• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.362-366
• /
• 1990

The resistance spot welding process has been extensively used for joining of sheet metals, which are subject to variation of many process variables. Many qualitative analyses of sampled process variables have been successfully attempted to achieve a uniform nugget size. In this paper, the electrode movement signal which is a good indicative of the nugget size was examined by introducing a mathematical model with four parameters. A neural network method was applied for the estimation of the nugget size by four parameters. The prediction by the neural network is in good agreement with the actual nugget size. The results are quite promising in that the qualitative estimation of the invisible nugget size can be achieved without destructive testing of the welds.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.110-117
• /
• 2005

Underwater wet arc welds were experimentally performed on 11mm thick KR-RA steel plate using six different types of flux coated electrodes of 4.0mm diameter, KSKR, KSKT, USBL, JPUW, UWEA and UWEB. From analysis of bead appearance, detachability of weld slag, spatter occurrence and arc stability, JPUW gives the best result, and UWEB is superior to KSKR and KSKT. By experimental result of hardness distribution on the weld bonds, UWEB weld has the narrowest bond structure which is probable condition to get the best mechanical properties of weld. UWEB and JPUW welds have more even hardness distribution across weld deposit and base metal. Upon polarization test to measure the respondency of corrosion, the electrode of UWEB shows the most excellent degree due to the low open circuit potential difference.

• Journal of Welding and Joining
• /
• v.19 no.3
• /
• pp.334-341
• /
• 2001

The chemical and geometric effects of weld on flow-accelerated corrosion (FAC) of SA106 Gr.C low alloy steel pipe in 3.5wt% NaCl and simulated feedwater of nuclear power plant have been investigated by using rotating cylinder electrode. Polarization test and weight loss test were conducted and compared at rotating speed of 2000rpm (3.14m/s) with the variables of chemical and geometric parameters. The results showed that the chemical effects were relatively larger than the geometric effects, and the welded parts were the local anode and preferentially corroded, which could be explained by the differences between microstructural and compositional parameters. On the other hand, under active corrosion conditions, the heat affected zone were severely corroded and microstructural effects became the important role in the whole process.

• Journal of Welding and Joining
• /
• v.9 no.4
• /
• pp.69-74
• /
• 1991

The Plasma Arc Cutting Method using high density and hight temperature beam is well applicable to the cutting of the nonferrous metal (Al alloy ) and stainless steel which are unable to be cut by the use of the oxy-fuel gas. This study focalizes on the cutting phenomena of the plate of (mm) thickness, since the cutting phenomena of thick plates have been rather thoroughly studied. In this study the cutting groove, adhesive phenomena of dross, surface roughness were measured according to the variation of cutting speed and compared with the case of mild steel plates. The result showed that the kerf width variation of Al alloy was similar to the case of mild steel, while that of the stainless steel differed from the mild steel. In the adhesive phenomena of dross, 6(mm) thick plates of Al alloy showed a difference from those of thick plates, but the stainless steel was similar to thick plates. The surface roughness variation of Al alloy wias minimum at 67 cm/min, while that of stainless steel was at 30cm/min.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.111-118
• /
• 2006

Underwater wet arc welds were experimentally performed on 11mm thick KR-RA steel plate using six different types of flux coated electrodes of 4.0mm diameter, KSKR, KSKT, USBL, JPUW, UWEA and UWEB. From analysis of bead appearance, detachability of weld slag, spatter occurrence and arc stability, JPUW gives the best result, and UWEB is superior to KSKR and KSKT. By experimental result of hardness distribution on the weld bonds, UWEB weld has the narrowest bond structure which is probable condition to get the best mechanical properties of weld. UWEB and JPUW welds have more even hardness distribution across weld deposit and base metal. Upon polarization test to measure the respondency of corrosion, the electrode of UWEB shows the most excellent degree due to the low open circuit potential difference.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.1
• /
• pp.21-24
• /
• 2002

The electrode materials for welding machine in automobile industry such as Cu-Cr, Cu-Zr and Cu-$Al_2O_3$ require the high electrical conductivity and the proper hardness. Therefore the effects of solution heat treatment and aging treatment on the electrical conductivity and hardness of Cu-0.8wt%Cr and Cu-1.2wt%Cr alloys have been investigated. Cu-0.8wt%Cr alloy showed the higher electrical conductivity and hardness than Cu-1.2wt%Cr alloy and both alloys showed the better electrical conductivity at $930^{\circ}C$ among 930, 980 and $1030^{\circ}C$ solution heat treatment temperatures. The electrical conductivity and hardness in both alloys were not affected by aging treatment but remarkably affected by solution heat treatment temperature. The final drawing process reduced electrical conductivity and increased hardness more in Cu-1.2wt%Cr alloy.

• Journal of Power System Engineering
• /
• v.9 no.1
• /
• pp.50-56
• /
• 2005

The corrosion experiment was performed for 120 hours on the specimens in the natural seawater tank with four steps of the loaded torsional stress. The surface corrosion pattern of SCM440 area was showed global corrosion and narrow pitting, that was cause by galvanic corrosion between friction welded IN713LC and SCM440. But corrosion does not proceeded from IN713LC area. Initially, the average relative electrode potential and corrosion current were decreased suddenly, by and large, it was stabilized gradually tend to decreasing with the elapse of the immersion time. The corrosion rate was decreased by increasing the load stress, but 200 MPa specimen was showed most large value.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.198-201
• /
• 2001

The mixed gas of Hydrogen and Oxygen is gained from water electrolysis reaction. It has constant volume ratio 2 : 1 Hydrogen and Oxygen, and it is used as a source of thermal energy by combustion reaction. This gas has better characteristics in the field of economy, efficiency of energy, and environmental intimacy than acetylene gas and LPG used for gas welding machine. So several studies of this gas are actively in progress nowadays. The object of this study is the optimization of power condition in the side of electrical for the high efficiency of water electrolysis equipment. First, chemical analysis of electrolysis is conducted, and the relation of electrical energy and chemical energy is quantitatively investigated. For basic experiment, unit electrode of singular electrolysis electrode is manufactured and experimented, results are compared and analyzed with simulation, and the electrolysis is electrically equivalent.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.95-100
• /
• 2021

If we know the location of the hull block and the welding feeder in the shipyard, we can easily obtain the location information of the worker. That data is very useful for implementing a workplace safety monitoring system. However, it is difficult to apply a fixed communication network to the workplace due to the specificity of the hull structure and welding process. In this study, inductive power line communication, which can replace dedicated communication line, was reviewed. A ferrite core was used as an inductive coupler to be installed on the power cable of the welding machine, and a nano-crystalline core was applied as a coupler to be fastened to the support rod of the metal block. In order to visualize the operating principle of the proposed couplers, 3D modeling and finite element analysis were performed with the COMSOL AC/DC module. In the communication performance test using an aluminum profile, when the communication channel was formed by the contact of the welding electrode, the bandwidth was kept above 6 Mbps.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.3
• /
• pp.19-25
• /
• 1984

In the welded structure, the most dengerous section is welded parts and almost fractures of welded structure occur from welded parts. Accordingly, in other to prevents of fracture, it is important seeking the fracture behavior of welded parts. In this study as basic investigation of fracture behavior of welded parts, it is investigated that local distribution of fracture toughness and effect of multipass electrode welding, also effect of release of residual stress were investigated, as the subjected. material, the used steel having fatigue history and unused steel were selected. As the result of this study, it is dear that the base metal of unused steel and heat affected zone and weld metal are different each other in fracture toughness, and it seems clear that the weld metal may will become source of fracture because of it having the most low fracture toughness. Especially, in the case of crack occur in the used steel, it will be the most brittle section in the structure because of it having low fracture toughness then weld metal. It affirmation that, if welded parts has not flaw, the multi pass electrode welding effective to improve of fracture toughness, also release of residual stress is none effective to improve of fracture toughness in this study.