• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.953-956
• /
• 1996

The main regularities of the process of strain of the leafstalk boimass of the annual and parennial sown grasses (hard phase) with the simulataneous filtration of the vegetable juice (liquid phase) in the working members of the uninterrupted action(screw press) and the periodic action (Briqueting stamp press) were established . The engineering methods of calculation of the basic constructive -technological parameter of the pres equipment of the given types were worked out.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.2
• /
• pp.109-113
• /
• 2011

Hot air flow simulations of the wet station dryer module for the solar cell cleaning were conducted. Air incident angles such as to the substrates ($45^{\circ}$), to the bottom ($90^{\circ}$), and to the wall ($135^{\circ}$) were considered. Based on the simulated velocity and temperature profiles, appropriate incident angle was proposed, and it was well matched to experimental results. Additionally, uniform and non-uniform air hole sizes of the tube were compared for the uniform air flow distribution through the batch.

• Tunnel and Underground Space
• /
• v.32 no.6
• /
• pp.353-362
• /
• 2022

The wet shotcrete refers to a method in which all materials are mixed and then supplied to the spraying device, compressed air is added to the nozzle, and the spraying speed is improved to spray on the target surface. In order to reproduce the amount of shotcrete used in the wet method in the field and the situation at the laboratory scale, it is essential to control the discharge amount of the equipment. In this study, in order to increase the reproducibility of field conditions at the laboratory scale, a flow control system for shotcrete mortar spraying equipment was developed and applied to the equipment. To verify the developed equipment, a discharge control test using water and mortar was performed. In the developed control system, the discharge was smoothly controlled according to the user input value for the mono pump, but the discharge was not properly controlled according to the input value for the screw pump because of a reducer. When a speed reducer is attached, it is necessary to adjust the operation rate of the screw pump close to the target flow rate by increasing the operation rate of the screw pump while lowering the operation rate of the mono pump.

• Journal of the Korean Institute of Gas
• /
• v.27 no.4
• /
• pp.1-11
• /
• 2023

The size of the OLED material market is expected to grow from $1.1 billion in 2019 to $2.3 billion in 2023, with an average annual sustainable growth of more than 19%. Among the facilities mainly used by OLED material manufacturers, accidents such as fire, explosion, and leakage frequently occur when using filtration equipment, so it is necessary to improve the risk when using filtration equipment. In this study, it was divided into four main processes, namely, assembly and disassembly process, filtration process, wet cake recovery process, and washing process in order to derive the risks associated with the use of filtration equipment. Hazard factors were derived by conducting accident case investigations, preliminary interviews, and surveys. For the analysis of questionnaire results, statistical analysis such as frequency analysis and Pearson chi-square test analysis was performed using SPSS 21, and risk improvement measures were suggested using the analyzed results. It is expected that this study will serve as a basis for dealing with safety and risk factors that may occur as the size of the OLED market expands.

• Journal of Ecology and Environment
• /
• v.38 no.3
• /
• pp.293-305
• /
• 2015

In order to understand the mechanisms of conversion between different algal dominance, an experiment was performed in a greenhouse from 22 June to 10 July 2011. The experiment included a treatment group subjected to three instances of nutrient enrichment and a control with no nutrient enrichment. The initial water was dominated by Ankistrodesmus of Chlorophyta. The average water temperature at 08:30 h and 14:00 h during the experiment was $31.6^{\circ}C$ and $34.6^{\circ}C$, respectively. The results showed that the total nitrogen (TN), total phosphorus (TP), dissolved total nitrogen (DTN), dissolved total phosphorus (DTP), and soluble reactive phosphorus (SRP) concentrations in the treatment were significantly higher than in the control (P < 0.05). However, the TN/TP and DTN/DTP in the control was higher than in the treatment (P < 0.05). The dominant algae in the control did not change during the experiment, while the dominant algae in the treatment switched to Planktothrix of Cyanophyta on day 9. The chlorophyll a (Chl-a), wet weight of all algae, wet weight of Cyanophyta, and percentage of Cyanophyta in the control were all significantly lower than in the treatment (P < 0.05). Amounts of zooplankton, especially rotifers, were present at the end of the experimental period. The density of rotifers between the control and treatment was not significantly different (P > 0.05), while the copepod density in the treatment was higher than in the control (P < 0.05). We conclude that green algae dominance quickly switches to cyanobacteria dominance after nutrient enrichment in a greenhouse with elevated temperature.

• Corrosion Science and Technology
• /
• v.16 no.2
• /
• pp.76-84
• /
• 2017

In the construction of subsea oil and gas developments, it is increasingly common that subsea oil and gas equipment will be installed in subsea well before final hookup and production. Installation of wellheads, subsea hardware, pipelines, and surface facilities (platforms, FPSO, FLNG, connected terminals, or gas plants) are increasingly driven by independent cost and vessel availability schedules; this gives rise to requirements that the subsea facilities must be stored in the seabed for a specific time. In addition, schedule delays, particularly in the installation or startup of the connected platform, FPSO, FLNG, or onshore plant may cause unexpected extensions of the intended storage period. Currently, there are two methods commonly used for storage subsea facilities in the seabed: dry parking and wet parking. Each method has its own risks, challenges, and implications for the facility life and its integrity. The corrosion management and preservation method selection is a crucial factor to be considered in choosing the appropriate storage method and achieving a successful seabed storage. An overview of those factors is presented, along with a discussion on the internal corrosion threats and assessments.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.179-190
• /
• 2003

The grout based on solution type makes it difficult to get the improvement of ground strength and the effefct of water curtain because it has lower strength and durability than suspension type. Nowadays, the technology of particle acceleration, that enhance the material permeability, such as grout based on solution type, and inexpensive grout, is being required. For these reasons, in this study, using wet milling system, we evaluated physical properties of manufactured factors such as water-cement ratio of particles before being milled, optimum milling capacity by controlling milling time and rpm, viscosity of materials, permeation coefficient, and unconfined compressive strength. Also, using micro wet milling apparatus which could manufacture ordinary Portland cement and high speed shear mix which could forcefully separate conglomerate particles in situ, we performed electrical resistivity investigation and falling head permeability tests to analyze differences of grouting effects. From these results, we found that the permeability of the applied equipment was much superior, and in the case of using high speed shear mixer, particles of grout material were well separated.

• International Journal of Highway Engineering
• /
• v.20 no.1
• /
• pp.77-85
• /
• 2018

PURPOSES : The purpose of this study was to develop an urgent road-repair system and perform a field applicability test, as well as discover the optimum mix design for machine applications compared to the optimum mix design for lab applications. METHODS : According to reviews of the patent and developed equipment, self-propelled and mix-in-place equipment types are suitable for urgent pavement repair, e.g., potholes and cracks. The machine-application mix design was revised based on the optimum lab-test mix design, and the field application of a spray-injection system was performed on the job site. The mixture from the machine application and lab application was subjected to a wet-track abrasion test and a wheel-tracking test to calibrate the machine application. RESULTS and CONCLUSIONS : This study showed that the binder content could differ for the lab application and the machine application in the same setting. Based on the wet-track abrasion test result, the binder contents of the machine application exceeded the binder contents of the lab application by 1-1.5% on the same setting value. Moreover, the maximum dynamic stability value for the machine application showed 1% lower binder contents than the maximum lab-application value. Collectively, the results of the two different tests showed that the different sizes and operating methods of the machine and lab applications could affect the mix designs. Further studies will be performed to verify the bonding strength and monitor the field application.

• Journal of the Korean Vacuum Society
• /
• v.18 no.5
• /
• pp.337-345
• /
• 2009

When the drill hole diameter for the package substrate is under $100{\mu}m$, the smear in the drill hole cannot be eliminated by wet desmear process only. We intended to change the substrate's hydrophobic characteristics to hydrophilic characteristics by adapting the atmospheric pressure plasma prior to the wet desmear process. Atmospheric pressure plasma process was made as the inline type equipment which is adequate for the package substrate's manufacturing process and remote DBD type electrodes were used for the equipment. As the result of atmospheric pressure plasma processing, the contact angle of the substrate was enhanced from 71 degree to 30 degree. Dielectric film thickness, drill hole diameter and surface roughness were measured to evaluated the characteristics of the wet desmear process in case of plasma processing and in case of none. By the measurement, it was analyzed that the process uniformity within the whole panel was largely enhanced. Also, it was verified that the smear in the drill hole was eliminated efficiently which was analyzed by the SEM image of the drill hole.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.256-262
• /
• 2015

This study has an innovative improvement of the ocher tiles production system that aims to resolve social issue of industrial waste and to meet the customer needs for environmental-friendly building materials. By changing a wet type cutting method to a dry type of ocher tiles production system, the three processes such as cleaning, dehydration, and drying can be removed in existing overall process of 17 steps. Accordingly, the application of the wet type cutting method, which is proposed in this study, makes an increase in ocher tiles production from 1,500 to 1,850 pieces per hour. In particular, industrial wastewater that was emerging as the biggest problem in environmental pollutants in the wet cutting method has been removed. In addition, the most serious problems of noise and dust from the operator side, while developing a device for the dry cutting method, are eliminated through the development of additional equipment.