• 콘크리트학회논문집
• /
• 제28권2호
• /
• pp.205-212
• /
• 2016

본 연구는 고로슬래그 미분말(GGBFS)의 구성성분이 알칼리 활성화 슬래그 시멘트(AASC)에 미치는 영향에 관한 연구이다. 산화알루미늄($Al_2O_3$)을 고로슬래그 미분말 중량에 대해 2~16% 혼합하였다. 활성화제는 KOH를 사용하였고, 물-결합재 비는 0.5이다. 강도 향상은 $Al_2O_3$ 혼합률이 증가함에 따라 수화반응의 향상으로 나타난다. 재령 28일에서 가장 높은 강도는 2M KOH + 16% $Al_2O_3$와 4M KOH + 16% $Al_2O_3$일 때이고 각각 30.8 MPa과 45.2 MPa이였다. 재령 28일에서 2M KOH + 16% $Al_2O_3$의 강도는 2M KOH ($Al_2O_3$ 미첨가) 보다 46% 향상되었다. 또한 4M KOH + 16% $Al_2O_3$의 강도는 4M KOH ($Al_2O_3$ 미첨가) 보다 44% 향상되었다. 결합재에서 $Al_2O_3$ 혼합률이 증가함에 따라 모든 재령에서 강도가 증가하였다. AASC에서 초음파속도(UPV)는 강도와 유사한 경향을 나타내었지만 흡수율과 공극률은 $Al_2O_3$의 혼합률이 증가함에 따라 강도경향과 상반된 경향을 나타내었다. $Al_2O_3$ 혼합률이 높은 시험체에서 반응생성물질의 Al/Ca와 Al/Si가 증가하였다. SEM과 EDX 분석을 통해 $Al_2O_3$의 혼합은 더욱 치밀한 미세조직을 형성한 것을 확인하였다.

• Bulletin of the Korean Chemical Society
• /
• 제24권1호
• /
• pp.86-90
• /
• 2003

Reverse-Water-Gas-Shift reaction (RWGSR) was carried out over the ZnO, $Al_2O_3,\;and\;ZnO/Al_2O_3$ catalysts at the temperature range from 400 to 700 ℃. The ZnO showed good specific reaction activity but this catalyst was deactivated. All the catalysts except the $ZnO/Al_2O_3$ catalyst (850 ℃) showed low stability for the RWGSR and was deactivated at the reaction temperature of 600 ℃. The $ZnO/Al_2O_3$ catalyst calcined at 850 ℃ was stable during 210 hrs under the reaction conditions of 600 ℃ and 150,000 GHSV, showing CO selectivity of 100% even at the pressure of 5 atm. The high stability of the $ZnO/Al_2O_3$ catalyst (850 ℃) was attributed to the prevention of ZnO reduction by the formation of $ZnAl_2O_4$ spinel structure. The spinel structure of $ZnAl_2O_4$ phase in the $ZnO/Al_2O_3$ catalyst calcined at 850 ℃ was confirmed by XRD and electron diffraction.

• 한국수소및신에너지학회논문집
• /
• 제30권2호
• /
• pp.95-102
• /
• 2019

In order to investigate the effect of water treatment on activity of WGS catalyst, $Cu/ZnO/MgO/Al_2O_3$ (CZMA) catalysts were synthesized by co-precipitation method. The prepared catalysts were water-treated at two different temperature (250, $350^{\circ}C$). Synthesized catalysts were characterized by using BET, SEM, $N_2O$ chemisorption, XRD, $H_2-TPR$ and XPS analysis. The catalytic activity tests were carried out at a GHSV of $28,000h^{-1}$ and a temperature range of $180-320^{\circ}C$. The reduction temperature decreased with water treatment and CZMA_250 catalyst showed the lowest reduction temperature and retained a large amount of $Cu^+$. Water-treated catalysts showed increased reactivity compared to untreated catalyst and the CZMA_250 catalyst showed higher catalytic activity on WGS reaction.

• 대한기계학회논문집B
• /
• 제32권9호
• /
• pp.669-675
• /
• 2008

The objectives of this paper are to examine the effect of nano-particles on the pool type absorption heat transfer enhancement and to find the optimal conditions to design a highly effective compact absorber for ammonia/water absorption system. The effect of $Al_2O_3$ nano-particles and carbon nanotube(CNT) on the absorption performance is studied experimentally. The experimental ranges of the key parameters are 20% of ammonia concentration, $0{\sim}0.08\;vol%$ (volume fraction) of CNT particles, and $0{\sim}0.06 \;vol%$ of $Al_2O_3$ nano-particles. For the ammonia/water nanofluids, the heat transfer rate and absorption rate with 0.02 vol% $Al_2O_3$ nano-particles were found to be 29% and 18% higher than those without nano-particles, respectively. It is recommended that the concentration of 0.02 vol% of $Al_2O_3$ nano-particles be the best candidate for ammonia/water absorption performance enhancement.

• 한국응용과학기술학회지
• /
• 제27권4호
• /
• pp.421-426
• /
• 2010

The transesterification of rapeseed oil, soybean oil, and mixed fat were conducted at $65^{\circ}C$ with $Al_2O_3$-supported CaO, 0.8 wt% KOH, 1 wt% NaOH and mixed catalyst. The overall conversion(%) of rapeseed oil indicated to be 96% at the 12:1 molar ratio of methanol to oil, 8 wt% CaO and 2 wt% water. The pH ranges of biodiesel for mixed fat using four catalysts and for three fats using 8wt% CaO were 7.3-9.1, 7.3-7.5, respectively. The volumes of water needed to wash biodiesel from rapeseed oil using 0.8 wt% KOH and 8 wt% CaO were 15 mL and 3 mL.

• 한국분무공학회지
• /
• 제20권2호
• /
• pp.65-69
• /
• 2015

In this study, the thermal performance of vehicle's cooling system is experimentally investigated using the water/coolant-based $Al_2O_3$ nanofluids as working fluids. For the purpose, the water/coolant-based $Al_2O_3$ nanofluids are prepared by twostep method with gum arabic. In order to obtain the well-suspended nanofluids, the agglomerated $Al_2O_3$ nanoparticles are precipitated using centrifugal force and the experiments are performed with supernatant of them. The thermal conductivity is measured by transient hot wire method and the thermal conductivity of nanofluids is enhanced up to 4.8% as compared to that of base fluids. Moreover, the cooling performance of water/coolant-based $Al_2O_3$ nanofluids is evaluated using vehicle's engine simulator under the constant RPM condition. The results show that the cooling performance of automobile engine increases up to 5.9% using prepared nanofluids. To investigate the effect of nanofluids on exhaust gas, the $NO_x$ emission is measured during the operation with respect to time and 10.3% of $NO_x$ emission is decreased. The experimental results imply that the water/coolant-based $Al_2O_3$ nanofluids might be used as a next-generation vehicles' coolant

• 한국세라믹학회지
• /
• 제20권1호
• /
• pp.49-54
• /
• 1983

The main object of this study is to investigate the effect of Al powder as an additive on the sintering of calcined alumina comparing with that of calcined alumina alone. The degree of Al oxidation is calculated by measuring the weight increase during the firing Water absorption bulk density and compressive strength of the $Al_2O_3+Al$ system at each temperature are compared with those of $Al_2O_4$ alone. The $Al_2O_3+Al$ system shows better physical propeties than Al2O3 alone and it seems by the SEM observation that the fine oxidized Al particles(fine $Al_2O_3$ particles submicron unit) fill the interstices of the original $Al_2O_3$ par-ticles and thus result in the well-close-packed arrangement of the particles.

• 한국세라믹학회지
• /
• 제39권6호
• /
• pp.528-534
• /
• 2002

CaO ceramics were prepared by conventional sintering process and their hydration behaviors were evaluated by measuring weight increment on saturated water vapor pressure at ambient temperature. CaCO$_3$ and limestone were used as CaO source materials and $Al_2$O$_3$, MgO and SiO$_2$ were added as sintering agents. $Al_2$O$_3$ was a liquid phase sintering agent to increase densification and grain growth rates, whereas MgO and SiO$_2$, densification and grain growth inhibitors. Regardless of composition, all of the prepared CaO ceramics showed the improved hydration resistance as bulk density increased. Especially, when bulk density was more than 3.0 g/㎤, there was no weight increment after 120 h of hydration. Therefore, to decrease contact area between CaO and water vapor by increasing bulk density with the $Al_2$O$_3$ sintering additive was effective for the improvement of CaO hydration resistance.

• 한국수소및신에너지학회논문집
• /
• 제22권6호
• /
• pp.905-912
• /
• 2011

In this study, the novel concept catalytic reactor was designed for water-gas shift reaction (WGS) under high pressure. The novel concept catalytic reactor was composed of an autoclave, the catalyst, and liquid water. Cu-ZnO/$Al_2O_3$ as the low temperature shift catalyst was used for WGS reaction. WGS in the novel concept catalytic reactor was carried out at the ranges of 150~$250^{\circ}C$ and 30~50 atm. The liquid water was filled at the bottom of the autoclave catalytic reactor and the catalyst of pellet type was located at the gas-liquid water interface. It was concluded that WGS reaction occurred over the surface of catalysts partially wetted with liquid water. The conversion of CO for WGS was also controlled with changing content of Cu and ZnO used as the catalytic active components. Meanwhile, the catalyst of honey comb type coated with Cu-ZnO/$Al_2O_3$ was used in order to increase the contact area between wet-surface of catalyst and the reactants of gas phase. It was confirmed from these experiments that $H_2$/CO ratio of the simulated coal gas increased from 0.5 to 0.8 by WGS at gas-liquid water interface over the wet surface of honey comb type catalyst at $250^{\circ}C$ and 50 atm.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.130-137
• /
• 2011

Experimental investigations are conducted to figure out the feasibility of $Al_2O_3$ nanofluids as the alternative coolant for car engine. For the purpose, the thermal conductivities and viscosities of water/commercial coolant based $Al_2O_3$ nanofluids with 0.3, 1.0, 2.0 and 3.0 vol. % at temperatures ranging from $25^{\circ}C$ to $35^{\circ}C$ are measured. Thermal conductivities are measured using the transient hot-wire method and also viscosities are measured by Brookfield LVDV-III rheometer. Based on the results, it is shown that thermal conductivity of $Al_2O_3$ nanofluids with 3.0 vol. % is increased about 11% at $35^{\circ}C$ and the increment of viscosity approaches to 84% at shear rate of 600(1/s) and 80% at shear rate of 960(1/s) in the same temperature. with fundamental data for the thermal conductivity and viscosity of the nanofluids, the feasibility of $Al_2O_3$ nanofluids as the alternative coolant for car engine are discussed.