• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.1
• /
• pp.25-34
• /
• 2017

The concentric dual-buoy Wave Energy Converter (WEC), which consists of external buoy (hallow-cylinder) with toroidal appendage and cylindrical internal buoy within the moon-pool is suggested in this research and its performance in various wave conditions is studied. The Linear Electric Generator (LEG), consisting of a permanent magnet and coils, is used as a direct Power Take-Off (PTO) system. To maximize the electrical energy extracted from the PTO system, the relative heave motions between the dual buoys must be highly amplified by the multiple resonance phenomena of dual-buoy and internal-fluid motions. The high-performance range can be widened by distributing those natural frequencies with respect to the peak frequency of the wave spectrum. The performance of the newly developed dual-buoy WEC was measured throughout the systematic 1:5.95-model test in regular and irregular waves conducted in a wave tank at Seoul National University. The model-test results are also validated by an independently developed numerical method.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.7 no.1
• /
• pp.116-125
• /
• 1995

Higher order nonlinear transfer functions are applied to model the nonlinear responses obtained Inn dynamic analysis of single degree of freedom systems (SDOF) subjected to wave and current loadings. The structural systems are subjected to single harmonic, two wave combination and irregular wave loading. Three different sources of nonlinearities are examined for each of the wave loading condition and it is shown that the nonlinear response appear at the resonance frequencies of the SDOF even when virtually no wave energy exists at those resonance frequencies. Higher order nonlinear transfer functions based on Volterra series representation are used to model the nonlinear responses mainly f3r the flexible systems and clearly shows the degrees of nonlinearity either as quadratic or cubic.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.79-87
• /
• 2015

This paper proposes a floating-type wave energy conversion system that consists of a mechanical part (yo-yo vibrating system, motion rectifying system, and power transmission system) and electrical part (power generation system). The yo-yo vibrating system, which converts translational input to rotational motion, is modeled as a single degree-of-freedom system. It can amplify the wave input via the resonance phenomenon and enhance the energy conversion efficiency. The electromechanical model is established from impedance matching of the mechanical part to the electrical system. The performance was analyzed at various wave frequencies and damping ratios for a wave input acceleration of 0.14 g. The maximum output occurred at the resonance frequency and optimal load resistance, where the power conversion efficiency and electrical output power reached 48% and 290 W, respectively. Utilizing the resonance phenomenon was found to greatly enhance the performance of the wave energy converter, and there exists a maximum power point at the optimum load resistance.

• Steel and Composite Structures
• /
• v.22 no.2
• /
• pp.277-299
• /
• 2016

In this paper, free vibration, forced vibration, resonance and stress wave propagation behavior in nanocomposite plates reinforced by wavy carbon nanotube (CNT) are studied by a mesh-free method based on first order shear deformation theory (FSDT). The plates are resting on Winkler-Pasternak elastic foundation and subjected to periodic or impact loading. The distributions of CNTs are considered functionally graded (FG) or uniform along the thickness and their mechanical properties are estimated by an extended rule of mixture. In the mesh-free analysis, moving least squares (MLS) shape functions are used for approximation of displacement field in the weak form of motion equation and the transformation method is used for imposition of essential boundary conditions. Effects of CNT distribution, volume fraction, aspect ratio and waviness, and also effects of elastic foundation coefficients, plate thickness and time depended loading are examined on the vibrational and stresses wave propagation responses of the nanocomposite plates reinforced by wavy CNT.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.9-13
• /
• 2008

The moving load such as a shock wave in a pipe propagates with a specific velocity. This internal load speed determines the level of flexural wave excitation and the possibility of resonant response leading to a large deformation. In this paper, we present particular solutions of displacements and the resonance conditions when the moving load is propagating in a pipe. These analytical results are compared to numerical simulations obtained using a hydrocode. We expect to identify potential explosion hazards in the general power industries.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.2
• /
• pp.27-31
• /
• 2002

The purpose of this study is to investigate the variation of resonance that is possible caused by construction of new port in a practical sea area between the existing port and the new one. The research of amplification that of the sea area was accomplished for the variation of resonance. In this study, long period wave that is observed continuously in the practical sea area was analyzed, and then secondary undulation was reproduced by numerical analysis. As a result of numerical analysis, the first mode resonant periods in the existing port is 640sec, and in the new one is 500sec. On the other hand, we know there is long period wave of 500sec from analyzation of field datas. Because that period this period is the resonant period in the new port. There is also the possibility of secondary undulation cause of resonant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.758-759
• /
• 2010

In this study, it was experimentally confirmed that the phenomenon of resonance effect of wave drag in two wavy walls. The channel had saw-tooth type of relief surfaces when supersonic gas flows into this channel. Experiment was carried out on the differential apparatus by conducting the comparative test of two nozzles (round sonic nozzle and two-dimensional nozzle with wavy walls). The two-dimensional nozzle was joined alternately with flat walls which had saw-tooth type of symmetrical and asymmetric reliefs. Two-dimensional nozzle was designed for the M=3 and profiled parabolic contour.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1028-1034
• /
• 2011

This paper have been studied that ocean wave power vibration generation system with two D.O.F.(degree of freedom) consists of buoy and vibration generation system with two D.O.F. for using efficiency of ocean wave energy. It selected main frequencies ${\omega}_1$, ${\omega}_2$ in frequency with ocean wave and it fitted them to the natural frequencies of vibration system with two D.O.F. in the vibrational power generation system. Then each the relative velocity of between the winding coil and the permanent magnet is faster than the velocity of ocean wave up and down motion by resonance phenomenon. Also the ocean wave power generation with two D.O.F. obtained the more electric energy then the ocean wave power generation with one D.O.F. by coupling effect for two D.O.F. vibration system. Therefore ocean wave power vibration generation system with two degree of freedom that is proposed in this paper has merits which not only using more energy in the ocean wave but also obtaining more electronic energy.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.180-181
• /
• 2002

Abstract. A surface plasmon resonance based on a ion-exchange glass waveguide investigated. we analyzed resonant coupling between TM-plarized waveguide mode and surface plasmon wave.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.324-324
• /
• 2008

Piezoelectric ceramics is an active element that makes stator to vibrate to generate rotational force in ultrasonic motors. In drive of ultrasonic motors, many factors that affect to the resonance characteristics of piezoelectric ceramics exist. For example, those factors are bonding condition with elastic body, the magnitude of electric field, the normal force for frictional drive and the emission of heat due to vibration and friction and so on. Therefore, it is important to research the inclination of property variation of piezoelectric ceramics in circumstance that has complex elements. In this paper, we focused and analyzed the resonance characteristics of ultrasonic motor due to the magnitude of the driving voltage and normal force.