• Journal of the Korean Society for Railway
• /
• v.12 no.2
• /
• pp.230-235
• /
• 2009

We have conducted an experimental study to analyze characteristics of the wheel profile wear and an influence of the wheel flange wear on the vehicle's vibration characteristics. In experiment with EMU, wheel profile wear is severe at the beginning of the commercial operation. In this stage, the variations of the wheel dimension parameters and equivalent conicity is changed rapidly. Along with a mileage of the test vehicle, the wear of the wheel flange is increased and also the vibration level of the car-body is increased. The peak-peak mean value of the body vibration is estimated as good level, but the level is approached at the limit of the good level as mileage increases. Especially, the peak-peak maximum value of the body vibration shows the distinct increase of vibration level.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.561-567
• /
• 2018

This study was carried out to improve the ride quality of high-speed electric multiple unit. Through dynamic analysis of the HEMU-430X, the range of the equivalent conicity with a critical speed of 300 km/h was between 0.05 and 0.25. The initial adopted wheel profile of HEMU-430X was S1002. The equivalent conicity of S1002 with the mileage of more than 40,000 km was about 0.033 and it was confirmed that XP55 is more suitable for stable operation because XP55 has the equivalent conicity of over 0.061. In order to improve ride quality of high-speed electric multiple unit, the change of installation angle of the yaw damper was suggested from $7.35^{\circ}$ to $0^{\circ}$. From sensitivity analysis and optimization, the air spring lateral and vertical stiffness was suggested to be reduced by 30% and the secondary vertical and lateral damper damping coefficient was increased by 50%. By applying this, it was expected that the car body acceleration could be improved by about 20% on average. The HEMU-430X's yaw damper installation angle was changed to $0^{\circ}$ and the damping coefficient of the lateral damper was increased by 30%. When the test run was carried out at the speed of 300 km/h on the Kyungbu high-speed line, the vehicle lateral acceleration had improved by 34.3%. The effect of additional improvement measures proposed in this paper will be tested in the on track test. The riding quality improvement process used in this study can be used to solve ride quality problems that can occur in commercial operation of high-speed electric multiple unit in the future.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.345-350
• /
• 2005

KTX is the high speed train which is designed for 300km/h in maximum operation speed. But its long train set may cause unstable characters as swaying of the tail of a train and when the train is running on conventional line, its running safety is a point to be considered cautiously. In this study, we evaluated the running safety by the numerical analysis using VAMPIRE and compared the result with the test result of KHST, which is being in performance tests, for verifying the validity of analysis results

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.251-257
• /
• 2007

This paper describes the variation of the critical speed of an urban railway vehicle according to the change of suspension characteristics. Suspensions of a railway vehicle are composed of primary and secondary suspensions. Generally, main focus of the stability analysis has been the primary suspension. However, secondary suspension has large effects on the stability as well as the ride quality of a vehicle. In this paper, stability of an urban railway vehicle is discussed in relation to the variation of characteristics of both primary and secondary suspension. For this, modal analysis is carried out using a linear dynamic model of a half vehicle and a polynomial fit for Kalker's creep coefficients. Stability along with change of the effective conicity of a wheel is also investigated.

• Journal of the Korean Society for Railway
• /
• v.13 no.3
• /
• pp.245-250
• /
• 2010

In this work, the stability and safety analysis are carried out to predict the performance of a next generation high-speed railway vehicle (HEMU-400X). Since the safety of the high-speed railway vehicles is very important, it is meaningful to predict the dynamic performance and stability of the railway vehicles using a numerical model at a railway vehicle design step. The critical speed of the dynamic model depending on the conicity of the wheel is calculated in the stability analysis. The critical speed calculated in this analysis is over 400km/h for the conicity value of 0.15, which is determined on the basis of representative international standard, UIC 518. Also, the lateral and vertical accelerations at several points of the same dynamic model are calculated for the safety analysis. In the simulation, the dynamic model runs at the test speed of 440km/h, which is determined considering a maximum target speed, and the total driving distance is 30km. And those estimated values are less than the allowed maximum acceleration values of UIC 518.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.427-434
• /
• 2011

This paper is focused on application of recursive least squares method to estimate rail irregularities from the acceleration measurement on an axle-box or a bogie for the rail condition monitoring with in-service high-speed trains. Generally, the rail condition was monitored by a special railway inspection vehicle but the monitoring method needs an expensive measurement system. A monitoring method using accelerometers on an axle-box or a bogie was already proposed in the previous study, and the displacement was successfully estimated from the acceleration data by using Kalman and frequency selective band-pass filters. However, it was found that the displacement included not only the rail irregularities but also phase delay of the applied filters, and effect of suspension of the bogie and conicity of the wheel. To identify the rail irregularities from the estimated displacement, a compensation filter method is proposed. The compensation filters are derived by using recursive least squares method with the estimated displacement as input and the measured rail irregularity as output. The estimated rail irregularities are compared with the true rail irregularity data from the rail inspection system. From the comparison, the proposed method is a useful tool for the measurement of lateral and vertical rail irregularity.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.303-310
• /
• 2011

This paper is focused on development of models for measuring lateral and vertical track irregularities from corresponding accelerometers of an in-service high-speed train. Generally, the track irregularity was measured by a special railway inspection vehicle or system with contact or non-contact sensors. However, the sensors are very expensive and vulnerable to a harsh environment. Displacement estimation from an inertial measurement unit and its wave-band filtering was already developed in the previous study, and it was found that their results included not only the track irregularities but also other information such as phase delay of the applied filters, and suspension and conicity of the wheel. To identify the track irregularities from those results, a compensation filtering method was proposed. Each directional compensation filter was derived by using a system identification method with the estimated directional displacement as input and the corresponding track irregularities as output. In this paper, they are integrated into a model for each direction and applied to the measured lateral and vertical acceleration data from the axle-box and bogie of an in-service high-speed train. Their results are compared with the data from the track geometry measurement system. From the comparison, the proposed models are a useful tool for the measurement of the track irregularities using accelerometers of in-service high-speed trains.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.603-610
• /
• 2016

Over 12 years have passed since the first commercial operation of a Korean high-speed train. Since then, the transport capacity of the high-speed lines has become almost saturated. Therefore, studies have been carried out to increase the operating speed of the trains in order to increase their transportation capacity. This study was carried out to improve the critical speed of the KTX-Sancheon, Korean high-speed train, in order to increase its operating speed. A dynamic analysis of the KTX-Sancheon train was performed using the contact data obtained from the wheel wear profiles that were measured from a KTX-Sancheon train in commercial operation. The analysis results were verified by comparing them with the measurement acceleration data obtained from KTX-Sancheon. The suspension parameters were optimized to improve the operation speed. The critical speed of KTX-Sancheon was increased by 9.4% after the optimization by the response surface method. The optimized suspension parameters are expected to be used for the new bogie design to increase the operating speed of KTX-Sancheon from 300km/h to 350km/h.