• 대한기계학회논문집A
• /
• 제40권12호
• /
• pp.987-995
• /
• 2016

본 연구는 $ZrO_2$의 비커스 경도에 대한 쇼트 피닝 효과를 연구하였다. 쇼트의 크기는 ${\phi}180{\mu}m$와 ${\phi}300{\mu}m$를 사용하여 피닝하였다. 비커스경도는 압입하중 98 N과 294 N으로 측정하였다. 비커스 경도는 와이블 통계 해석을 수행하여, 볼 크기 및 압압 하중에 따르는 영향을 평가하였다. 척도 파라메터는 98 N 압입 하중 및 ${\phi}180{\mu}m$ 쇼트 볼에서 크게 나타났다. 형상 파라메터도 대체적으로 작은 쇼트 볼(180sp)이 크게 나타났다. 이것으로부터 SP처리에 의한 압축 잔류 응력은 $ZrO_2$의 기계적 성질의 향상에 좋은 방법이다.

• The Journal of Advanced Prosthodontics
• /
• 제11권4호
• /
• pp.202-208
• /
• 2019

PURPOSE. Fabrication of zirconia restorations with ideal mechanical properties in a short period is a great challenge for clinicians. The purpose of the study was to investigate the effect of heating rate on the mechanical and microstructural properties of monolithic zirconia. MATERIALS AND METHODS. Forty monolithic zirconia specimens were prepared from presintered monolithic zirconia blanks. All specimens were then assigned to 4 groups according to heating rate as Control, Group $15^{\circ}C$, Group $20^{\circ}C$, and Group $40^{\circ}C$. All groups were sintered according to heating rates with the sintering temperature of $1500^{\circ}C$, a holding time of 90 minutes and natural cooling. The phase composition was examined by XRD analysis, three-point bending test was conducted to examine the flexural strength, and Weibull analysis was conducted to determine weibull modulus and characteristic strength. Average grain sizes were determined by SEM analysis. One-way ANOVA test was performed at a significance level of 0.05. RESULTS. Only tetragonal phase characteristic peaks were determined on the surface of analyzed specimens. Differences among the average grain sizes of the groups were not statistically significant. The results of the three-point bending test revealed no significant differences among the flexural strength of the groups (P>.05). Weibull modulus of groups was ranging from 3.50 to 4.74. The highest and the lowest characteristic strength values were obtained in Group $20^{\circ}C$ and Control Group, respectively. CONCLUSION. Heating rate has no significant effect on the flexural strength of monolithic zirconia. Monolithic zirconia restorations can be produced in shorter sintering periods without affecting the flexural strength by modifying the heating rate.

• 한국품질경영학회:학술대회논문집
• /
• 한국품질경영학회 1998년도 The 12th Asia Quality Management Symposium* Total Quality Management for Restoring Competitiveness
• /
• pp.544-555
• /
• 1998

Although the bimodal mixed weibull distribution is used to developing burn-in model widely, the failure times for a component or a system is often truncated at some time, T, due to the obsolescence in the electronics industry. In this paper, we will determine minimum total cost and burn-in time by using the bimodal mixed weibull distribution and the truncated bimodal mixed weibull distribution under the free warranty policy. The results of this study are summarized as follows. First, when products or system is not repairable, the width of the change of burn-in time can be larger by ${\beta}_1,\;{\beta}_2$ Second, if burn-in time become longer, it will be impossible to consider the bum-in in a long time, and in this case, the burn-in time should be shorten by the acceleration burn-in. Third, in case that opportunity loss cost or repair cost is exceed the warranty cost, or the total cost of considering burn-in is larger than that of not considering burn-in, it is not existed burn-in time which makes total cost to minimize. Forth, the shorter life-cycle of product, the more burn-in times will be decreased and the cost in considering burn-in will be increased

• 품질경영학회지
• /
• 제11권1호
• /
• pp.10-17
• /
• 1983

본 연구에서는 제품의 수명시험을 수행하는데 있어서 수명이 지수분포를 따를 때의 결과를 [1]제품의 MTBF가 $T_1$인 경우, 검사에 통과될 확률 $1-{\alpha}$(${\alpha}$는 생산자 위험), 제품의 MTBF가 $T_2$인 ($T_1$ > $T_2$) 경우, 검사에 통과될 확률 ${\beta}$(${\beta}$는 소비자 위험)로 하여 수명이 Weibull 분포(Shape Parameter를 알고 있을 때)를 따를 때에로 확장하였다. 또한, 수명시험과 관계있는 검사특성곡선(QC curve)과 평균수명시험시간(Average Life Testing Time)을 구해 보았다. 비용분석은 [1]의 과정을 그대로 활용하였다. 위의 전 과정은 Level II Basic Language로 Programming하여 Micro-Computer를 이용하여 계산하였다. 본 연구와는 다른 관점에서 Weibull 분포의 수명시험계획을 다루었던 [6]의 결과는 모두 같은 방향 - 지수분포에 비해 수명시험시간의 절감 - 으로 귀결되었음을 알 수 있다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.339-343
• /
• 2009

본 논문에서 155mm 자주포 K9에 사용되는 추진장약 K676의 포구속도 확률분포에 관하여 분석하였다. K676 추진장약의 로트별 수락시험으로 얻어진 포구속도 자료를 분석하였으며 각 시험탄의 포구속도는 기준탄의 사격결과 값으로 보정하였다. 최근까지 수행된 사격시험으로 얻어진 모든 시험값에 대하여 적합도 검정을 하였으며, 정규분포, 2모수 와이블분포 및 3모수 와이블분포 중 정규분포가 가장 적합한 확률분포임을 확인하였고 와이블분포도 충분히 활용할 만하다. 변동계수로부터 추진장약의 양산능력이 균일하게 유지되고 있음을 알 수 있다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제16권1호
• /
• pp.32-40
• /
• 2016

Purpose: The purpose of this study is to analyze the effect of sampling points on accuracy of storage reliability estimation for one-shot systems by assuming a weibull distribution as a storage reliability distribution. Also propose method for determining of sampling points for increase the accuracy of reliability estimation. Methods: Weibull distribution was divided into three sections for confirming the possible to estimate the parameters of the weibull distribution only some section's sample. Generate quantal response data for failure data. And performed parameter estimation with quantal response data. Results: If reduce sample point interval of 1 section, increase the accuracy of reliability estimation although sampling only section 1. Even reduce total number of sampling point, reducing sampling time interval of the 1 zone improve the accuracy of reliability estimation. Conclusion: Method to increase the accuracy of reliability estimation is increasing number of sampling and the sampling points. But apply this method to One-shot system is difficult because test cost of one-shot system is expensive. So propose method of accuracy of storage reliability estimation of one-shot system by adjustment of the sampling point. And by dividing the section it could reduce the total sampling point.

• 정보기술응용연구
• /
• 제3권3호
• /
• pp.91-106
• /
• 2001

본 논문에서는 소프트웨어 테스트 단계중에 발생되는 테스트노력 소요량을 고려한 소프트웨어 신뢰도 성장 모델을 제시하여 시간종속적인 테스트 노력소요량 동태를 일정 테스트 노력일 때와 웨이불 테스트 노력일 때를 비교하여 연구한다. 테스트 단계중에 소요되는 테스트 노력의 양에 대한 결함 검출비를 현재의 결함 내용에 비례하는 것으로 가정하여 모델을 비동차 포아송 과정으로 공식화하며, 이 모델을 이용하여 소프트웨어 신뢰도 척도에 대한 데이터 분석기법을 개발하도록 한다. 테스트 시간의 경과와 신뢰도와의 관계도 심도 있게 연구한다. 목표신뢰도를 만족시키는 최적발행시각을 정한다. 개발 후 테스트를 시작하기 전의 신뢰도가 어떠한 조건에 있는가를 검토하여 각 조건에 따른 최저 발행시각을 결정한다. 일정 테스트 노력 곡선과 웨이불 테스트 노력 곡선 모두에 대해서 그 조건은 목표 신뢰도를 초과하는 경우, 목표신뢰도를 초과하지는 못하지만 어느 조건 이상인 경우, 어느 조건 이하인 경우로 대별되며, 이 중에서 이상적인 경우는 두 번째 조건인 경우이다.

• 한국해양공학회지
• /
• 제34권1호
• /
• pp.26-36
• /
• 2020

An extreme value analysis of metocean data which include wave, wind, and current data is a prerequisite for the operation and survival of offshore structures. The purpose of this study was to provide information about the return wave, wind, and current values for the Barents Sea using extreme value analysis. Hindcast datasets of the Global Reanalysis of Ocean Waves 2012 (GROW2012) for a waves, winds and currents were obtained from the Oceanweather Inc. The Gumbel distribution, 2 and 3 parameters Weibull distributions and log-normal distribution were used for the extreme value analysis. The least square method was used to estimate the parameters for the extreme value distribution. The return values, including the significant wave height, spectral peak wave period, wind speed and current speed at surface, were calculated and it will be utilized to design offshore structures to be operated in the Barents Sea.

• 한국공작기계학회논문집
• /
• 제15권4호
• /
• pp.63-68
• /
• 2006

This research presents the reliability analysis of the pneumatic actuator within the tape feeder that is used to transfer the correct force to linked parts during l.0E+7 cycles. First, the degradation analysis for thrust and air leakage is executed to obtain the failure data of a product based on its performance over time. Second, once the parameters has been calculated using the weibull 2-parameter distribution and MLE(Maximum Likelihood Estimation), information related to life such as reliability, failure rate, probability density function is estimated. Finally, MTTF(Mean Time To Failure) and $B_{10}$ life of actuators are calculated. MTTF means the mean life at the confidence level and $B_{10}$ life refers to the time by which 10% of the product would fail. In this study, failure causes and solutions are examined using the reliability analysis.

• The Journal of Advanced Prosthodontics
• /
• 제16권1호
• /
• pp.25-37
• /
• 2024

PURPOSE. To investigate the effect of sintering programs and surface treatments on surface properties, phase transformation and flexural strength of monolithic zirconia. MATERIALS AND METHODS. Zirconia specimens were sintered using three distinct sintering programs [classic (C), speed (S), and superspeed (SS)] (n = 56, each). One sample from each group underwent scanning electron microscopy (SEM) and grain size analysis following sintering. Remaining samples were divided into five subgroups (n = 11) based on the surface treatments: control (CL), polish (P), glaze (G), grind + polish (GP), and grind + glaze (GG). One sample from each subgroup underwent SEM analysis. Remaining samples were thermally aged. Monoclinic phase volume, surface roughness, and three-point flexural strength were measured. Monoclinic phase volume and surface roughness were analyzed by Kruskal-Wallis and Dunn tests. Flexural strength was analyzed by two-way ANOVA and Weibull analysis. The relationships among the groups were analyzed using Spearman's correlation analysis. RESULTS. Sintering program, surface treatment, and sintering × surface treatment (P ≤ .010) affected the monoclinic phase volume, whereas the type of surface treatment and sintering × surface treatment affected the surface roughness (P < .001). Type of sintering program or surface treatment did not affect the flexural strength. Weibull analysis revealed no significant differences between the m and σ_o values. Monoclinic phase volume was positively correlated with surface roughness in the SGG and SSP groups. CONCLUSION. After sintering monolithic zirconia in each of the three sintering programs, each of the surface treatments can be used. However, for surface quality and aging resistance, G or GG can be recommended as a surface finishing method.