• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.27-32
• /
• 2001

This paper is studied about welding conditions and weldability of seam welding for galvanized steel sheet of automotive. The fuel tank of automobile is made by seam welding to be required of airtight or oiltight. This method have required a short time for welding, simplicity operation progress and little HAZ. Especially, it has more less residual stress and transformation than different welding progress. So, this study is for decreasing the leakage occurrence rate and to make standard operating condition table anyone can operate easily. Therefore, this study is analyzed the optimum conditions of seam welding for making the automobile with galvanized steel sheets by means of observing the microstructure and configuration back projection, RT, tensile-shear strengths test and SEM. Optimum conditions of seam welding obtained as follows, current 17.2-17.6kA speed 1.0m/min weld time 4:10:6 and current 16.5-17.4kA, speed 0.83m/min, weld time 4:10:4 at t1.0, and current, 18.5-18.9kA, speed 0.8m/min, weld time 4:10:4 and current 16.5-17.4kA, speed 0.68m/mi, weld time 4:10:2 at t1.6.

• Journal of Welding and Joining
• /
• v.29 no.4
• /
• pp.41-47
• /
• 2011

GMA welding process is a production process to improve productivity for the provision of higher welding quality of material. These includes numerous process variables that could affect welding quality, productivity and cost savings. Recently, the welding part of construction equipment had frequent failure of major components in the welding part of each subsidiary material due to shock which is very poor according to the welding part. Therefore, the implementation of sound welding procedure is the most decisive factor for the reliability of construction machinery. The data generated through experiments conducted in this study has validated its effectiveness for the optimization of bead geometry and process variables is presented. The criteria to control the process parameters, to achieve a good bead geometry. This study has developed mathematical models and algorithms to predict or control the bead geometry in GMA fillet welding process.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.4
• /
• pp.56-61
• /
• 2000

This study has been performed for mechanical properties of underwater wet welding electrode with rolled steel (KR-RA) for ship structure, one kind (E 4313) of domestic covered arc welding electrode used in the air and two kinds (UWE-01, UWE-02) of underwater covered arc welding electrode experimentally developed on the same welding condition. The results obtained were as follows : The hardness value of underwater covered arc welding electrode (UWE-01) was about 8.3% lower than domestic covered arc welding electrode(E 4313) in heat affected zone of test of UWF-02 was lower about 4.5%. Tensile strengths of UWE-01 were about 0.9%, and those of UWE-02 were about 6.5% higher than those of domestic covered arc welding electrodes (E 4313) in test specimens. The impect value of UWE-01 were about 15.5%, and those of UWE-02 were about 21.7% highter than those of domestic covered arc welding electrodes(E 4313) in test specimens. So mechanical properties of the underwater arc welding electrode were improved by the composition ratios of covering materials.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.129-140
• /
• 1998

An interface system was developed to offer the welding capability to a robot controller which had not any embedded function for arc welding before, and also an arc sensor algorithm was proposed for weld seam tracking of the welding robot. For the interface system between the robot controller and welding equipments, data communication software and interface connections were composed. The interface system was mae to correspond welding condition, correction data, operation sequence and current status with the robot controller by mutual had shaking and digital signal transfer. Graphic user interface program developed under the environment of windows made it easy to monitor data communication and operation status, and to control welding and sensing sequence. Arc sensing algorithm proposed in this study to compensate torch position error was based on a fuzzy logic with the variables of current difference and current differenced change at torch weaving extremities. The developed interface system could be successfully implemented in between welding equipments and the robot controller, and showed normal status and exact function in data and signal communication between the systems. The whole robot welding system was then examined to verify its welding and seam tracking capabilities in horizontal fillet, vertical fillet, and 3-dimensional fillet weldment. The experiments revealed sound weld bead shapes and also good seam tracing results.

• Journal of Welding and Joining
• /
• v.18 no.1
• /
• pp.91-96
• /
• 2000

Characteristics of the weld defect, such as a blowhole and a pit in lap-jointed fillet Co₂ welds of Zn-coated steel sheet were studied in order to make clear the sequence of the blowhole formation during welding. Main conclusions obtained are as follows: 1) Blowhole, wormhole and pit were found in fillet welds, although the optimum welding condition of 200A-23V-100cm/min was applied. 2) Zn was only detected at the solidification boundary at the early stage of the blowhole formation. 3) Most of the blowholes was started to form at lap-joint by the Zn vapor. With increasing of the Zn vapor and its pressure, the blowhole was develope to th bed surface until the completion of weld solidification. 4) The behavior of the blowhole in growth was similar to that of the columnar dendrite during welding.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.1
• /
• pp.102-107
• /
• 2006

This study investigates the properties as the difference friction welding area on SM25C steel rod. The tensile and bending strength and of welded joints, the hardness distribution of welds, the microstructure of welds and the tensile fracture surfaces were mainly investigated through this experiment. The fixed friction welding conditions were revolution 2000rpm, friction pressure 70Mpa, friction time 1.5sec, upset pressure 100Mpa, upset time 2.0sec, upset length 2.8mm and changeable friction welding parameter was friction welding area.

• Journal of Welding and Joining
• /
• v.4 no.1
• /
• pp.32-39
• /
• 1986

This paper was studied about the influence of oxidized films on workability in cold pressure welding. In preceding studies, the principal foci of the studies about pressure welding were considered several factors(surface manufacturing methods, surface roughness, pressure welding speed and surface temperature). But the influence to the growth of oxidation have hardly known well. So the purpose of this paper consists in solving the question above and proposing the optimal states of the pressure welding. Therefore the results obtained is as the following; When the oxidation time is within about 2 minutes, the bonding strength is very good after surface manufacturing of the neighboring to be bonded. The more surfaces are fine the more bonding strength is excellent. Above all, the optimal condition of cold pressure welding is the state that the characteristic value is 38% with smooth surface and without oxidation.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.61-63
• /
• 2004

Recently many research works are going on in the field of application of Laser-Arc hybrid welding for superstructures such as shipstructures. However, the study on heat distribution and welding residual stress of hybrid weld by numerical simulation loaves much to be desired. Therefore in this study an optimized welding condition and numerical simulation for hybrid welding by using Previous numerical analysis which was used to calculate the kent source for hybrid welding has been analyzed.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.563-568
• /
• 1999

Generally the control method of wire feeding motor in welding machine has been used full-wave phase control method. The fire-angle control generates low frequency speed ripple, and it causes the output current ripple. So it results in the variation of welding condition and low welding performances such as spatter generation and bead state. For the purpose of welding performances improvement by speed controller in wire feeding motor, in this paper the constant speed control method for welding machine is proposed. The proposed system is composed of speed control loop and current control loop. As a result of experiment by using proposed constant wire feed experiment by using proposed constant wire feed speed controller, the output voltage and current waveform and metal transfer are maintained stably. And moreover the number of instantaneous short circuit occurrence is reduced remarkably.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.729-733
• /
• 1997

Due to the variety of disturbance, it is not ease to accomplish the in-process detection of weld line with non-contact sensor. To get around this difficulties problem develop an automatic seam tracking weld system, the reliable signal processing algorithm has been recommanded. In this research, laser displacement sensor is applied as a seam finder in the automatic tracking system. The sensor is controlled by a dc servo motor which is mounted at X-Y moving table. X-Y moving table manipulated by an ac servo motor controls the position and velocity of the welding torch. First, X-Y table moves to Y-axis to search the welding joint feature before starting the welding, and welding joint is from the scanning data and weighting factor for each other. Second, weld line is determined using proposed signal processing algorithm during welding process. Form the experimental results, we could see the possibility that laser displacement sensor with procesed algorithm can be used as a seam finder in welding process under the severe noise (spatter,arc light etc.) condition