• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.46-57
• /
• 1990

TMCP steel manufactured by controlled rolling followed by accelerated cooling process is known to have extra-ordinary mechanical properties such as tensile strength and toughness. However, there is much uncertainty about the fatigue fracture characteristics, especially, in the welded state of this steel. In case of this steel, the softening zone by welding is generated in heat affected zone in contrast with the case of conventional normalized high strength steel. This softening zone is considered to play significant roles in low cycle fatigue fracture of the welded part of this steel. In this paper, the low cycle fatigue behaviors of TMCP steel were inspected in as-received and welded state using the smooth specimen. The fatigue life-time was seperately investigated on the basis of failure of the specimen and crack initiation which is detected by differential strain method. Moreover, the low cycle fatigue characteristics of TMCP steel were quantitatively compared with those of the conventional normalized steel of same strength level.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.4
• /
• pp.275-281
• /
• 2016

One of the most important things for quality to meet ship-production schedule is an accuracy control. A ship is assembled by welding through whole production process, so it is important that loss by correction will not happen as much as possible by using some engineering skills like reverse design, reverse setting and margin for thermal shrinkage. These efforts are a quite effective in fabrication stages, but not in erection stages. If a ship block which consists of common steel is exposed to directional solar radiation, its dimensional accuracy will change high as time by its thermal expansion coefficient. Therefore, the measuring work would be often done at dawn or evening even with having a very accurate device. In this study, an FE analysis method is developed to solve this problem. It can change measured data affected by solar thermal distortion to ones not, even though ship-block is measured at an arbitrary time. It will use the time when measuring, the direction of block and the weather record by satellites. It is confirmed by a comparison between measured data of a ship-block and the result by suggested analysis method. Furthermore, a pre-processing system is also developed for fast application of the suggested analysis method.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.331-333
• /
• 2005

It comes up conversation in automobile industry that some technologies related to production and quality for goods have to be developed to make rationalization of the unit cost of production because material of car muffler is replaced by expensive stainless steel having corrosion-resistance and oxidation-resistance. Quality evaluation and control is direct method for the company producing welded goods in large quantities to increase productivity and to improve quality. It seems that prevention of inferior quality and increasement of productivity will be hard if production design does not have quality evaluation method related to weld assembly, They have been producing welded goods using MIG weld but still do not have not only quality evaluation method but also evaluation criterion for welded joint. In this study, the way for development of quality evaluation method is showed by analysis and calculation of waveform to improve technology related to welding process

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.132-134
• /
• 2005

The friction surfacing system which has been successfully developed in RIST has both position control and force control by using hydraulic cylinder. In friction surfacing process mechtrode rotation speed(N) and feeding speed($V_{z}$), travelling speed($V_{x,y}$) are of critical importance for the width and thickness of the coating. As a result of DOE with developed system, the main effect of coating thickness is a rotation speed of mechtrode.

• Journal of Welding and Joining
• /
• v.21 no.4
• /
• pp.39-45
• /
• 2003

Nano-TiO$_2$ photocatalytic coatings were deposited on the stainless steel 304(50$\times$70$\times$3mm) by the APS(Atmospheric Plasma Spraying). Photocatlytic reaction was tested in MB(methylene blue) aqueous solution. For applying nano-TiO$_2$ powders by thermal spray, the starting nano-TiO$_2$ powder with 100% anatase crystalline was agglomerated by spray drying. Plasma second gas(H$_2$) flow rate and spraying distance were used as principal process parameters which are known to control heat enthalpy(heat input). The relationship between process parameters and the characteristics of microstructure such as the anatase phase fraction and grain size of the TiO$_2$ coatings were investigated. The photo-decomposition efficiency of TiO$_2$ coatings was evaluated by the kinetics of MB aqueous solution decomposition. It was found that the TiO$_2$ coating with a lower heat input condition had a higher anatase fraction, smaller anatase grain size and a better photo-decomposition efficiency.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.52-55
• /
• 1997

This paper discusses an automatic visual-servoing system, in which a laser and a CCD camera are used for imaging the pattern of joint groove. The algorithm used here is simple and robust to find out the gap width and gap center. As a consequence, the speed of algorithm is very fast and optimized. A feature of this system is that it processes only by summing the vertical line and horizontal line of screen without any image preprocessing in order to get the energy information of lines alternatively. It is practical and useful for the system requiring a fast process time of vision.

• Proceedings of the KWS Conference
• /
• 1995.10a
• /
• pp.110-112
• /
• 1995

Initial solder joint strengths of various solder pastes, such as Sn-Pb(63-37wt%), Sn-In(52-48wt%), Sn-In-Ag(77.5-20-2.5wt%), and Sn-Ag(96.5-3.5wt%) has been studied. A system that can control the solder joint interface temperature during bonding process was also desined and implemented to improve solder joint integrity.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1278-1280
• /
• 2004

In this paper, we propose a new diagnosis method of DC/DC converter aging. The method is based on the variations of parasitic resistor for the aging process. We apply an on-line diagnosis of DC/DC converter because the observation is not a device, but a system. This study proposes a method of DC/DC converter diagnosis by analyzing the variations of model on the variations of parasitic resistor.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.218-221
• /
• 2007

The surface mounting technology of 0402 electric chip part is necessary to fabricate a high density and multi-functional module, but there is a limitation of the technology, like as a bridge and self-alignement. This work estimated SMT processing factors of 0402 chip. To obtain optimum SMT process, we evaluated effects of stencil thickness, shape of hole on printability and mountability. Printability shows best results under the thickness of $80{mu}m$ with circle hole shape and 90% square hole shape. In case of chip mounting process, chip mis-alignment and bridge was occurred rarely in same conditions. In more thin stencil thickness, $50{mu}m$, strength of 1005 chip parts was poor, because of amount of printed solder was insufficient.

• Journal of the Korean Institute of Gas
• /
• v.18 no.1
• /
• pp.46-51
• /
• 2014

The purpose of this paper is to study of the vehicle lamp manufacturing system composing ultrasonic waves connection process. Making lamp assembly plant, it was produced in the separate process as the injection molding, ultrasonic waves bonding, annealing in the constant temperature, lamp assembling and packing. But the improvement method producing the lamp was added with one-step process by one automation technique. As a result, welding with ultrasonic waves process, the method decreased the energy consumption and noise during ultrasonic waves welding. Therefore, this method used the mathematics modeling for checking validity, it selected the stability and suitable controller using transfer function of plant and bode chart. In this study, the $180^{\circ}$ revolution control system to turn injection part upside down was $M_{eq}\;lcos{\theta}(t)$ because of gravity influence. It effected to unstable condition a system. For solving this problem, it aimed the linearization and stabilization of system by elimination $M_{eq}\;lcos{\theta}(t)$ as applying Free-forward control technique.