• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1223-1232
• /
• 2008

In this paper, an analytic method is proposed to extract the reference slot admittance required for the design of a non-resonant waveguide edge slot array. A slot and two neighboring transmission line sections of the numerous alternately inclined slots with the identical inclination angle are modelled as a uniform lossy transmission line, and thus, the total ABCD matrix is easily calculated and compared with the simulated or measured one. From this procedure, the complex characteristic impedance and the complex propagation constant of the lossy transmission line are calculated and the normalized slot admittance is analytically obtained. In order to validate the proposed method, the admittance value of a reference slotted waveguide fabricated for designing the X-band edge slot array is extracted and it is compared with the one obtained by the other conventional method.

• Journal of Satellite, Information and Communications
• /
• v.10 no.3
• /
• pp.26-31
• /
• 2015

This paper deals with a size-reduced Ku-band waveguide limiter. Basically, it passes the signal from 16.125 GHz through 16.375 GHz, but when excessively high power is injected to the input port, it should change to a bandstop filter. Furthermore, it is required to change to bring attenuation by more than 20 dB and 50 dB over a narrow band and the entire passband, respectively. Therefore, in order to meet this requirement, a limiting device is implemented with multiple PIN-diode posts that enable the limiter to be the bandpass filter and stopband one at the off and on states of the PIN-diode switch, respectively. So, the design goes through the equivalent circuit modelling and the geometry is realized in the accurate electromagnetic analysis CAD tool. Finally, the result is discussed to shed light on whether it complies with the aforementioned requirement.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.59-60
• /
• 2018

In this paper, we studied a design method for a band-pass waveguide filter with a modified H-type resonant iris (RI) placed in a thin transverse wall of a rectangular waveguide. The horizontal straight gap at the center of a conventional H-shaped iris is modified to a U-shaped one to increase the equivalent capacitance, and the equivalent inductance is improved by changing the vertical two straight slots into C-shaped ones. A third-order band pass filter using the proposed modified H-shaped iris was designed and, it was observed that the filter operated in the frequency range of 9.22-9.75 GHz with its insertion loss of 0.5 dB and return loss of 17 dB.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.409-418
• /
• 2020

In this paper, an integrated optical, evanescent-wave biosensor utilizing a multimode interferometer based on a Si₃N₄ rib-optical waveguide consisting of the Si/SiO₂/Si₃N₄/SiO₂ stacked structure was described. The theoretical background of the multimode interferometer was reviewed, and the structure and design process were presented through numerical computational analysis. We analyzed how the dimension (length, width) of the multimode interferometer affected the sensor performance. It has been confirmed through computational analysis that the changes in the refractive index of an analyte greatly affect the mode pattern formation position and output optical power of a multimode interferometer, and proved that this principle could be applied to integrated-optic biosensor.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.4
• /
• pp.47-52
• /
• 2012

We have designed the waveguide to microstrip transition using a probe structure for the center frequency of 200 GHz transceiver. The waveguide to microstrip transition is composed of probe, taper and microstrip transmission line. For design of the transition, we simulated the lengths and width of the probe and the taper to optimize the center frequency and the bandwidth using HFSS simulation tool from Ansoft. The transition is designed back-to-back structure. From the simulation results, the transition exhibits that insertion loss is below - 0.81 dB and the return loss less than -10 dB in range of 186 ~ 210 GHz.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.101-109
• /
• 2012

Because the installation problem of parabola antenna that is tilted to 45 degree when this antenna is installed at the area of middle latitude, the study on planar antenna in place of parabola antenna is made rapid progess. Especially, The development of the planar antenna for VSAT is needed depending on the increased Ka-band satellite communications. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level, the design method of the radiation power distribution control using the different slot widths is proposed. An array antenna consisting of 32 leakywave waveguide antennas is showing 35.16 dBi of gain, 2.5 degree of beamwidth at azimuth, below than -30 dB of sidelobe level, 45.8 degree of beam tilt angle in center frequency 30.2 GHz.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.3
• /
• pp.35-42
• /
• 2021

The research of amplifier have been actively conducted to replace the Traveling Wave Tube Amplifier (TWTA) in the mmWave. For Solid State Power Amplifiers (SSPA), which combine semiconductor-type devices to obtain high output, Low-loss, high-efficiency combination techniques are required to meet the required output as the output of a single relatively low device is relatively low. In this paper, we design and produce an 8-way waveguide combiner and a reflective loss of more than 20dB and a binding efficiency of 85% or more were identified. Field analysis calculates the critical power inside the combiner. It secured stable Power Ratings and built-in coupler for power monitoring to achieve miniaturization and light weight.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.3
• /
• pp.37-42
• /
• 2022

A high-performance wideband transition from microstrip to waveguide is proposed. This transition is designed by consideration of gradual field transformation and optimal impedance matching between microstrip line and fin-line. Clear design guidelines of proposed transition using fin-line taper with offset DSPSL (double-sided parallel stripline) are provided to determine the transition shape and the transition length. The fabricated transition exhibits less than 0.67 dB insertion loss per transition for frequencies from 85 to 108 GHz, and less than 1 dB insertion loss from 83 to over 110 GHz. Proposed transition is expected compact radar and various applications.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.487-488
• /
• 2012

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1986.10a
• /
• pp.20-22
• /
• 1986

This paper represents a graphical design technique of the symmetrical dielectric waveguids couplers. Once the phase constants are given by a approzimate model analysis, coupling lengths are easily calculated for each coupler. These method give some new insight of the codirectional couplers.