• Bulletin of the Society of Naval Architects of Korea
• /
• v.10 no.1
• /
• pp.15-20
• /
• 1973

In this paper, it is desired to show a simplified analytical method in estimating the thermal stresses in the heat affected zone of butt welded joint. A finite strip as shown in Fig.1 is taken as a analytical model for stress analysis. Expressing the temperature distributions by Fourier series, the thermal stresses are obtained. From the numerical sample calculation, the following results can be obtained. (1) Thermal stresses can be estimated by the sujected method. (2) The stress component, which is parallel to the weld direction is the largest stress component in major part of the strip. (3) In obtaining a stress component for the engineering purpose, length of the strip can be treated as five times of the thickness with same degree of convergency.

• Journal of Welding and Joining
• /
• v.24 no.1
• /
• pp.50-55
• /
• 2006

In an attempt to optimize friction spot joining process of Al alloys for automobiles, effects of joining parameters such as tool rotating speed, plunging depth, and joining time on the joints properties were investigated. A wide range of joining conditions could be applied to join Al alloys for automobile without defects in the weld zone except for certain welding conditions with a lower heat input. For sound joints without defects, tensile shear strength of joints was higher than acceptable criteria of tensile shear strength of resistance spot welded joints for aluminum.

• Journal of Welding and Joining
• /
• v.15 no.5
• /
• pp.46-55
• /
• 1997

This study has evaluated the liquation cracking behavior in the heat affected zone of several Ni base superalloys (Incoloy 825, Inconel 718 and Inconel 600). 304 and 310S austenitic stainless steels were also included for comparison. In addition, the mechanism of liquation cracking in the HAZ was postulated based on the extensive microstructural examinations with SEM, EDAX and TEM. The liquation cracking resistance of Ni base alloys was found to be far inferior to that of austenitic stainless steels. The liquation cracking of Incoloy 825 and Inconel 718 was believed to be closely related with the Laves-austenite(Ti rich in 825 and Nb rich in 718) and MC-austenitic eutectic phases formed along the grain boundaries by constitutional liquation and incipient melting under rapid welding thermal contraction. Further, liquation cracking resistance of the HAZ was dependent not only upon the type and amount of low melting phases but also on the grain size.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.177-179
• /
• 2005

In an attempt to optimize friction spot joining Process of Al alloys for automobiles, joining parameters such as tool rotating seed, plunging depth, and joining time on the joints properties were investigated. A wide range of joining conditions could be applied to join Al alloys for automobile without defects in the weld zone except for certain welding conditions with a lower heat input. for sound joints without defects, tensile shear strength of joints was higher than acceptable criteria of tensile shear strength of resistance spot welded joints for aluminum.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.223-225
• /
• 2005

In order to demonstrate the friction stir weldability of the Al 6061 T-6 unequal thickness joint and determine optimum welding parameters, the relations between welding parameters and properties of the joints have been studied in this paper. The experimental results showed that the tensile properties of the joints are affected by the welding heat inputs and tool shape. In this study, the maximum ultimate strength of the as-welded joint is equivalent to 78% and 18hour aged joint is equivalent to 93% that of the base metal. Though the voids-free joints are fractured at the thermally affected zone on the advancing side, the fracture occurs at the weld center when the void defects exist in the joints.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.19-25
• /
• 2001

The friction-welding SM25C is a substitute for the suing steel that is utilized in the machinery, airplane, and automobile, ok. This substitution would provide reduction of material and weight of welding parts. From the result we found that the strength of the friction welded joint was 529-617MPa and the toughness 1.2 times higher than that of the base metal. The optimal condition of friction welding was found as follows : n=2000rpm, $P_1$=68㎫, $P_2$=137MPa, $t_2$=2sec, $t_1$=2-4sec, Considering the strength, the hardness, and the reduction of area in the friction welding, the fiction welding using SUP9A and SM25C was found to cause no problem in on-the-job application.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.75-81
• /
• 2012

Dissimilar material friction welding such as STD11 and SCM440, we are considering of such things as strength and tenacity of welding interface, which consist of friction welding rotation frequency, friction heating pressure, upset forging-pressure, friction heating time, and upset forging-pressure time. From the study, obtaining the interrelationship between welding condition and quality(toughness, tenacity), we can set the best range of welding condition. while performing acoustic emission examination for the nondestructive evaluation, we can deduce the interrelationship among total acoustic emission counts, friction welding variable, and quality during friction welding, which can solve the manufacturing difficulty and enhance the economic value.

• Journal of the Korean Society for Railway
• /
• v.5 no.2
• /
• pp.55-60
• /
• 2002

This study proposes the post-processor simulator construction of ultrasonic signal for integrity evaluation of railway truck. For these purposes, the ultrasonic signals for defects(crack) of weld zone in frames are acquired in the type of time series data and echo strength. The detection of the natural defects in railway truck is performed using the characteristics of echodynamic pattern in ultrasonic signal. The constructed post-processor simulator agree fairly well with the measured results of test block(defect location, beam propagation distance, echo strength, etc). Proposed post-processor simulator construction of ultrasonic in this study can be used for the integrity evaluation of railway truck.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11b
• /
• pp.557-562
• /
• 1996

조사전 및 감시시험시 용접열영향부(heat affected zone, HAZ)의 인성평가를 위해 제작되는 샤피(Charpy) 충격시험편의 노치(notch) 위치에 대하여 현재의 규정에 대한 타당성을 검토하였다. 적용규정은 HAZ 시험편의 노치위치를 용접용융선(fusion line, FL) ＋ 모재측 0.8 mm 로 제한하고 있다. 그러나, 본 연구결과, 이 부위는 다층(multipass) 용접시 후속열이력에 의해 결정립이 미세화되어, 인장강도와 경도 및 충격인성이 모재나 용접부에 비하여 양호하게 나타났다. 한편, FL ＋ 4 mm 이상의 다른 위치에서는 강도와 경도 및 충격인성이 모두 모재와 용접부에 비하여 낮은 값을 보였다. 이는 다층용접에 의한 후속열이력 및 용접후열처리(post weld heat treatment, PWHT)에 의해 금속조직학적 영향을 받은 것으로 판단되었다. 일련의 시험결과로부터, 조 사전 및 감시시험용 샤피충격시험편의 HAZ 에 있어서의 노치위치에 대한 현재의 규정을 재검토할 필요가 있음을 제안하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.17-22
• /
• 1997

ASME SA508 Class 3 원자로압력용기강을 대상으로, 용접열영향부(heat affected zone, HAZ)의 최고온도(peak temperature) 등온분포도(isothermal diagram)를 작성 및 해석하였고, 재현(simulated) 열영향부 시험편을 제작하여 미세조직검사 및 기계적특성 시험을 실시하였다. 그 결과, 최고온도 등온분포도를 이용하여, 미소열영향부(subzone of HAZ)의 미세조직(microstructure)에 미치는 예열(preheat)온도와 용접입열량(weld heat input)의 크기 효과를 예측할 수 있었다. 또한, 재현 HAZ 의 기계적특성 시험결과, 용접용융선(fusion line) + 1 mm 이내의 위치로 대표되는 열 cycle 조건에서는 모재보다 양호한 강도와 인성을 보였고, 용접용융선 + 2~3mm부근에서 가장 미세한 조직(fine tempered lower bainite)과 우수한 충격인성을 나타냈다. 한편, 용접용융선 + 약 5mm 위치에서의 열 cycle 을 재현한 시험편에서는 미세조직의 변화(spheroidization of carbides)와 함께 인성 및 기계적 특성이 저하하여 모재보다 낮은 값을 보이는 것을 발견할 수 있었다.