• Composites Research
• /
• v.26 no.5
• /
• pp.328-333
• /
• 2013

In this study, bone plate made of glass/polypropylene composite material which was applied to an artificial bone was tested to check the service ability under fatigue loading. To check serviceability of composite bone plates fatigue test was carried out considering changes in the moisture absorption rate, locking position of screws and loading condition. Test results showed that all the tested specimens had the fatigue life more than one million cycles which was much higher fatigue life than the expected value of 650,000 cycles. Screw position was not critical impact on the deformation of the fracture site. In this paper, the mechanical performance of the glass/polypropylene composite was verified by fatigue test under various water absorption conditions, and this result may give useful information on the design of composite bone plate.

• Resources Recycling
• /
• v.29 no.6
• /
• pp.57-64
• /
• 2020

In this study, removal of OCA and organic impurities for recycling LCD touch panel glass was conducted by mechanical and chemical dissolution methode. Cut mill and oscillation mill were used for mechanical crushing of touch panel, and water, ethanol, dichloromethane were used to remove OCA and organic impurities. As a result of TGA, when applied only dicloromethane in the process, the efficiency of organic removal was to be best. In addition, removal effect of organic impurities increased as the cleaning temperature increased. As a result of zeta potential analysis to confirm the dispersion degree of touch panel glass in the solvent, the absolute value of the zeta potenial of water with the lowest cleaning effect was lower than other solvents, and it was confirmed that efficiency of organic removal is affected not only by the chemical dissolution properties but also the physical dispersion properties in the solvent.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.4
• /
• pp.381-392
• /
• 2023

This research scrutinizes the mechanical characteristics of ultra-high strength concrete using oxide graphene nanoplatelet(GO) and hollow glass powder(HGP). The investigation covered various mechanical attributes, including workability, compression strength, tensile strength, water resistance, and the internal microstructure of standard concrete. Our findings reveal that workability experiences a significant improvement with the incorporation of a minimal amount of HGP, and an increase was also observed in tensile strength and water resistance. It was confirmed that cGO(C company GO) and HGP demonstrated commendable dispersion and the pore volume exhibited a reduction of more than 20%. The potential of cGO and HGP to substitute silica fume(SF) was also explored. Consequently, it was found that both workability and mechanical properties were enhanced in the absence of SF when cGO and HGP were used. This finding implies that the utilization of these novel materials could potentially modify conventional methods of concrete manufacturing.

• Environmental Analysis Health and Toxicology
• /
• v.7 no.3_4
• /
• pp.81-84
• /
• 1992

Physical compositions of solid waste in Wonju, shopping area were investigated with combustibles 78.13% (papers 35.89%, foods 14.41% etc.) incombustibles 21.87% (glass and ceramics 11.02%, metals 6.0% etc.) in 1991, solid waste in apartment area were investigated with combustibles 84.27% (foods 34.29%, papers 22.58% etc.), incombustibles 15.73% (glass and ceramics 8.77%, metals 4.85% etc.) and residence area were characterised with combustibles 70.37% (foods 33.55% , papers 10.53% etc.) and incombustibles 29.63% (ash of briquet 17.29%, glass and ceramics 7.49% etc.). Water qualities of a leachate from municipal landfill of Wonju city were analysed pH 8.0~8.4, total suspended solid 102~140 mg/1, CN￣ 0.003~ 0.008 mg/1, NO$_2$-N 0.108~0.294 mg/1 and phenols 0.46~1.12 mg/1. Volume of the leachate for 20% methemoglobin formation were 0.2~0.4 mg/ml in Octever, 0.3~0.4 ml/ml in December sampling, 0.2~0.3 ml/ml in St.1 and 0.4 ml/ml in St.3.

• Journal of Ocean Engineering and Technology
• /
• v.9 no.1
• /
• pp.57-62
• /
• 1995

The hygrothermal effect on three different types of Glass/Polypropylene was investigated under the environment of 4$0^{\circ}C$ distilled water. The residual strength of Glass/Polypropylene with randomly oriented and fiber content of 4-wt%(R40) was found stable under the moisture content of 0.2%. In this case, the maximum moisture content was 0.53%. On the other hand, Glass/Polypropylene with unidirection and 42wt%(U42) and 50st%(U50) fiber content, respectively, showed the residual strength less stable than R40. However, the maximam moisture contents were 0.52% and 0.45% respectively.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 1999.11a
• /
• pp.111-115
• /
• 1999

The $Li_2O-MgO-MgF_2-SiO_2$glasses with addition of $B_2O_3$ were investigated in order to make glass-ceramics for low temperature firing substrate. Glasses were made by melting at $1450^{\circ}C$ in the electronic furnace and crystallized at $750^{\circ}C$. After the crystallization, crystal phases and microstructure were observed. The crystal phases were polycrystalline of lithium boron fluorphlogopite and lithium fluorhectorite. The crystal shape was changed to grande type from needle type with the increase in $B_2O_3$ contents. Average particle size of the glass-ceramics aftar water swelling was $3.77{\mu}{\textrm}{m}$. The optimum sintering temperature and sintering shrinkage of the substrate were $900^{\circ}C$ and 13.4vol%, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.5 no.1
• /
• pp.31-38
• /
• 1998

저온소결기판용 Glass-ceramics를 제조하기 위해 LiO2-MgO-MgF2-SiO2계 조성에 서 B2O3첨가가 결정화 특성 및 물성에 미치는 영향을 고찰하였다. 145$0^{\circ}C$에서용융하여 제조 한 모유리의 핵형성 온도와 결정화 온도를 결정하기 위해 TMA와 DTA분석을 실시하였다. 결정화시킨 유리의 결정상과 미세구조를 관찰하기 위하여 XRD와 SEM관찰을 실시하였다. Water swelling을 통해 Glass-ceramics powder를 제조하였으며 제조한 powder의 평균입자 크기는 8.32$\mu$m였다.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.09a
• /
• pp.21-23
• /
• 2002

Two sampling methods for chlorofluorocarbons(CFCs) in groundwater were compared and assessed with groundwater samples in Jeju Island. CFCs concentrations from copper tube method were widely variable among triplicates and higher than those from flame-sealed glass ampule method. For the copper tube method, this is aggravated by rubber packings in the faucet of discharge line of wells, which was removed for the glass ampule method. The poor reproducibility and apparent contamination of results by copper tube method is due to the improper sealing of copper tubes and materials in water discharge line. This suggests that it is more difficult to achieve complete isolation from the atmosphere in the copper tube method and that materials that could release CFCs should be avoided along the sampling flow lines. It seems that the flame-sealed glass ampule method is more relevant for groundwater sampling for CFCs though it requires more complicated equipments and procedures.

• Analytical Science and Technology
• /
• v.5 no.3
• /
• pp.309-317
• /
• 1992

Inorganic/organic composite was synthesized by using sol-gel process, and the bonding characteristics of composite was investigated with glass transition temperature(Tg), measured by DMTA(Dynamic Mechanical Thermal Analyzer). It was found from shift of Tg to higher temperature that composite reaction was proceeded better with the amount of HCl and water. But Tg was not varied with reaction time.

• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.668-676
• /
• 1990

Glass in the ZrO2-SiO2 system containing up to 30mol% ZrO2 were prepared by heating the gel made from the mixed solutions of Zr(OC3H7)4 and partial hydrolysed Si(OC2H5)4. As a result, the monolith gel was made from the HCl and water content as 2.7$\times$10-3 and 8 molar ratio to alkoxide and drying temoperature as 4$0^{\circ}C$. Heating rate of dry gel maintained under 0.5$^{\circ}C$/min and heating at a temperature as 90$0^{\circ}C$ was found to be for making the transparent glass.