• 전기학회논문지
• /
• 제63권3호
• /
• pp.383-388
• /
• 2014

This paper describes a wave modeling method using low-cost sensors. Wave modeling is applied to the wave monitoring system for accurate measurement of ocean wave parameters. The observation of ocean wave parameters is necessary to improve the accuracy of forecast of ocean wave condition. However, the ocean wave parameters measured by a low-cost wave monitoring system suffer from several errors. Therefore we introduce a wave modeling method to compensate the ocean wave parameters corrupted by errors. The proposed method is analyzed using experiments within controlled environment. It is verified that the accuracy of low-cost wave monitoring system can be increased by the proposed method.

• 한국패션뷰티학회지
• /
• 제3권3호
• /
• pp.56-63
• /
• 2005

In the study of permanent waving method after mixing ample and permanent wave solvent in permanent wave the dyed humans hair are as follows; First, Permanent waving method after mixing ample and permanent wave solvent is that the better effective way in permanent wave the dyed humans hair because permanent waving cycle is constant and hair cuticle is glossy. Second, This study is not interpret in permanent wave dyed humans hair that tensile strength is effect of permanent waving method after mixing ample and permanent wave solvent. A extension degree is effect of permanent waving method after mixing ample and permanent wave solvent use indifferent ample treatment method. Third, Hair cuticle damages are a little permanent waving method after mixing ample and permanent wave solvent in permanent wave dyed humans hair.

• 대한한의학회지
• /
• 제29권5호
• /
• pp.104-110
• /
• 2008

Objectives : The purpose of this study is to develop the method of selecting representative pulse wave. Methods : The pulse waves were acquired at the right and the left Guan point(關部) with 1420 people who were apparently healthy. The shape agreement of right and left pulse wave and the floating-sinking ratio were compared with three cases, which were the pulse height based method, the pulse area based method, and the pulse time based method. Results : In the point of the shape accordance, the pulse time based method was the best, and the pulse area based method was the worst. In the point of the floating-sinking ratio, the pulse height based method was the worst, and the pulse time based method was the best. Conclusions : So, the pulse time based method was recommended for selecting the representative pulse wave. This study compared the selection methods of representative pulse using the physiological characteristics of pulse wave. Further studies are required, because the representative pulse wave is the main factor of determining the shape and the floating-sinking characteristic of the pulse wave.

• 한국해양공학회지
• /
• 제34권6호
• /
• pp.406-418
• /
• 2020

In this study, a nonlinear wave simulation code is developed using a higher-order spectral (HOS) method. The HOS method is very efficient because it can determine the solution of the boundary value problem using fast Fourier transform (FFT) without matrix operation. Based on the HOS order, the vertical velocity of the free surface boundary was estimated and applied to the nonlinear free surface boundary condition. Time integration was carried out using the fourth order Runge-Kutta method, which is known to be stable for nonlinear free-surface problems. Numerical stability against the aliasing effect was guaranteed by using the zero-padding method. In addition to simulating the initial wave field distribution, a nonlinear adjusted region for wave generation and a damping region for wave absorption were introduced for wave generation simulation. To validate the developed simulation code, the adjusted simulation was carried out and its results were compared to the eighth order Stokes theory. Long-time simulations were carried out on the irregular wave field distribution, and nonlinear wave propagation characteristics were observed from the results of the simulations. Nonlinear adjusted and damping regions were introduced to implement a numerical wave tank that successfully generated nonlinear regular waves. According to the variation in the mean wave steepness, irregular wave simulations were carried out in the numerical wave tank. The simulation results indicated an increase in the nonlinear interaction between the wave components, which was numerically verified as the mean wave steepness. The results of this study demonstrate that the HOS method is an accurate and efficient method for predicting the nonlinear interaction between waves, which increases with wave steepness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.30-30
• /
• 2011

The wave-cutoff tool is a new diagnostic method to measure electron density and electron temperature. Most of the plasma diagnostic tools have the disadvantage that their application to processing plasma where toxic and reactive gases are used gives rise to many problems such as contamination, perturbation, precision of measurement, and so on. We can minimize these problems by using the wave-cutoff method. Here, we will present the results obtained through the development of the wave-cutoff diagnostic method. The frequency spectrum characteristics of the wave-cutoff probe will be obtained experimentally and analyzed through the microwave field simulation by using the CST-MW studio simulator. The plasma parameters are measured with the wave-cutoff method in various discharge conditions and its results will be compared with the results of Langmuir probe. Another disadvantage is that other diagnostic methods spend a long time (~ a few seconds) to measure plasma parameters. In this presentation, a fast measurement method will be also introduced. The wave-cutoff probe system consists of two antennas and a network analyzer. The network analyzer provides the transmission spectrum and the reflection spectrum by frequency sweeping. The plasma parameters such as electron density and electron temperature are obtained through these spectra. The frequency sweeping time, the time resolution of the wave-cutoff method, is about 1 second. A short pulse with a broad band spectrum of a few GHz is used with an oscilloscope to acquire the spectra data in a short time. The data acquisition time can be reduced with this method. Here, the plasma parameter measurement methods, Langmuir probe, pulsed wave-cutoff method and frequency sweeping wave-cutoff method, are compared. The measurement results are well matched. The real time resolution is less than 1 ?sec. The pulsed wave-cutoff technique is found to be very useful in the transient plasmas such as pulsed plasma and tokamak edge plasma.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제13권1호
• /
• pp.526-544
• /
• 2021

Based on the potential flow theory, a fully nonlinear numerical procedure is developed with boundary element method to analyze the interaction between a fixed semi-submersible platform and incident waves in open water. The incident wave is separated from the scattered wave under fully nonlinear boundary conditions. The mixed Euler-Lagrangian method is used to capture the position of the disturbed wave surface in local coordinate systems. The wave forces exerted on an inverted conical frustum are used to ensure the accuracy of the present method and good agreements with published results are obtained. The hydrodynamic characteristics of the semi-submersible platform interacting with regular waves are analyzed. Pressure distribution with time and space, tension and compression of the platform under wave action are investigated. 3D behaviors of wave run-ups are predicted. Strong nonlinear phenomena such as wave upwelling and wave interference are observed and analyzed.

• Ocean Systems Engineering
• /
• 제1권4호
• /
• pp.337-353
• /
• 2011

In the present study, an offshore platform having large partial porous cylindrical members, which are composed of permeable and impermeable cylinders, is suggested. In order to calculate the wave force on large partial porous cylindrical members, the fluid domain is divided into three regions: a single exterior region, N inner regions and N beneath regions, and the scattering wave in each fluid region is expressed by an Eigen-function expansion method. Applying Darcy's law to the porous boundary condition, the effect of porosity is simplified. Wave excitation forces and wave run up on the structures are presented for various wave conditions. For the idealized three-dimensional platform having large partial porous cylindrical members, the dynamic response evaluations of the platform due to wave forces are carried out through the modal analysis. In order to examine the effects of soil-structure interaction, the substructure method is also applied. The displacement and bending stress at the selective nodal points of the structure are computed using various input parameters, such as the shear-wave velocity of soil, the wave height and the wave period. Applying the Monte Carlo Simulation (MCS) method, the reliability evaluations at critical structure members, which contained uncertainties caused by dynamic forces and structural properties, are examined by the reliability index with the results obtained from MCS.

• 한국해양학회지
• /
• 제28권3호
• /
• pp.192-201
• /
• 1993

쯔나미파에 의한 피해를 줄이기 위해서는 쯔나미파를 재현할 수 있는 방법의 개발 이 필요하다. 본 논문에서는 Sign Method를 도입하여 검조기에 기록된 쯔나미파를 분 석하고 재현해 봄으로써, 쯔나미파 분석에서의 Sign Method의 사용가능성을 검토하였 다. 쯔나미파의 시계열자료 Y(t)는 각 쯔나미의 발생특징을 반영하는 함수인 source evolution function E(t')와 파가 전파되는 지역의 특징을 나타내는 함수인 wave propagation function K9t-t')의 convolution 적분에 의해 나타낼 수 있다. Y(t)=.int. E(t')K(t-t')dt' 일본의 6개 지점과 한국의 9개 지점에서 기록된 1940년, 1964년, 1983년의 쯔나미파를 분석하여 sourve function 들과 wave function들을 구하 고, 두 함수를 이용하여 기록자료도 재현해 보았다. 우리 나라 동해안처럼 쯔나미의 진원지로부터 멀리 위치한 지역에서는 Sign Metho가 효과적인 방법임을 알 수 있었다. 또한, 기록되지 않은 쯔나미파도 인접지점의 source function 과 다른 시기의 쯔나미 에 대한 wave function을 이용하여 추정할 수 있다.

• 한국해안·해양공학회논문집
• /
• 제22권3호
• /
• pp.163-170
• /
• 2010

평면파 근사식에 기초한 지형에 의한 파랑변형 모형인 산란체법과 변환행렬법을 비교하여 특성을 분석하였다. 산란체법의 결과가 기존 엄밀해에 보다 근접하고 내재한 물리현상을 보다 명확히 설명하는 것으로 평가된다. 이들은 해석해로 계산이 빠르고 용이하며 지형이 비교적 단순한 경우에는 상당한 정밀도를 보인다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.928-933
• /
• 2007

In this research, we investigated active vibration control based on wave-viewpoint using the longitudinal wave separation method. The control strategy is the one of active vibration control technique for generating vibration reduced zone and uses wave information including the directivity as the cost function. In order to get the wave information from the measured values, we proposed and examined the time-domain longitudinal wave separation method proper to real time application like active vibration control. Using the proposed method, we examine the performance and feasibility of active vibration control based wave view-point through the simulation. The related experimental verification and application is going to be expected in a near future.