• ETRI Journal
• /
• v.46 no.3
• /
• pp.404-412
• /
• 2024

We propose a method for increasing the bandwidth of a substrate-integrated-waveguide (SIW) cavity-backed antenna with taper-based micro-strip SIW transition feeding. For radio transmission, a circular slot is etched on top of the SIW cavity. For optimal antenna design, the slot is etched slightly away from the cavity center to generate circularly polarized waves. Simulations show a wide axial ratio bandwidth of 7.860% between 11.02 GHz and 11.806 GHz. Experimental results confirm a similar wide axial ratio bandwidth of 4.9% between 10.8 GHz and 11.35 GHz. An SIW feed from an inductive window excites the radiating circular slot, resulting in a simulated wide impedance range of 1.548 GHz (10.338 GHz-11.886 GHz) and bandwidth of 13.93%. Experimental results show a wide impedance of 2.08 GHz (10.2 GHz-12.08 GHz) and bandwidth of 18.84%. The SIW cavity-backed antenna creates a unidirectional pattern, leading to gains of 6.61 dBi and 7.594 dBi in simulations and experiments, respectively. The proposed antenna was fabricated on a Rogers RT/Duroid 5880 substrate, and the reflection coefficient, radiation patterns, and gains were tested and compared using a computer simulator. The developed broadband antenna seems suitable for X-band applications.

• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.235-240
• /
• 2023

The optical signal injected into an end-fire optical phased array propagates along the waveguides inside the device and is emitted from the edge of the antenna. In general, reflection and scattering occur at the boundary, thereby reducing the emission efficiency of the optical signal. In this article, we propose a silicon nitride (Si₃N₄) tapered waveguide antenna structure whose width is tapered toward the emitting edge, achieving high emission efficiency operating at the 1,550 nm wavelength. The Si₃N₄ tapered waveguide antenna was numerically designed using the 3D finite-difference time-domain method. The optical signal emission efficiency increased from 78% to 96.3%, while reflectance decreased from 22% to 3.7% compared with the untapered waveguide antenna counterpart. This result will not only boost the optical signal intensity but also mitigate optical noise resulting from back reflection along the waveguide in the end-fire optical phased array device.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.1980-1985
• /
• 2010

This paper is about design of optimal structure of slot antenna array antenna with inner waveguide in accordance with the slot model, and fabrication of its prototype sample operating at the frequency of 24 GHz. Results of this work can be employed as a useful tool to develop and diversify slot antenna having superior performance and omni-directivity to that of current antenna. The implemented antenna demonstrates ultra-wideband performance for frequency ranges 24 GHz with the relatively high and flat antenna gain of 18.64dBi and low sidelobe levels. In addition, a $2{\times}8$ antenna array for phased-array systems and mm-wave sensor applications is also presented.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.4
• /
• pp.535-540
• /
• 2013

We design a slotted waveguide antenna for X-band which a 1.4m length with slot depth variation. A 54 slot array is modeled and simulated by CST, and the side lobe level is suppressed effectively in a certain range of frequency. The experimental results of the antenna show that its gain, maximum sidelobe level and half power beam-width are 21.8dB, -31dB and 2.0deg, respectively.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.5
• /
• pp.32-37
• /
• 1989

The design method of the center-fed resonant type slotted waveguide antenna using the Dolph-Tschebyscheff array is presented. Slot admittances are obtained by empirical and theoretical method since the effect of mutual coupling between slots is included. We design a slotted waveguide antenna which has 1.8ft. length and operates on 9.4GHz. The experimental results of the antenna show that its gain, maximum sidelobe level and half power beam-width are 25.5dB, -22dB and 3.6deg., respectively.

• Publications of The Korean Astronomical Society
• /
• v.8 no.1
• /
• pp.1-15
• /
• 1993

We made a pyramidal horn antenna system for 21cm cosmic radio wave. The antenna system has a rectangular waveguide with $TE_{10}$ mode and a copper probe to detect the electromagnetic wave in waveguide. The parameters of the probe are obtained by experiments using two waveguides. Pyramidal horn antenna is designed to get a gain of 20dB. The size of the aperture of this horn is $94cm{\times}74cm$. The beam width of half power is about $14.7^{\circ}$ for the frequency of 1.4GHz. The horn is made of aluminum plate with a thickness of 2mm. The signal from horn and waveguide is amplified in a receiver system and is converted into DC in the detecter. The intensity of the signal is recorded on a chart recorder. We observed the sun using this simple radio telescope and obtained the brightness temperature of $2.2{\times}10^5K$, which indicates that the sun is quiet at 21cm.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.209-215
• /
• 2017

In this paper, an antenna having 2-axes cross monopulse for Ka band millimeter-wave seeker is designed and antenna performance is verified through vacuum-brazing method for fabrication and measurement. Also, by designing and manufacturing a waveguide circulator the antenna including the circulator is measured. Radiating part of the antenna takes optimized slot lengths and offsets from Elliot's array synthesis procedure using the generic algorithm and feeding part for cross monopulse axes uses the folded waveguide to optimize the S-parameter result. Based on this method, the antenna has 33.3 dBi gain, $3.5^{\circ}{\pm}0.5^{\circ}$ beamwidth, below -23 dB SLL through fabricating and measuring. It is found that antenna characteristics is similar to design results.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.534-537
• /
• 2013

A compact monopole antenna excited by a conductor-backed coplanar waveguide (CBCPW) is developed for wireless USB dongle applications. The proposed antenna has a compact dimension of $14mm{\times}47.4mm{\times}3.5mm$, which is suitable for a USB dongle housing. A slotted elliptical patch and a CBCPW with vertical vias are employed to achieve a further size reduction and an improved impedance bandwidth. The measurement result demonstrates that the fabricated antenna resonates from 2.25 GHz to 10.9 GHz, which covers all of the important wireless communication bands, including WiBro (2.3 GHz to 2.4 GHz), Bluetooth (2.4 GHz to 2.484 GHz), WiMAX (2.5 GHz to 2.7 GHz and 3.4 GHz to 3.6 GHz), satellite DMB (2.605 GHz to 2.655 GHz), 802.11b/g/a WLAN (2.4 GHz to 2.485 GHz and 5.15 GHz to 5.825 GHz), and ultra-wideband (3.1 GHz to 10.6 GHz) services. The radiation characteristics of the proposed antenna when attached to a laptop are tested to investigate the influence of the keypad and the LCD panel of the laptop.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.1
• /
• pp.124-136
• /
• 2001

In this paper, we designed and manufactured the Ku-band circular waveguide antenna to do wireless communication with a ground radar as on-board antenna of missile. Using the MATLAB and the HFSS, we designed the circular polarizer which has a characteristic of circular polarization and broadband using the capacitive pin method, the feeder to feed coaxial line to circular waveguide, and a stopper to prevent a conductor material from being inserted. Then we simulated the designed antenna using the HFSS, obtained the gain and the radiation pattern. Because of a difficulty of manufacture, we established a manufacture process procedure. Antenna is manufactured with this procedure, test results of the manufactured antenna are the axial ratio of 1.37 ~ 1.72, the 3 ㏈ beamwidth of $72.23^{\circ}{\sim}78.54^{\circ},$ and the gain of 3.26 ~ 4.61 ㏈ within frequency band. We knew that these results are similar with simulation results. Also, we confirmed that the manufactured antenna is satisfied with requirement conditions through performance test, environmental test and flight test.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.55-56
• /
• 2017

In this paper, a wideband loop antenna is designed using a CPW feeding method for indoor digital TV applications. The proposed loop antenna consists of a square loop and two circular sectors which connect the loop with central feed points, and the CPW feed line is inserted in the lower circular sector. The CPW feed line is designed to match with the 75 ohm port impedance for DTV applications, and the ground slots are etched in order to improve the impedance matching in the middle frequency region. The optimized antenna is fabricated on FR4 substrate, and the experiment results show that it operates in the frequency band of 463-1,280 MHz for a VSWR < 2, which assures the operation in the DTV band.