• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.193-196
• /
• 2006

Recently many research are going on in the field of application of Laser and Laser-Arc hybrid welding for superstructures such as ship-structures, transport vehicles etc. Therefore in this study an optimized welding condition and numerical simulation for hybrid welding by using previous numerical analysis which is used to calculate the heat source for Laser and Laser-Arc hybrid welding has been analyzed. For this purpose, fundamental welding phenomena of hybrid process(Laser+MIG) are determined based on the experiments. In order to calculate temperature and residual stress distribution in Laser and Laser-Arc hybrid welds, finite element heat source model is developed on the basis of experiment results and characteristics of temperature and residual stress distribution in Laser and Laser-Arc hybrid welds are understood from the result of simulation and found comparable to the experimental values.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.98-106
• /
• 1999

In GMAW, the spatters are generated according to the variation of the arc. Of the arc is stable, Few spatters are generated. But if unstable, too many spatters are generated. So, this means the spatters are dependent on the arc state. The aim of this study is to accurately estimate the arc state. To do this, the generated spatters were captured under the some welding conditions, and the waveforms of the arc voltage and welding current were collected. From the collected signals, the waveform factors and their standard deviations were extracted. Using these factors as input parameters of multi-layer artificial neural network, the learning for the weight of the generated spatters is performed and the estimation results to the real spatter are assessed. Obtained results are as follow: the linear correlation coefficient between the estimated result and the real spatters was 0.9986. And although the average convergence error was set 0.002, the estimated error to the real spatter was within 0.1 gr/min at each welding condition. In the estimation for the weight generated spatters, the result with multi-layer neural network was far better than with multiple regression analysis. Especially, even though under the welding condition which the arc state is unstable (the spatter is generated much more), very excellent estimation performance was shown.

• Journal of Welding and Joining
• /
• 제12권2호
• /
• pp.39-48
• /
• 1994

In comparison to the conventional brazing, laser welding of ceramics has advantages of direct bonding without filler material, which causes the thermal stress due to the differences of thermal expansion coefficients. In pulse-mode, laser welding of dispersion ceramic having high thermal resistance is possible at relatively low preheating temperature of $1300^{\circ}C$ In CW-mode, alumina can be welded at high preheating temperature $1500^{\circ}C$ under the condition of low feed rate of 500 mm/min, respectively. Further studies on developing mechanism of pores in the bead during laser welding of ceramics is required.

• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.63-69
• /
• 2000

A genetic algorithm was applied to an arc welding process to determine near optimal settings of welding process parameters which produce good weld quality. This method searches for optimal settings of welding parameters through systematic experiments without a model between input and output variables. It has an advantage of being able to find optimal conditions with a fewer number of experiments than conventional full factorial design. A genetic algorithm was applied to optimization of weld bead geometry. In the optimization problem, the input variables was wire feed rate, welding voltage, and welding speed and the output variables were bead height, bead width, and penetration. The number of level for each input variable is 16, 16, and 8, respectively. Therefore, according to the conventional full factorial design, in order to find the optimal welding conditions, 2048 experiments must be performed. The genetic algorithm, however, found the near optimal welding conditions from less than 40 experiments.

• Journal of Welding and Joining
• /
• 제29권6호
• /
• pp.45-48
• /
• 2011

In this research, laser welding of automotive transmission components was investigated to replace electron beam welding which is normally conducted under vacuum condition. Fiber laser welding was applied to the automotive transmission components - hub clutch and annulus gear. In the component welding, the laser welding parameters were optimized to eliminate spatters and the end crater. By applying laser welding to the transmission parts, the process time could be reduced up to 70% compared with the current electron beam welding process.

• 한국항만학회지
• /
• 제14권1호
• /
• pp.87-95
• /
• 2000

This stability of a plate structure is very crucial problem which results in wrinkle and buckling. In this study, the effect of the pattern of spot-welding points of the two rectangular plates on the compressive and shear buckling load is studied with respect to the thickness, aspect ratio of plates and number of welding spots. Buckling coefficient of the plate not welded was compared with that of two plates with various thickness to extract the effect of thickness. The effect of number of welding spots are studied in two directions, longitudinal and transverse directions. The conclusions obtained were that the reinforcement effect was maximized when the aspect ratio was close to 1.75 at compressive load condition and that the effect of number of welding spots in transverse direction was larger than that in longitudinal direction at shearing load condition.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.55-65
• /
• 1997

The stress intensity factor has been calculated for the cracked plate subjected to remote normal stress and reinforced with a plate by symmetric spot welding. The solution was based on displacement compatibility condition between the cracked sheet and the reinforcement plate. It is shown that the results from the derived equation for stress intensity factor were agreed with previous solutions. The reinforcement effect gets better as a joining spot is closer to the crack tip and the other joining spots become nearer to the crack surface.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.77-79
• /
• 2006

To achieve high productivity of assembly hull blocks, it is important to predict welding deformations accurately and to apply these data to the production planning. In the deformation analysis of hull block, simplified methods (elastic analysis) such as inherent method, equivalent loading method and local & global approach are usually used instead of thermal-elastic-plastic analysis because of calculating time and cost. To be much more practical, these simplified methods should consider gravity effect of plate and contact condition between the plate and the positioning jig. In this research, using finite element method, practical predicting method for the welding deformation of the curved hull blocks with considering welding sequence, gravity effect and contact condition is proposed.

• 한국해양공학회지
• /
• 제10권1호
• /
• pp.36-46
• /
• 1996

This paper deals with determinig the proper friction welding condition and analyzing various mechanical properties of friction welded joints of sintered carbide tool materials(K20, P25, and SKDX5 for the blade part of drill or press punch) to alloy steel (SKH4, SCM440 for the shank part of drill or press punch), the alloy steel to aluminum(A6061 for the interlayer material between the blade part and the shank) and sintered carbide tool materials to alumminum. And also acoustic emission test will be carried out during fiction welding to evaluate the weld quality.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.803-808
• /
• 2000

This thesis studied whether friction welding of SPSS, localized torsion bar material could be accomplished or not. And then optimum welding conditions were examined and leaded through tensile, impact, torsion and hardness test after postweld heat treatment of the actual field condition. Obtained results were as follows; Linear relationship was existed between heating time and total upset, and a quadratic equation model could be made between tensile strength and heating time. Optimum welding conditions with fine structure were as follows in case total upset(U)=8.5mm; the number of rotations(n)=2,000 rpm, heating pressure($p_1$)=80MPa, upset pressure($p_2$)=200MPa, heating time($t_1$)=4sec, upset time($t_2$)=3 sec.