• 한국전기전자재료학회논문지
• /
• 제21권2호
• /
• pp.111-117
• /
• 2008

We have studied surface roughness, contamination of impurity, bonding with some gas element, reflectance and zeta potential on masks to be generated or changed during photolithography/dry or wet etching process. Mask surface roughness was not changed after photolithography/dry etching process. But surface roughness was changed on some area under MoSi film of Cr/MoSi/Qz. There was not detected any impurity on mask surface after plasma dry etching process. Reflectance of mask was increased after variable plasma etching treatment, especially when mask was treated with plasma including $O_2$ gas. Blank mask was positively charged when the mask was treated with Cr plasma etching gas($Cl_2:250$ sccm/He:20 $sccm/O_2:29$ seem, source power:100 W/bias power:20 W, 300 sec). But this positive charge was changed to negative charge when the mask was treated with $CF_4$ gas for MoSi plasma etching, resulting better wet cleaning. There was appeared with negative charge on MoSi/Qz mask treated with Cr plasma etching process condition, and this mask was measured with more negative after SC-1 wet cleaning process, resulting better wet cleaning. This mask was charged with positive after treatment with $O_2$ plasma again, resulting bad wet cleaning condition.

• 설비공학논문집
• /
• 제27권9호
• /
• pp.475-483
• /
• 2015

In Korea, a typically hot and humid summer means that air-conditioners consume a large quantity of electricity; accordingly, the simultaneous usage of an indirect evaporative cooler may reduce the sensible-heat level and save the amount of electricity that is consumed. In this study, the heat-transfer and pressure-drop characteristics of an indirect evaporative cooler made of paper/plastic film were investigated under both dry and wet conditions; for the purpose of comparison, an indirect evaporative cooler made of plastic film was also tested. Our results show that the indirect evaporative efficiencies under a wet condition are greater than those under a dry condition, and the efficiencies of the paper/plastic sample (109% to 138%) are greater than those (67% to 89%) of the plastic sample; in addition, the wet-surface, indirect evaporative efficiencies of the paper/plastic sample are 32% to 36% greater than those of the plastic sample. Further, the wet-surface pressure drops of the paper/plastic sample are 13% to 23% larger than those of the plastic sample, and this might have been caused by the surface roughness of the samples. A rigorous heat-transfer analysis revealed that, for the plastic sample, 30% to 37% of the wet channels remained dry, whereas all of the channels were wet for the paper/plastic sample.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2005년도 추계학술대회 학술발표 논문집 제15권 제2호
• /
• pp.471-474
• /
• 2005

객관적이고, 과학적인 수사를 위해, 교통사고는 공정한 기록에 의해서, 컴퓨터 모의실험, 및 학문, 그리고 충돌 사고 역동성, 도로 및 교통 공학으로 검증되어야 한다. 본 논문에서는, 교통사고, 과학, 객관적인 방법을 이용하여 진짜 교통사고 및 결과를 재현한다. 본 논문에서는 모의실험 결과 다음 같은 사항이 입증되었다. 습한 도로 조건에서 브레이크 작동시간이 건조한 도로 상태보다 더 긴 것이 입증되었다. 뿐만 아니라, 포장도로와 비포장 돌에서는 비포장도로의 제동시간이 포장도로의 제동시간 보다 짧다는 것이 입증되었다.

• 한국안전학회지
• /
• 제5권1호
• /
• pp.31-39
• /
• 1990

In this paper, the influence of the table speed, metal removal rate and grinding fluid on long wheel workpiece contact zone at high effect grinding was investigated by theoretical analyses and measuring the temperature, and discussed by the temperature distribution in grinding surface layer. Main results obtained are as follows, 1) Rega.dless of the table speed, the temperature gap of the workpiece(heat influx) is about 6-8 times as high in dry condition as in wet condition. 2) Good grinding condition can be obtained owing to the effect of grinding fluid without any burning defect under the condition of the metal removal rate(1.0mm$^3$/mm.s) in case of wet grinding. 3) When the depth from the surface layer is about 1.25-1.5mm under the condition of the slow table speed, surface temperature goes up higher as the table speed slows down, because long contact time is laked at the surface layer. 4) In case of the same metal removal rate, the lower the table speed becomes, the higher the surface temperature is, because grinding depth has a far more influence on wheel workpiece contact zone than the table speed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.695-702
• /
• 2002

Shotcrete (or Sprayed concrete) has been used as an important support material in New Austrian Tunnelling Method (NATM). Since the mid of 1990, permanent shotcrete tunnel linings such as Single-shell, NMT (Norwegian Method of Tunnelling) has been constructed in many countries for reducing the construction time and lowing construction costs instead of conventional in-situ concrete linings. Among essential technologies for successful application of permanent shotcrcte linings, high performance shotcrete providing high strength, high durability, better pumpability has to be developed in advance as an integral component. This paper presents the Ideas and first experimental attempts to increase early strength and bond strength of wet-mixed Steel Fiber Reinforced Shotcrete(SFRS) in sump water condition. In order to increase early strength, a new approach using high-early strength cement with liquid alkali-free accelerator has been investigated From the results, wet-mix SFRS with high-early strength cement and alkali-free accelerator exhibited excellent early strength improvement compared to the ordinary portland content and good bond strength even under sump water condition.

• 한국농공학회지
• /
• 제45권6호
• /
• pp.153-161
• /
• 2003

The purpose of this paper is to investigate the soil-water characteristic curves for an unsaturated soil. To this ends, a series of suction measured test was conducted on the selected 4 kinds of soils taken from different sites of Korea, using modified pressure plate apparatus. Form the test results, the water contents, degree of saturation and volumetric water contents were analyzed with the suction. And the soil-water characteristic curves of unsaturated soil were drawn from the test results for various factors. The characteristic curves drawn with water content vs matric suction were classified certainly the difference in wet side but were not classified in dry side. The characteristic curves drawn with degree of saturation vs matric suction for unsaturated soil were shown the opposite inclination as compared with the former curve. But the characteristic curve with volumetric water content vs matric suction was described suitably not only in wet side condition but also in dry side. And it was found that the volumetric water contents of loose soil was high at the initial condition but that of dense soil was high at final condition (dry side).

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2005년도 추계학술발표논문집
• /
• pp.259-263
• /
• 2005

This study was performed to introduce recently developed Polyvinylamine as a wet-end process improving aids and paper properties improving aids. As a retention and drainage aids, cationicity of Polyvinylamine was a very important factor of BCTMP and ONP stock condition. As a dry tensile strength aids, The hydrogen bond of acrylamide functionality and hydroxyl functionality of the pulp was a very important factor of LBKP stock condition and cationicity of Polyvinylamine was a very important factor of BCTMP and ONP stock condition.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.85-90
• /
• 2012

Wet pressing process has great influence not only on the paper properties but also on the efficiency of total manufacturing process including energy efficiency. The slow drainage propensity of old corrugated container(OCC) might require more complicated control of wet pressing process. In this study, the change in press efficiency and in structure of wet sheet by the various condition of laboratory roll press simulator were evaluated to provide background information about wet pressing of OCC. The higher pressure and the slower machine speed resulted in higher efficiency of wet pressing but the change trends of dryness depending on the wet press pressure and machine speed were shown differently according to OCC treatment. The effects of water contents of felt on the wet press efficiency and sheet structure were also investigated. The higher contents of water in felt resulted in less removal of water generally and the crushed structure of wet sheet were appeared especially at higher pressure.

• 한국해양공학회지
• /
• 제15권4호
• /
• pp.73-79
• /
• 2001

Underwater wet bead-on-plate welds were experimentally performed on 11mm thick SS400 steel plate as base metal by using six different types of flux coated electrodes of 3.2mm diameter. Two kinds of different flux coated wet arc electrodes (UW-1, UW-2) were individually designed flux materials, three kinds of the electrodes (E4301, E4311, E4313) were terrestrial electrodes and the another one (TN20) was an imported underwater wet welding electrode. As results, the individually designed flux coated underwater electrode, UW-2 and TN20 had a good starting and the excellent arc stability compared with other electrodes. No significant difference of bead appearance could be detected, but the slag detachability of TN20 electrodes was relatively undesirable. By rapid cooling rate, the hardness value and the portion of martensite of HAZ were increased, but it was considerably maintain stable for TN20 and UW-2 electrodes. The individually designed flux coated electrode, UW-2 could be used in practice for underwater bead welds.

• 한국정보통신학회논문지
• /
• 제14권6호
• /
• pp.1465-1468
• /
• 2010

습식 식각은 식각용액으로서 화학용액을 사용하는 공정으로 반응물이 기판표면에서 화학반응을 일으켜 표면을 식각하는 과정이다. 습식 식각 시 수${\mu}m$의 해상도를 얻기 위해서는 그 부식액의 조성이나, 에칭시간, 부식액의 온도 등을 고려하여야 한다. 본 실험에서 사용한 금속은 Cr, Al, ITO 로 모두 DC sputter 방법을 사용해서 증착하여 사용하였다. Cr박막은 $1300{\AA}$ 정도의 두께를 사용하였고, ITO (Indium Tin Oxide) 박막은 가시광 영역에서 투명하고 (80% 이상의 transmittance), 저저항 (Sheet Resistance : $50\;{\Omega}/sq$ 이하) 인 박막을 사용하였으며, 신호선으로 주로 사용되는 Al등의 증착조건에 따른 wet etching 특성을 조사하였다.