• 한국세라믹학회지
• /
• 제34권11호
• /
• pp.1107-1112
• /
• 1997

Mn-Zn ferrite powders prepared by an alcoholic dehydration method. Vacuum casting, a kind of wet forming process was examined with this powders. As binders, polyethylene glycol and polyvinyl alcohol were used. In order to estimate this conditions, fracture morphology, densities of green and sintered bodies and the microstructure were observed. High density and homogeneous microstructure in sintered bodies were obtained in the case of 0.1 wt% PEG or 0.5 wt% PVA.

• 마이크로전자및패키징학회지
• /
• 제19권4호
• /
• pp.51-56
• /
• 2012

습식공정으로 thermal via용 SI 관통 via를 형성하기 위해 TMAH 용액의 농도와 온도에 따른 Si 기판의 이방성 습식식각 거동을 분석하였다. TMAH 용액의 온도를 $80^{\circ}C$로 유지한 경우, 5 wt%, 10 wt% 및 25 wt% 농도의 TMAH 용액은 각기 $0.76{\mu}m/min$, $0.75{\mu}m/min$ 및 $0.30{\mu}m/min$의 Si 식각속도를 나타내었다. 10 wt% TMAH 용액의 온도를 $20^{\circ}C$와 $50^{\circ}C$로 유지시에는 각기 $0.07{\mu}m/min$와 $0.23{\mu}m/min$으로 식각속도가 저하하였다. Si 기판의 양면에 동일한 형태의 식각 패턴을 형성하여 $80^{\circ}C$의 10 wt% TMAH 용액에 장입하고 5시간 식각하여 깊이 $500{\mu}m$의 관통 via hole을 형성하였다.

• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.13-17
• /
• 2016

It is highlighted that increasing the adsorbent surface area on volumetric basis is very important in providing an easy access for gas molecules. Fine particles around $3{\mu}m$ of soft-burned dolomite kiln dust (SB-DKD) were hydrated to wet slurry samples by ball mill process and then placed in a chamber to use spray dryer method. Spherical granules with particle size distribution of $50{\sim}60{\mu}m$ were prepared under the experimental condition with or without addition of a pore-forming agent. The relationship between bead size of the pore-forming agent and size of SB-DKD particles is the most significant factor in preparation of spherical granules with a high porosity. Whereas addition of smaller beads than SB-DKD resulted in almost no change in the surface porosity of spherical granules, addition of larger beads than SB-DKD contributed to obtaining of the particles with both 15 times larger average pore volume and 1 order of magnitude larger porosity. It is considered that spherical granules with improved $N_2$ gas adsorption ability may also be utilized for other atmospheric gas adsorption.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2003년도 The 4th Korea-Italy Workshop
• /
• pp.133-135
• /
• 2003

The removal of dissolved oxygen(DO) from water was studied using a poly(vinyliene fluoride)(PVDF) hollow fiber membrane contactor(HFMC) with the vacuum degassing process(VDP), Asymmetric porous PVDF hollow fiber membranes (HFM) for membrane contactor were prepared by a wet phase inversion method. In spinning of these PVDF hollow fibers, dimethy lacetamide (DMAc), LiCl and pure water were used as a solvent, a pore-forming additive and internal/external coagulant, respectively. The characteristics of the structure(pore size, porosity etc.) of the prepared PVDF HFMs as a function of concentration of pore-forming additive in polymer dope solution were studied. Also, the removal efficiency of DO from water according to flow rates of water, using PVDF HFMC with VDP, was studied. The performance of the asymmetric porous PVDF HFMC and a symmetric porous PP HFMC commercialized were compared. As a result, the asymmetric porous PVDF HFMC showed higher removal efficiency of DO than that of a symmetric porous PP HFMC.

• 한국정보통신학회논문지
• /
• 제13권7호
• /
• pp.1393-1398
• /
• 2009

본 연구는 LCD용 비정질 실리콘박막트랜지스터의 제조공정중 가장 중요한 식각 공정에서 각 박막의 특성에 맞는 습식 및 건식식각공정을 개발하여 소자의 특성을 안정시키고자 한다. 본 연구의 수소화 된 비정질 실리콘 박막 트랜지스터는 Inverted Staggered 형태로 게이트 전극이 하부에 있다. 실험 방법은 게이트전극, 절연층, 전도층, 에치스토퍼 및 포토레지스터층을 연속 증착한다. 스토퍼층을 게이트 전극의 패턴으로 남기고, 그 위에 n+a-Si:H 층 및 NPR(Negative Photo Resister)을 형성시킨다. 상부 게이트 전극과 반대의 패턴으로 NPR층을 패터닝하여 그것을 마스크로 상부 n+a-Si:H 층을 식각하고, 남아있는 NPR층을 제거 한다. 그 위 에 Cr층을 증착한 후 패터닝 하여 소오스-드레인 전극을 위한 Cr층을 형성시켜 박막 트랜지스터를 제조한다. 여기서 각 박막의 패터닝은 식각 공정으로 각단위 박막의 특성에 맞는 건식 및 습식식각 공정이 필요하다. 제조한 박막 트랜지스터에서 가장 흔히 발생되는 문제는 주로 식각 공정시 over 및 under etching 이며, 정확한 식각을 위하여 각 박막에 맞는 식각공정을 개발하여 소자의 최적 특성을 제공하고자한다. 이와 같이 공정에 보다 엄격한 기준의 건식 및 습식식각 공정 그리고 세척 등의 처리공정을 정밀하게 실시하여 소자의 특성을 확실히 개선 할 수 있었다.

• 펄프종이기술
• /
• 제46권5호
• /
• pp.61-68
• /
• 2014

The energy efficiency of papermaking process becomes more significant because of various new regulation of the energy consumption and the green house gas emission. In this study, the effects of wood powder addition on the drainage and the drying efficiency of the OCC based paper products, linerboard, were deeply investigated for improving energy efficiency. The fractionation of wood powder depending on the size were conducted. The bigger size of wood powder resulted in the higher bulk and the higher drainage efficiency, but the lower paper strength. The drying efficiency were in detail evaluated depending on the drying process level. In the first section of drying process until the 80% solid level, there were no significant changes in the drying efficiency by the addition of wood powder. However, after the 80 % solid level, the drying efficiency was greatly improved by the addition of wood powder. Those results showed the addition of wood powder could greatly affect not only the drainage in forming and wet pressing but also the drying process.

• Corrosion Science and Technology
• /
• 제7권2호
• /
• pp.119-124
• /
• 2008

Steel is generally not corrosion resistant to water with formation of non protective rusts on its surface. Rusts are composed of iron oxides such as $Fe_3O_4$, $\alpha-$, $\beta-$, $\gamma-$and ${\delta}-FeOOH$. However, steel, particularly weathering steel containing small amounts of Cu, Ni and Cr etc., shows good corrosion resistance against rural, industrial or marine environment. Its corrosion rate is exceedingly small as compared with that of carbon steel. According to the exposure test results undertaken in outdoor environments, the atmospheric corrosion rate for weathering steel is only 1 mm for a century. Atmospheric corrosion for steels proceeds under alternate dry and wet conditions. Dry condition is encountered on steel surface on fine or cloudy days, and wet condition is on rainy or snowy days. The reason why weathering steel shows superior atmospheric corrosion resistance is due to formation of corrosion protective rusts on its surface under very thin water layer. The protective rusts are usually composed of two layer rusts; the upper layer is ${\gamma}-FeOOH$ termed as lepidocrocite, and inner layer is nano-particle ${\alpha}-FeOOH$ termed as goethite. This paper is aimed at elucidating the atmospheric corrosion mechanism for steel in comparison with corrosion in bulky water environment by use of empirical data.The summary is as follows: 1. No corrosion protective rusts are formed on steel in bulky water. 2. Atmospheric corrosion for steel is the corrosion under wetting and drying conditions. Corrosion and passivation occur alternately on steel surface. Steel, particularly weathering steel with small amounts of alloying elements such as Cu, Ni and Cr etc. enhances forming corrosion protective rusts by passivation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.448-451
• /
• 2003

This study describes a new maskless nano-fabrication technique of Si (100) using the combination of nanometer-scale mechanical forming by nano-indenter XP and KOH wet etching. First the surface of a Si (100) specimen was machined by using the nano-machining system, which utilizes the mechanism of the nano-indenter XP. Next, the specimen was etched by KOH solution. After the etching process, the convex structure or deeper hole is made because of masking or promotion effect of the affected layer generated by nano-machining. On the basis of this interesting fact, some sample structures were fabricated.

• 펄프종이기술
• /
• 제31권1호
• /
• pp.52-60
• /
• 1999

Drainage rate in wet-end, which has significant influences on the production capacity, product quality and process economics in papermaking, becomes an important factor in the modern high speed papermaking processes owing to increased level of fines contained in today's pulp materials and increased papermaking system closure. A study was carred out to investigate the influence of beating and fines content on natural and vacuum dewatering using a vacuum drainage tester. Increase in beating and accumulation of fines in the stock decreased natural dewatering, Vacuum dewatering effect, however, increased substantially as beating and fines content were increased. But this increase in vacuum dewatering decreased again when a stock is severely beaten or fines content is greater than 35%. Above this level of fines content, mobile fines migrates to the interstices of the forming web to cause sealing or plugging which restrict fluid movement through the web.

• 한국재료학회지
• /
• 제28권4호
• /
• pp.201-207
• /
• 2018

Infrared(IR) heating has many advantages, such as energy efficiency, reduced heating time, cleanliness, equipment compactness, high drying rate and easy automation. These features of IR heating provide widely industrial applications, such as surface heat treatment in semiconductor fabrication, thermoforming of polymers, drying and disinfection of food products, heating to metal forging, and drying of wet materials. In this study, the characteristics of a protected gold mirror were examined by spectrophotometer and the lifetime of the coating layers were evaluated by a cross-cutting method and salt spray test. The effects of manufacturing conditions on the protected gold mirror were seen and remedies for these effects were noted in order to improve the properties of the protected gold mirror in the drying process. The reflectance and lifetime of the protected gold mirror was influenced by manufacturing conditions, such as surface roughness and forming conditions of the anti-oxide layer, the adhesion layer, the reflecting layer and the protection layer. The results of this study showed that the protected gold mirror manufactured using a buffing method for pre-treatment resulted in the most effective reflectance. In addition, $Al_2O_3$ coating on an Al substrate as an anti-oxide layer was more effective than the anodizing process in the test of reflectance. Furthermore, the protected gold mirror manufactured by layers forming of various materials resulted in the most effective reflectance and lifetime when coated with $Al_2O_3$ as the anti-oxide layer, coated Cr as the adhesion layer, and coated $MgF_2$ as the protection layer.