• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.2
• /
• pp.57-62
• /
• 2003

The block assembly of ship consists of a certain type of heat processes such as cutting, bending, welding, residual stress relaxation and fairing. The residual deformation due to welding is inevitable at each assembly stage. The geometric inaccuracy caused by the welding deformation tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method which can explicitly account for the influence of various factors on the welding deformation. The validity of the prediction method must be also clarified through experiments. This paper proposes a simplified analysis method to predict the welding deformation of panel block structure. For this purpose, a simple prediction model for fillet welding deformations has been derived based on numerical and experimental results through the regression analysis. On the basis of these results, the simplified analysis method has been applied to some examples to show its validity.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.1
• /
• pp.64-70
• /
• 2002

This paper shows the results of the development of a small size of digital type continuous and intermittent welding auto-carriage based on microprocessor (Intel 80196KC) for welding process with long welding line. The developed welding auto-carriage loads welding torch and tracks welding line. It is an automaton largely used for welding process with a lot of long welding lines such as shipbuilding and structure. Most traditional auto-carriages have been developed based on analog circuit for open loop control. So this analog circuit welding auto-carriage cannon control welding speed. Specially welding auto-carriage for intermittent welding condition is so complicated and has the low precision of control performance in welding distance and non-welding distance. The auto-carriage developed in this paper has the following characteristics: It has not only functions of traditional carriage but also functions such as pseudo-welding process of big iron structures, intermittent welding in order to limit heat for welding thin plates, crater treatment of the final step of welding, acceleration at the initial step of welding and deceleration in the final step of welding. The main control board of auto-carriage, power supply system and DC motor drive wee developed and manufactured. The welding speed and the welding distance of the developed auto-carriage are controlled accurately by feedback control using photo-sensor. Hardware and software robust against the heat and noise produced on the welding process are developed.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.3
• /
• pp.238-245
• /
• 2011

Welding inevitably introduces the residual stresses which affect the fatigue strength of the joint structure. The mitigation of fatigue strength depends on the residual stress magnitude and distribution. Stress relief analyses are of practical interest for all cyclic loaded welded structures, such as ships and offshore structures. In order to estimate the effects of relaxation of residual stresses in the welded structure, this paper presents a finite element analysis procedure and experimental results for the welded structure. Cruciform specimens joint by MAG welding have been tested to measure the released stress. Relieved welding residual stresses obtained by finite element analysis are compared with those measured by experiment.

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.170-172
• /
• 2000

In this research, newly proposed heat source equations were calculated to predict micro distortion of small structure in laser welding and compared with experimental results which were measured using laser speckle metrology. A finite element code, ABAQUS is used for the heat transfer analysis with a three-dimensional plane assumption. The results suggest that weld distortion is varied according to the heat source of the. laser beam.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.97-99
• /
• 2006

A ship owner has been disappointed with the wrinkle, phenomenon visually occurring at the side shell structure of VLCC(very large crude oil carrier). In order to solve this problem, we have firstly performed a variety of actual measurements. Furthermore, comparing the welding deformation level of DSME(Daewoo Shipbuilding & Marine Engineering Co. Ltd.) with that of SHI(Samsung Heavy Industries), the superiority of deformation control level of Korean shipyard has been substantiated.

• Journal of Welding and Joining
• /
• v.15 no.2
• /
• pp.54-63
• /
• 1997

For the purpose of establishing laser welding condition (laser power, welding speed and beam focus) and of evaluating tailored blanks for two kinds of thin steel sheets SPCC and SK5M using in the thin plate structure such as automobile, train, and so on, investigated their $CO^2$ laser weldability under various initial welding conditions. SPCC thin sheet showed good weldability under some welding conditions. But, high carbon steel sheet SK5M needed heat treatment after welding to obtain ductility of the welded joint. And next, tailored blank was tested through deep drawing to evaluate reliability of their obtained laser welding conditions. The forming depths by tailored blank were SPCC+SPCC=22-25mm and SK5M+SK5M=13-25mm.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.55-60
• /
• 1999

In thin plate welding, welding deformation is deformation is produced in special form like buckling distortion, which is different from one in thick plate welding, large quantitatively, and has complicated form. Therefore, a particular countermeasure to prevent the welding deformation in manufacturing process is requested. Otherwise it takes more time to straighten the welding deformation than to fabricated a steel structure newly and in case of failing to straighten the welding deformation in beginning of the flame straightening process, even if the flame straitening is completed, the appearances is not good and sometimes eve refabrication is needed. To minimize these problems. In this present paper, the effects of the condition of support pin on out-of plane deformation produced by thin plate Butt welding in investigated through experiment and the countermeasure to prevent the welding deformation in suggested.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.5
• /
• pp.389-395
• /
• 2019

Turret mooring type Floating Production Storage and Offloading (FPSO) is designed to rotate the hull around a turret system. The system is mounted inside a cylindrical moon-pool structure of the ship hull structure. The upper part of the moon-pool structure called Bogie Support Structure (BSS) is supported on ring type rail structure (bogie), so high roundness is required at the top of the structure. In this study, the deformation measured during BSS installation was compared with the predicted values through the thermal elasto-plastic analysis, and the causes of deformation were analyzed. Deformation behavior of cylindrical structure with a very large diameter compared to the thickness was investigated. In addition, a proper welding sequence and correction method for the deformed structure were proposed. This study can be an example of the solution to the tolerance problem of large cylindrical structures.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.2
• /
• pp.87-91
• /
• 2009

The welding distortion of a hull structure in the shipbuilding industry is inevitable at each assembly stage. The geometric inaccuracy caused by welding distortion tends to preclude the introduction of automation and mechanization and requires additional man-hours for adjustment work during the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method that can explicitly account for the influence of various factors on the welding distortion. The validity of this prediction method must also be clarified through experiments. For the purpose of reducing the weld-induced bending deflection, this paper proposes the plastic counter-deforming method (PCDM), which uses line heating as the optimum distortion control method. The validity of this method was substantiated by a number of numerical simulations and actual measurements.

• Journal of Welding and Joining
• /
• v.21 no.4
• /
• pp.80-86
• /
• 2003

Arc-spot welding is generally used in joining of precise parts such as case and core in electric compressor. It is important to control joining deformation in electric compressor because clearance control of micrometer order is needed for excellent airtightness and anti-nose. The countermeasures for this deformation in field have mainly been dependent on rule of try and error by operator's experience because of productivities. For control this deformation problem without influence on productivities, development of exact simulation model should be needed. In this study, on the basis of previous study, the analysis model io predict deformation of precise order in arc-spot welded structure with non-uniform stiffness is brought up through feedback and tuning between monitoring data and analysis results. For this, deformation monitoring system was built and boundary condition considering mechanical melting temperature was applied.