• 한국표면공학회지
• /
• 제28권5호
• /
• pp.289-299
• /
• 1995

The effects of phosphate coating have been studied on physical properties and corrosion resistance of painted aluminum alloy sheet for automobile body. The physical properties (surface roughness, paint adhesion, impact resistance and pencil hardness) and corrosion resistance(cyclic corrosion and filiform corrosion) were investigated. Phosphate coatings enhanced the physical properties of painted Al alloy sheet, especially paint adhesion after the 240hours water immersion test. Phosphate coating also markedly improved the resistance for cyclic corrosion and filiform corrosion of painted cold rolled steel and Zn-Ni plated steel sheet as well as painted Al alloy sheet. The corrosion resistance of painted Al sheets was varied with the concentration of free fluoride ion and metal additives like Ni and Mn in the phosphating bath. A maximum corrosion resistance was obtained at about 300ppm of fluoride ion and additives of Ni and Mn obviously increased the corrosion resistance of painted specimens.

• Journal of Magnetics
• /
• 제17권4호
• /
• pp.280-284
• /
• 2012

This paper presents a method for evaluating interior permanent magnet synchronous motor (IPMSM) performance over the entire operation region. Using a d-q axis equivalent circuit model consisting of motor parameters such as the permanent magnetic flux, copper resistance, core loss resistance, and d-q axis inductance, a conventional mathematical model of an IPMSM has been developed. It is well understood that in IPMSMs, magnetic operating conditions cause cross saturation and that the iron loss resistance - upon which core losses depend - changes according to the motor speed; for the sake of convenience, however, d-q axis machine models usually neglect the influence of magnetic cross saturation and assume that the iron loss resistance is constant. This paper proposes an analysis method based on considering a magnetic cross saturation and estimating a core loss resistance that changes with the operating conditions and speed. The proposed method is then verified by means of a comparison between the computed and the experimental results.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1231-1236
• /
• 1996

The electrode resistance of semiconducting PTC BaTiO3 ceramic material was studied in some detail. Comme-rical In-Ag paste In-Ga alloy and electroless plated Ni as well as evaporated Al were chosen as electrode. The contact resistance of electroded samples were measured by both dc resistivity and ac impedance analysis. The aging effect on contact resistance under cyclic loading from -1$0^{\circ}C$ to 85$^{\circ}C$ was also monitored for the prolonged period of time. In case of Al electroded samples the heat treatment and protective coating had effects on the stability against contact resistance degradation. It was also found that the samples with commercial In-Ag paste and electroless plated Ni electrode had good properties of contact resistance against aging.

• Journal of Microbiology
• /
• 제45권1호
• /
• pp.64-68
• /
• 2007

In this study we examined the multi-drug resistance profiles of the tetracycline (TC) resistant genus Vibrio to determine its susceptibility to two ${\beta}-lactams$, ampicillin (ABPC), and mecillinam (MPC), as well as to macrolide, erythromycin (EM). The results showed various patterns of resistance among strains that were isolated from very close geographical areas during the same year, suggesting diverse patterns of drug resistance in environmental bacteria from this area. In addition, the cross-resistance patterns suggested that the resistance determinants among Vibrio spp. are acquired differently within the sediment and seawater environments.

• Biomolecules & Therapeutics
• /
• 제20권3호
• /
• pp.256-267
• /
• 2012

Tamoxifen is a central component of the treatment of estrogen receptor (ER)-positive breast cancer as a partial agonist of ER. It has been clinically used for the last 30 years and is currently available as a chemopreventive agent in women with high risk for breast cancer. The most challenging issue with tamoxifen use is the development of resistance in an initially responsive breast tumor. This review summarizes the roles of ER as the therapeutic target of tamoxifen in cancer treatment, clinical values and issues of tamoxifen use, and molecular mechanisms of tamoxifen resistance. Emerging knowledge on the molecular mechanisms of tamoxifen resistance will provide insight into the design of regimens to overcome tamoxifen resistance and discovery of novel therapeutic agents with a decreased chance of developing resistance as well as establishing more efficient treatment strategies.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권3호
• /
• pp.626-639
• /
• 2015

Ice resistance is defined as the time average of all longitudinal forces due to ice acting on the ship. Estimation of ship's resistance in ice-covered waters is very important to both designers and shipbuilders since it is closely related to propulsion of a ship and it determines the engine power of the ship. Good ice performance requires ice resistance should be as low as possible to allow different manoeuvres. In this paper, different numerical methods are presented to calculate ice resistance, including semi-analytical method and empirical methods. A model test of an icebreaking vessel that was done in an ice basin has been introduced for going straight ahead in level ice at low speed. Then the comparison between model test results and numerical results are made. Some discussions and suggestions are presented as well to provide an insight into icebreaking vessel design at early stage.

• 대한토목학회논문집
• /
• 제31권6C호
• /
• pp.259-266
• /
• 2011

기초구조물의 신뢰성 있는 저항계수 산정을 위해서는 충분한 양의 재하시험 결과에 근거한 저항의 분포특성 분석이 선행되어야 한다. 본 연구에서는 베이지안 이론에 근거하여 검증용 정재하시험 결과를 저항의 분포특성 분석에 반영할 수 있는 개선된 해석법을 제안하였고, 이를 통해 기 제안된 국내 타입강관말뚝의 저항계수를 갱신하였다. 측정 지지력이 확인된 정재하시험 결과를 이용하여 저항의 사전 분포특성을 산정하고, 검증용 정재하시험 결과를 우도정보로 고려하여 저항의 사후 분포특성을 평가하였다. 갱신된 저항의 사후 분포특성을 이용하여 일차신뢰도법에 의해 저항계수를 산정하였다. 총 5회의 검증용 재하시험 결과를 반영할 경우, 갱신된 저항계수는 목표신뢰도지수 2.33, 3.0에 대하여 각각 0.27-0.96, 0.19-0.68의 범위를 나타내었다. 본 연구에서 제시된 해석법을 통해 양질의 측정지지력 데이터가 부족하여 신뢰성 있는 저항계수를 산정하기 어려운 경우 현장 검증시험 결과를 반영한 저항계수의 보정이 가능함을 확인하였다.

• 지식경영연구
• /
• 제16권4호
• /
• pp.191-213
• /
• 2015

With the advancement of virtual reality technology, virtual reality contents and devices are being competitively released. This research deals with an early stage adoption model of a motion-sensing input device which enhances the user experience of these virtual reality contents and devices. In contrast to the previous research on the adoption or resistance of innovative products, this work compares and analyzes the antecedents in MIR(Model of Innovation Resistance) of resistance-perspective as well as those in UTAUT2(Extended Unified Theory of Acceptance and Use of Technology) and IDT(Innovation Diffusion Theory) of adoption-perspective, and suggests a resistance-incorporated adoption model from a new viewpoint. The analysis of questionnaire data indicates the following results: Performance expectancy, effort expectancy, price value, hedonic motivation in UTAUT2 and visibility in IDT have a significant negative influence on innovation resistance. Compatibility in IDT and MIR exerts a positive influence on perceived value. Social influence and hedonic motivation in UTAUT2 positively relates to perceived value. Higher innovation resistance results in lower perceived value, with innovation resistance and perceived value negatively and positively affecting intention to use, respectively.

• Elastomers and Composites
• /
• 제51권2호
• /
• pp.93-98
• /
• 2016

The composites of EVA/EPDM including aluminum trioxide (ATH) as a fire retardant were manufactured for the purpose of improving low temperature property and flame resistance in the rubbery materials. The ratio of EVA to EPDM didn't affect the flame resistance of the rubber composites. The addition of ATH resulted in increase of the flame resistance. In the evaluation of the cold resistance, the increasing EPDM content showed enhancement of cold resistance in the composites due to increasing low Tg EPDM. It was found out that tensile strengths of the composites showed a maximum value at 100 phr of ATH by reinforcing effect, but a minimum value at 200 phr of ATH owing to slippage between the flame retardant by the external stress. In the measurement of solvent resistance in tetrahydrofuran, the increasing ATH content yielded enhancement of solvent resistance by reducing swelling of the composite, and increasing EPDM content also resulted from increase of the solvent resistance by reduction of polarizability as well as increase of crosslink in the composites.

• Applied Microscopy
• /
• 제47권3호
• /
• pp.95-100
• /
• 2017

High resolution measurements of the carrier profile in semiconductor devices is required as the semiconductor industry progresses from the 10-nm lithography node to 7-nm and beyond. We examine the factors which determine the resolution of the present method of scanning spreading resistance microscopy as well as such factors for the newer method of scanning frequency comb microscopy that is now under development. Also, for the first time, we consider the sensitivity of both methods to the location of heterogeneities in the semiconductor. In addition, mesoscopic effects on these measurements are considered for the first time. Two simple analytical models are extended to study the sensitivity to heterogeneities as well as mesoscopic effects.