• Korean Journal of Applied Biomechanics
• /
• v.21 no.4
• /
• pp.429-436
• /
• 2011

In this study, we have experimented with 9 players at the national delegate level. Although there were some differences in the average effects of 3 types of one-two straight movements after the application of wheel axle, there were no statistical differences in the case of surface reacting forces, electromyograms, and impact forces. When the right fist was impacted using the one-two straight movements and the wheel axle was applied with 3 segmentations, high impact forces were obtained for the pronation in the following order-72.01 $m/s^2$ (type 2), 70.93 $m/s^2$ (type 3), and 58.19 $m/s^2$ (type 1). Higher values of the surface reacting force were found for type 1 that did not exhibit pronation in the left foot, whereas in the case of the vertical direction of the right foot, type 2 with pronation exhibited higher values and impact forces. In the right electromyogram, high impact forces due to the activation of the muscular electric potential were obtained for lumbar erector (LE) spinae and triceps brachii (TB) with type 1; LE spina, latissimus dosi (LD), and upper trapezius (UT) with type 2; and brachioradialis (BR), UT, and rectus abdominal (RA) with type 3. Due to pronation and complex motions of the 3 pronation segmentations, the efficiency was higher for impacts due to one-two straight movements.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.4
• /
• pp.418-424
• /
• 2017

A wheel dynamometer was installed between the rim and axle hub to measure the forces and moments applied to a vehicle. The wheel dynamometer was composed of sensing and signal processing components. Because the sensing component contained a complex structure to sense the six components of the forces and moments and the wheel rotated along with the vehicle movement, sophisticated signal processing hardware and a software algorithm were used. The strains and the calibration matrices of the wheel dynamometer along the wheel rotation angle were investigated using FEM. From the analysis, the calibration matrices were simplified using a spline interpolation. Based upon these results, the signal processing component could be effectively designed and the firmware software could be simplified.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.138-143
• /
• 2006

Oscillatory wheel load fluctuation of considerable amplitude is almost always observed on railway vehicle running at high speed. From the acceleration measured on the axle-box, the frequency of this fluctuation is estimated to be approximately within 70 Hz. By the conventional measuring method, continuous outputs of wheel load can not be obtained, so it is difficult to investigate such a high frequency phenomenon exactly. We have developed a new method of measuring the forces and derailment coefficient continuously, using two pairs of strain gauge bridges whose output phases are shifted by 90 degree, and summing up the outputs with a weighting function. This method is available for measuring the forces between wheel and rail up to high frequency. In this paper, continuous method of measuring forces between wheel and rail and derailment coefficient.

• Journal of the Korean Society for Railway
• /
• v.14 no.3
• /
• pp.203-210
• /
• 2011

This study formulates the theoretical wheel-set model to evaluate wheel-climbing derailments of rolling stock due to collision, and verifies this theory with dynamic simulations. The impact forces occurring during collision are transmitted from a car body to axles through suspensions. As a result of combinations of horizontal and vertical forces applied to axles, rolling stock may lead to derailment. The derailment type will depend on the combinations of the horizontal and vertical forces, flange angle and friction coefficient. According to collision conditions, the wheel-lift, wheel-climbing or roll-over derailments can occur between wheel and rail. In this theoretical derailment model of wheelset, the wheel-climbing derailment types are classified into Climb-over, Climb/roll-over, and pure Roll-over according to derailment mechanism between wheel and rail, and we proposed the theoretical conditions to generate each derailment mechanism. The theoretical wheel-set model was verified by dynamic simulations.

• Journal of Korean Association for Spatial Structures
• /
• v.17 no.1
• /
• pp.31-40
• /
• 2017

The objective of this study is to analysis the mechanical characteristics and nonlinear behaviors on the geometric nonlinear behavior of a cable spoke wheel roof system for long span lightweight roof structures. The weight of a cable spoke wheel roof dramatically can reduce and the cable roof system can easily make the required rigidity and shape by the sag ratio and pretension forces. Determining the pretension and initial sag of cable roof system is essential in a design process and the shape of roof is changed by pretension. The nonlinear behavior of flexible cable system has greatly an affect on the sag and pretension. This paper will be carried out analyzing and comparing the tensile forces and deflection of a cable spoke wheel system for the large span retractable roof, and analyzed to deflections and tensile forces by the post height of center hub. The double arrangement of a spoke wheel system with reverse curvature works more effectively as a load bearing system, the pretension can easily increase the structural stiffness. The cable truss system can carry vertical load in up and downward direction, and act effectively as load bearing elements.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.411-421
• /
• 2005

The development and implementation of an appropriate methodology for the accurate geometric description of track models is proposed in the framework of multibody dynamics and it includes the representation of the track spatial geometry and its irregularities. The wheel and rail surfaces are parameterized to represent any wheel and rail profiles obtained from direct measurements or design requirements. A fully generic methodology to determine, online during the dynamic simulation, the coordinates of the contact points, even when the most general three dimensional motion of the wheelset with respect to the rails is proposed. This methodology is applied to study specific issues in railway dynamics such as the flange contact problem and lead and lag contact configurations. A formulation for the description of the normal contact forces, which result from the wheel-rail interaction, is also presented. The tangential creep forces and moments that develop in the wheel-rail contact area are evaluated using : Kalker linear theory ; Heuristic force method ; Polach formulation. The methodology is implemented in a general multibody code. The discussion is supported through the application of the methodology to the railway vehicle ML95, used by the Lisbon metro company.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.12
• /
• pp.38-45
• /
• 1996

A new grinding wheel was developed for the high performance grinding of difficult-to-grinding materials. The grinding performance of the newly developed wheel including grinding forces, grinding ratio, and surface roughness of ground surface was evaluated through experiments. Experimental results show that the performance of the newly developed wheel is superior to the conventional alumina wheel and comparable to the Sol-gel wheel. An experimental investigation on the wear of alumina grinding wheel was also carried out. The experiments consist of the measurements of fracture strength of the abrasive grains, grinding force, and the area of wear flats of grinding wheels. Microscopic examination of abrasive grains was executed to observe the progress of wheel wear. The results indicate that the 32A grain, which has relatively lower fracture strength, wears out faster than 5SS and 5SG. The wheel wear occurs much faster in wet grinding than in dry grinding. It has also been found that the grinding forces increase logarithmically with increasing wear flats.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.84-91
• /
• 2012

This study evaluated three forces (lifting, pushing and twisting) required to maneuver the single-wheel barrows according to handle height, width, horizontal angle and vertical angle. The four independent variables were varied in two levels. Handle height was varies in two levels : 'knuckle height (KH)' and 'KH + 0.1 ${\times}$ stature'. The two handle widths were '1.5 ${\times}$ shoulder width (SW)' and '1.75 ${\times}$ SW'. Two angles of $0^{\circ}$ and $15^{\circ}$ were used for horizontal and vertical angles. The 24 factorial design was used in the experiment. Twelve healthy male students (undergraduate and graduate) participated in the experiment. Subjects exerted three forces (pushing, lifting, and twisting clockwise) in each experimental condition. The order of 16 treatment conditions was determined randomly. Results showed that the effects of the four factors were different according to three forces. While lifting and twisting forces were higher in 'knuckle height', the pushing force was higher in 'KH + 0.1 ${\times}$ stature' (p < 0.05). Lifting and pushing forces showed higher values in the horizontal angle $0^{\circ}$ than in $15^{\circ}$. Handle width and vertical angle showed no statistically significant main effects on three forces (p > 0.05). Results of this study could be used as basic data for the ergonomic design of handle variables of one- or two-wheel barrows.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.10
• /
• pp.118-125
• /
• 1999

In the grinding process, generally, the exciting forces with high frequency can be generated due to the wheel wear and the grinding process. As the grinding speed increases, the precise investigation about the wheel dynamic characteristics is required. Conventionally the wheel-spindle has been considered with lumped model in dynamic modeling. With this lumped model, the significant mode resulted from the shell mode of wheel can be readily ignored. This paper suggests the new analysis model which includes the shell mode of wheel in modeling the wheel-spindle assembly. Furthermore, based on the suggested model, the effects of the bolt tightening force and the taper tightening force on the dynamic properties are investigated by the finite element modal analysis and the experimental method. As a result of investigation, the shell mode vibration of wheel affects the dynamic characteristics of the spindle assembly. Also, the vibration modes of the spindle assembly are significantly affected by the joint tightening forces.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.7
• /
• pp.626-632
• /
• 2013

When a conductive rod is put within rotating axial magnet wheels arranged parallel, three-axial magnetic forces generate on the rod. In some region, the forces has a property of negative stiffness, thus they can be applied to noncontact conveyance of the rod without a control load. Apart from the passive driving, the magnet wheel should be controlled for the rod to be stayed at the still state or be moved in a specified velocity. But, because a control input is just the rotating speed of the magnet wheel, the number of input is less than that of variables to be controlled. It means that levitation force and thrust force increase at the same time for increasing wheel speed, resulting from a strong couple between two forces. Thus, in this paper, a novel method, in which the longitudinal motion of the rod is controlled indirectly by the normal motion of the rod with respect to the wheel center, is introduced to manipulate the rod without mechanical contact on space.