to monitor the state of a high speed spindle exactly, high accuracy and wide frequency bandwidth of sensors are important. The focus in this paper is to make a fiber optic sensor for monitoring rotor of magnetic bearing, to design the circuit for detecting optical signal, and to evaluation static and dynamic characteristics of fiber optic sensor.