• Restorative Dentistry and Endodontics
• /
• v.27 no.3
• /
• pp.299-309
• /
• 2002

The purposes of this study were to evaluate the microtensile bond strength of one-step adhesives accord ing to various dentin surface treatments and to observe the interface between resin(Z-100$^{TM}$) and dentin under SEM. In this study forty-five non-caries extracted human molars and three adhesive systems were used ; AlI-Bond 2(AB), One-Up Bond F(OU), AQ-Bond(AQ). ; In Group 1, 2, 3, AB was used and tooth surfaces were treated by smearing(S), ultrasonic cleansing(US), etching(E) respectively. In Group 4. 5, 6, One-Up Bond F was used and tooth surfaces were also treated as the same way above. In Groups 7, 8, 9, AQ Bond was used and tooth surfaces wet$.$e treated as the same way. Each specimen was prepared for microtensile bond testing, and were stored for 24hrs in 37$^{\circ}C$ distilled water. After that, microtensile bond strength for each specimen was measured. Specimens were fabricated to examine the failure patterns of interface between resin and dentin and observed under the SEM. The results were as follows ; 1. The results(mean$\pm$SD) of microtensile test were group 1, 25.69$\pm$4.31MPa; group 2, 40.93$\pm$10.94MPa; group 3, 47.65$\pm$8.85MPa； group 4, 35.98$\pm$9.14MPa； group 5, 39.66$\pm$8.45MPa; group 6, 43.26$\pm$13.01MPa; group 7, 25.07$\pm$4.2MPa；group 8, 30.4$\pm$4.74MPa；group 9, 33.61$\pm$7.88MPa. 2. One-Up Bond F was showed the highest value of 36.98$\pm$9.14MPa in dentin surface treatment with smearing, and there were significant differences to the other groups (p<0.05). 3. All-Bond 2 was showed the highest value of 40.93$\pm$10.94MPa in dentin surface treatment with ultra-sonic cleansing, but was no significant difference to One-Up Bond F(p>0.05) 4. All-Bond 2 was showed the highest value of 47.65$\pm$8.85MPa in dentin surface treatment with etch ing(10%phosphoric acid), and there were significant differences to the other groups(p<0.05). 5. All-Bond 2 was showed the highest value of 47.65$\pm$8.85MPa in dentin surface treatment according to manufacture's directions. but was no significant difference to One-Up Bond F(p>0.05). 6. AQ Bond was skewed the lowest microtensile bond strength with various dentin surface treatment, and the were significant differences to the other groups(p<0.05).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.19 no.6
• /
• pp.617-624
• /
• 1990

Proper processing condition of Yukwa(oil popped rice snack) for mass production and pop-ping mechanism of it were tested with Shinsun (waxy, Japonica type rice) which was excellent for Yukwa making. Optimum steaming time of dough was 15 min among 4 to 60 min and reasonable moisture content of the dough before steaming was 4895 among 48 to 53% which had good and fine texture. Acceptable stirring time of steamed dough was not significantly different among 1 to 4 min, but no stirring with much larger volume was shown very poor and too soft in texture. At the simplification test of milling method, wet milling was better then dry milling in expansion rate and high temperature treatment of dough at 6$0^{\circ}C$ gave negative effect on their quality. Extending high temperature treatment of dough, reducing sugars in the dough increased and it might be caused of starch degradation. In addition of some other protein sources to dough, Yukwa quality were in proportion to the protein content of the beans. At the long term storage of the Yukwa base, moisture absorption was different depending upon RH of atmosphere and the quality of Yukwa was inferior by storage time. By addition of some alcoholic beverage, such as Makkoli, Soju and Chungju, expansion rate and their texture were somewhat improved by increasing addition amount of them from 15% to. 30％ on dough (w/w).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.10
• /
• pp.1291-1296
• /
• 2006

This study was performed to determine the antimutagenic and anticancer effects of Fagopyrum esculentum Moenech noodles (FEMN) extracts using Ames test and cytotoxicity, respectively. FEMN made buckwheat wet noodles (BWN), buckwheat extruded noodles (BEN) and buckwheat dehydrated noodles (BDN) by 60% buckwheat flour and 70% buckwheat flour. The inhibitory effects of FEMN extracts on cell proliferation in A549, Hep3B, MCF-7, AGS and HeLa were investigated by SRB assay. The cytotoxic effects of FEMN against the cell lines with human lung carcinoma (A549), human gastric carcinoma (AGS), human hepatocellular carcinoma (Hep3B), human cervical adenocarcinoma (HeLa) and human breast adenocarcinoma (MCF-7) were inhibited with the increase of the extract concentration. The treatment of 1.0 mg/mL FEMN of 60% BEN extracts showed strong cytotoxicities of 74.7%, 75.3% and 70.5% against AGS, A549 and HeLa, respectively. The inhibition rate of 70% BWN of FEMN extracts in the S. Typhimurium TA100 strain showed 41% against the mutagenesis induced by MNNG. The inhibition rate of 70% BEN of FEMN extracts in the S. Typhimurium TA98 strain showed 45% against the mutagenesis induced by 4NQO.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.2 s.52
• /
• pp.135-145
• /
• 2007

The needs for the ultra fine particles have been increased in preparation field of raw powders such as fine ceramics and high functional products. In this study, a series of wet grinding experiments were carried out on inorganic powders such as calcite, pyrophyllite and talc by a stirred ball mill. The particle size distribution of ground products of each test material fur a given grinding time was found to be expressed by the grinding rate (selection function) which was obtained from the grinding kinetics analysis. The median diameter decreased from 6.49 to $0.47{\mu}m$ in calcite, and decreased from 3.91 to $1.14{\mu}m$ in pyrophyllite. However, in talc, median diameter was decreased a little bit from 10.30 to $6.67{\mu}m$. The grinding rate changing on calcite and pyriphyllite were similar at the same conditions. However, in the case of talc, it was observed that the grinding rate was not increased compared to other samples.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.47-47
• /
• 2011

국내의 기능성 난연성 섬유 제조기술은 원사 자체에 난연제가 포함된 상태인 난연 PET 원사나, 일반 PET 원단에 후방염 처리한 원단이 사용되기에 난연 방염성능이 만족스럽지 못하고 친환경적이지 못한 실정이다. 오늘날 세계 난연섬유 시장 규모는 10조원에 이르고 있으며 국내에서도 화재에 대한 경각심이 높아지는 추세이므로 기능성을 갖춘 고부가가치 난연소재의 개발이 시급하다. 폴리페닐렌술피드(PPS)는 내열성 및 내화학약품성이 뛰어난 열가소성 고분자로 용융방사가 가능하다. 난연성이 높은 양모섬유 또는 아크릴계 난연섬유, 아라미드 섬유 등은 비용 문제로 범용화에 한계가 있으므로 비교적 저렴한 PPS 섬유가 개발될 경우 범용화를 기대할 수 있다. 현재는 PPS 섬유가 특수한 용도에 주로 사용되고 있으나 우수한 난연 특성을 이용하여 일반 용도로의 사용 및 수요가 급격히 늘어날 것으로 예상되며 우선적으로 인테리어용 원단, 특히 커튼이나 소파용 원단으로 용도 전개가 가능할 것으로 판단하였다. 본 연구에서는 소파용 PPS 원단의 후가공 조건의 선정 및 불소계 발수방오가공을 위한 최적의 조건을 선정하고자 하였다. Padding(wet pick up율 $80{\pm}3%$)-Drying($105^{\circ}C$, 2.5min)-Curing은 시간은 1분으로 고정시킨 후, 온도를 150, 160, 170, 180, 190, $200^{\circ}C$에서 처리하여 Yellowness값을 측정한 결과, 온도가 높아질수록 Yellowness값이 커지는 것으로 미루어 보아 PPS원단은 높은 열에 영향을 받아 황변 현상이 일어나는 것으로 사료된다. 특히 $180^{\circ}C$를 기점으로 값에 큰 변화를 보였으므로 최적의 열처리 온도는 $170^{\circ}C$로 선정하여 이후의 실험을 진행하였다. 또한 큐어링 시간이 황변에 미치는 영향을 분석한 결과 온도에 의한 영향에 비해 적은 편으로 사료되었으나, 1.5min을 기점으로 Yellowess값이 높아졌으므로 최적의 열처리 시간을 1분으로 선정하였다. 최종 가공조건인 $170^{\circ}C$, 1분에서 처리한 시험포는 처리전 원단과 비교하였을 때, ${\Delta}$Yellowness가 2.84 정도로 나타났다. 그 후, PPS 원단에 불소가공제 (TG-991N, 동인텍스켐)의 적정 농도를 선정하기 위해 1~7%까지 농도를 높이며 처리한 결과, 불소가공제의 농도가 높아짐에 따라 황변현상이 나타남을 알 수 있었다. 농도가 높아짐에 따라 Yellowness값은 증가하다가 4% 이후 완만해지는 것을 알 수 있었으므로 IPA/Water Drop test와 발수도시험 (KS K 0590;2008)을 통해 적정 농도를 선정하였다. PPS 원단은 불소가공제의 농도가 높아짐에 따라 발수도가 우수해졌으며, 가공제 농도 3% 처리만으로도 우수한 발수도를 나타내었으나 100% 발수를 위해서는 가공제 농도가 5% 이상 처리되어야 하는 것을 확인할 수 있었다.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.104-114
• /
• 1992

The purpose of this study was to evaluate the shear bond strength of glass ionomer cement(Ketacfil, ESPE, Co.) against dentin surface which had been treated with surface conditioning agents(distilled water, 5% sodium hypochlorite solution, Ketac - conditioner, 40% polyacrylic acid). In this study, 60 human molars with sound and healthy crown portion which were previously extracted for orthodontic or periodontal problem. The dentin surfaces of these teeth were exposed with wet trimmer and polished with 150 - grit and 600 - grit silicon carbide paper and the teeth were divided into four groups(15 teeth per group) according to the following surface conditioning methods. Group I : Surface treatment with distilled water as control group. Group II : Surface conditioning with 5% sodium hypochlorite solution. Group III : Surface conditioning with Ketac conditioner. Group IV : Surface conditioning with 40% polyacrylic acid. The shear bond strengths were measured by Autograph(Shimatzu Co. Japan). The result of the evaluations were then subjected to statistical analysis using one - way analysis of variance and Duncan test and the results were as follows : 1. The shear bond strength accrding to the dentin surface conditioning conditions was highest in Ketac conditioner group, with measurements of $44.44{\pm}0.74(kg/cm^2)$ and lowest in the distilled water group, with measurements of $28.84{\pm}0.88(kg/cm^2)$. 2. Statistically significant differences were found between surface conditioning with 5% sodium hypochlorite solution group or Ketac conditioner group and distilled water group(P<0.01). 3. Also, statistically significant difference was found between surface conditioning with distilled water group and 40% polyacrylic acid group(P<0.05). 4. Overall difference in statistical significance between the groups was not found (P<0.05). 5. Fractured dentin surface treated with conditioning solutions showed cohesive fracture. 6. Distilled water group and 5% sodium hypochlorite solution group removed the smear layer less effectively. 7. Conditioning dentin with Ketac conditioner and 40% polyacrylic acid resulted in the removal of a significant amount of the smear layer without removing the tubular plugs and dissolving the peritubular dentin.

• Restorative Dentistry and Endodontics
• /
• v.34 no.3
• /
• pp.208-214
• /
• 2009

The purpose of this study was to compare the dye leakage of MTA (mineral trioxide aggregate) apical plug produced by two orthograde placement techniques (hand condensation technique and ultrasonically assisted hand condensation technique). To simulate straight canal, 60 transparent acrylic blocks with straight canal were fabricated. These transparent acrylic blocks were divided into 2 groups (Group C; hand condensation technique (HC) and Group U; ultrasonically assisted hand condensation technique (UAHC)) of 30 blocks with each MTA application method. Each group was divided into 2 subgroups (n=15) with different canal size of #70 (subgroup C70 and subgroup U70) and #120 (subgroup C120 and subgroup U120). After apical plug was created, a wet paper point was placed over the MTA plug and specimen was kept in a humid condition at room temperature to allow MTA to set. After 24 hours, remaining canal space was backfilled using Obtura II. All specimens were transferred to floral form socked by 0.2% rhodamine B solution and stored in 100% humidity at room temperature. After 48 hours, resin block specimens were washed and scanned using a scanner. The maximum length of micro leakage was measured from the scanned images of four surfaces of each resin block using Photoshop 6.0. Statistical analysis was performed with Mann-Whitney U test. Group U of UAHC had significantly lower leakage than Group C of HC in #70-size canal (subgroup U70) (p<0.05).

• Journal of Wetlands Research
• /
• v.15 no.3
• /
• pp.407-412
• /
• 2013

The aim of this study was to develop a tree box filter system, an example of Low Impact Development technology, for treating stormwater runoff from road. Monitoring of storm events was performed between June 2011 and November 2012 to evaluate the system performance during wet day. Based on the results, all runoff volume generated by rainfall less than 2 mm was stored in the system. The minimum volume reduction of 20% was observed in the system for rainfall greater than 20 mm. The greatest removal efficiency was exhibited by the system for total heavy metals ranging from 70 to 73% while satisfactory removal efficiency was exhibited by the system for particulate matters, organic matters and nutrients ranging from 60 to 68%. The system showed greater pollutant removal efficiency of 67 to 83% for rainfall less than 10 mm compared to rainfall greater than 10 mm which has 39 to 75% pollutant removal efficiency. The system exhibited less pollutant reduction for rainfall greater than 10 mm due to the decreased retention capacity of the system for increased rainfall. Overall, the system has proved to be an option for stormwater management that can be recommended for on-site application. Similar system may be designed based on several factors such as rainfall depth, facility size and pollutant removal efficiency.

• Korean journal of food and cookery science
• /
• v.21 no.6 s.90
• /
• pp.794-799
• /
• 2005

The overall effects of black rice wine (BRW) on black rice bread were examined through the gluten washing test, mixograph and image analysis by Cnunbscan. Commercially produced black rice flour had a much lower amount of gluten than the strong flour However, the mixture with $30\%$(flour basis) black rice flour and $70\%$ strong flour exhibited a good indication for bread making showing $30\%$ wet gluten and $14\%$ dry gluten. In the mixogram results, the peak time showed the highest value for $10\%$ added BRW, indicating an inappropriate level at $50\%$, and the changes of tail width after 8 minutes expressed that the dough became soft and sticky with increasing addition of BRW The volume of bread was increased when BRW was added, and showed the highest value at $20\%$ BRW. In relationship between the volume and bread characteristics, volume showed a highly negative relation with crumb fineness (r=-0.678) and a positive relation with crust thickness (r=0.693).

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.197-212
• /
• 1998

The purpose of this study was to evaluate the effects of fluoride application on the aspect of shear bond strength of three aesthetic restorative materials to dentin. One light-cured composite resin(Palfique Esterite) and two light-cured glass ionomer cements(Fuji II LC and Compoglass)were used in this study. 120 permanent molars were used for this study. The teeth were extracted due to the origin of periodontal disease. The crowns of all teeth were removed, and the remaining roots were embedded in epoxy resin. The mesial or distal surfaces of roots were ground flat to expose dentin and polished on wet 320-, 400-, and 600 grit SIC papers for a total of 120 prepared flat root dentin surfaces. The prepared samples were divided into six groups. Group 1, 3, and 5 were control groups and group 2, 4, and 6 were experimental groups. Sixty samples for experimental groups were treated with 2% NaF solution for 5 minutes. Group 1 and 2 were bonded with Plafique Esterite, group 3 and 4 were bonded with Fuji II LC, and group 5 and 6 were bonded with Compoglass. After 24 hours water storage at $37{\pm}1^{\circ}C$, all samples were subjected to a shear to fracture with Instron universal testing machine(No.4467) at 1.0 mm/min displacement rate. Dentin surfaces treated with each conditioners before bonding and interfacial layers between dentin and aesthetic restorative materials were observed under Scanning Electron Microscope(Hitachi S-2300) at 20Kvp. The data were evaluated statistically at the 95% confidence level with ANOVA test. The result were as follows; 1. Among the control groups, group 1 showed strongest bond strength and group 3 showed weakest. 2. Among the experimental groups, group 2 showed strongest bond strength and group 6 showed weakest. 3. Statistical analysis of the data showed that pretreatment of dentin with 2% NaF solution significantly decreased the bond strength of three aesthetic restorative materials to dentin(P<0.05). 4. SEM findings of fluoride treated dentin surfaces (2, 4, 6 group) demonstrated dentin surfaces covered with fluoridated reaction products. 5. Except group 4 and 6, resin tags were formed in all groups.