• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.1
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.89-93
• /
• 2002

Resistance performance of 6.67 G/T class fishing vessel is experimentally investigated in low and middle speed ranges to find out the effect of a new chine. The tests are performed for four different cases in the circulating water channel(CWC). Wave patterns are observed together to make clear the relation between the resistance performance and the wave characteristics. The results show that the new chine can be one of the effective device to reduce the resistance.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.2
• /
• pp.69-74
• /
• 2016

A new wave-piercing-type high-speed planing boat without a chine was developed, and its basic performance was investigated in a model test, including the resistance, trim, and sinkage. The maximum speed of the developed ship was 35 knots. The hull form was developed by combining a VSV (very slender vessel) and TH (transonic hull), which have large deadrise angles at the bow. The main dimensions were estimated by a statistical approach using actual ship data. The effect of a side fin attached at the stern near the water line was investigated from a resistance point of view. It was found that the developed hull form showed the possibility of a new concept for a high-speed planing hull without a chine, and the side fin played an important role in increasing the resistance performance by controlling the trim and sinkage in the high-speed range.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.6
• /
• pp.632-640
• /
• 2019

Desalination plant ships have been recently regarded as one of the probable solutions for drought seasons in many countries. Because desalination plants should be mounted on the desalination ships and special purpose storages such as salty waste water tanks are necessary, onboard and compartment arrangements would be distinguished from those of other conventional commercial ships. This paper introduces some basic design procedure including resistance/propulsion and seakeeping performances. The ship lines were improved step by step after modification of the ship lines and verification of resistance/propulsion performances using computational fluid dynamics (CFD). After finalization of the ship lines, the seakeeping performance was also evaluated to check motion behaviors and drive wave-induced loads such as the wave shear force and bending moment. It was proved that the predicted long-term vertical wave shear force and bending moment were significantly less than the rule-based ones, thus it is expected that the deliverables of this study will reduce the construction cost of desalination plant ships.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.24 no.1
• /
• pp.35-41
• /
• 1987

An approximate method for calculating added resistance due to regular wave reflection has been established. In order to confirm the applicability of this method, an experimental work was carried out using a Series 60 model with oscillations in the 6-degrees of freedom restricted. Particular attention was paid to the case of the shorter wave length range where the effect of wave reflection is dominant compared to the effects of the ship's motions($\lambda/H=10.6-101.0,\;\lambda/L=0.23-1.18,\;F_n=0.10-0.25$). When comparing the measured and the computed resistance due to wave reflection in a head sea, good agreement is shown. This paper is based on research done by the Author as a member of the Ship Performance Group in the Department of Naval Architecture and Shipbuilding of the University of Newcastle-upon-Tyne in England, under the supervision of Dr. R.L. Townsin.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.79-84
• /
• 2004

Initial hull form of 10 G/T and 40 knots class coastal patrol boat is newly developed. The resistance performances are experimentally and numerically investigated by model test at high speed circulating water channel(CWC) and CFD technique. The effect of a fin attached at hull side and initial trim are studied together. Wave patterns are observed to make clear the relation between the resistance performance and the wave characteristics. it can be found that the initial trim plays a role to increase the resistance performance above a certain velocity.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.6
• /
• pp.1-6
• /
• 2013

A 25ft class fishing leisure boat is developed, and the resistance performances are investigated by a model test in a high-speed circulating water channel. The design speed of the developed ship is 25 knots using a 150 ps outboard engine. A catamanan type hull form using a planing section is adopted considering the Froude number and large deck area. The effect of a center body attached on the bottom of the cross deck is studied under various conditions. Wave patterns are observed to make clear the relationship between the resistance performance and the wave characteristics. The results show that the shape of the center body and the position of the chine line can have a strong effect on the resistance performance in a certain velocity range.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.6
• /
• pp.583-591
• /
• 2012

This study selected three model designs used for air injection type welding clothes designed for insulation purposes and analyzed the performance of each design. The bending characteristics were analyzed in order to identify the flexibility of the welded areas; subsequently, the seam breaking strength and water pressure resistance were analyzed to identify the bonding strength. In addition, two types of waterproof fabric, polyurethane (PU) coated 2 layer and PU laminated 2 layer fabrics, were used for a performance analysis, according to fabric processing specifications. The circle type showed the highest flexibility in the terms of bending characteristics that influence wearability and were followed by the wave and the straight type. In terms of breaking strength, the straight type showed the highest breaking strength, followed by the wave and the circle type. The water pressure resistance analysis found that the wave type was superior to the straight type in terms of water pressure resistance. The wave type is deemed to be a design type suitable for maximizing performance, provided that the issue of stabilization in the welding production process is addressed. Looking at the bending characteristics of waterproof fabric for each specification, the laminating waterproof cloth outperformed the coated waterproof cloth in terms of flexibility. However, in terms of seam breaking strength, the coated waterproof cloth outperformed the laminated cloth. In contrast, the water pressure resistance of the laminated waterproof fabric was found to be higher than the coated waterproof fabric, leading to the conclusion that the bonding strength of the laminated waterproof fabric is higher than that of the coated waterproof fabric based on the assumption of injecting air.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.251-256
• /
• 2002

Resistance performance of small size fishing vessel is experimentally investigated to find out the effect of fore-body shape and trim for the better hull form development. The tests are performed for four different cases in the high speed circulating water channel(CWC). Wave patterns are observed together to investigate the relation between the resistance performance and the wave characteristics.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.60-63
• /
• 2003

Resistance performance of 3 G/T class coastal leisure boat is experimentally investigated at high speed ranges and the effect of a fin attached at hull side is studied together. Wave patterns are observed to make clear the relation between the resistance performances and the wave characteristics.